IC Phoenix
 
Home ›  VV3 > VN610SP-E-VN610SPTR-E,SINGLE CHANNEL HIGH SIDE DRIVER
VN610SP-E-VN610SPTR-E Fast Delivery,Good Price
Part Number:
If you need More Quantity or Better Price,Welcom Any inquiry.
We available via phone +865332716050 Email
Partno Mfg Dc Qty AvailableDescript
VN610SP-E |VN610SPESTN/a10avaiSINGLE CHANNEL HIGH SIDE DRIVER
VN610SPTR-E |VN610SPTRESTMN/a10000avaiSINGLE CHANNEL HIGH SIDE DRIVER
VN610SPTR-E |VN610SPTRESTN/a200avaiSINGLE CHANNEL HIGH SIDE DRIVER
VN610SPTR-E |VN610SPTREST,STN/a42000avaiSINGLE CHANNEL HIGH SIDE DRIVER


VN610SPTR-E ,SINGLE CHANNEL HIGH SIDE DRIVERAbsolute Maximum RatingsSymbol Parameter Value UnitV DC supply voltage 41 VCC-V Reverse DC supply v ..
VN610SPTR-E ,SINGLE CHANNEL HIGH SIDE DRIVERFeatures Figure 1. PackageType R I VDS(on) out CCVN610SP-E 10 mΩ 45 A 36 V ■ OUTPUT CURRENT: 45 A ..
VN610SPTR-E ,SINGLE CHANNEL HIGH SIDE DRIVERBlock DiagramVCC OVERVOLTAGEVCCUNDERVOLTAGECLAMPPwCLAMP DRIVER OUTPUT GND ILIMVDSLIMLOGICIOUTCURREN ..
VN66AFD ,Enhancement-Mode MOSFET TransistorsS-04279—Rev. E, 16-Jul-0111-2TN0601L, VN0606L, VN66AFDVishay Siliconix        ..
VN66AFD ,Enhancement-Mode MOSFET TransistorsS-04279—Rev. E, 16-Jul-0111-1TN0601L, VN0606L, VN66AFDVishay Siliconix     ..
VN750 ,HIGH SIDE DRIVERVN750 / VN750S/ VN750PT / VN750-B5®HIGH SIDE DRIVERTYPE R I VDS(on) OUT CCVN750VN750S60 mΩ 6 A 36 V ..
WE2408 , 2.4GHz Single Chip FM Transceiver
WE9140A , TONE/PULSE SWITCHABLE DIALER WITH REDIAL
WE9140A , TONE/PULSE SWITCHABLE DIALER WITH REDIAL
WE9140G , TONE/PULSE SWITCHABLE DIALER WITH REDIAL
WE9140J , TONE/PULSE SWITCHABLE DIALER WITH REDIAL
WE9142 , 10-MEMORY TONE/PULSE SWITCHABLE DIALER


VN610SP-E-VN610SPTR-E
SINGLE CHANNEL HIGH SIDE DRIVER
1/18October 2004
VN610SP-E

SINGLE CHANNEL HIGH SIDE DRIVER
Rev. 1
Table 1. General Features

� OUTPUT CURRENT: 45 A
� CMOS COMPATIBLE INPUT
� PROPORTIONAL LOAD CURRENT SENSE
� UNDERVOLTAGE AND OVERVOLTAGEn
SHUT-DOWN
� OVERVOLTAGE CLAMP
� THERMAL SHUT DOWN
� CURRENT LIMITATION
� VERY LOW STAND-BY POWER DISSIPATION
� PROTECTION AGAINST: LOSS OF GROUND AND LOSS OF VCC
� REVERSE BATTERY PROTECTION (*)
� IN COMPLIANCE WITH THE 2002/95/EC
EUROPEAN DIRECTIVE
DESCRIPTION

The VN610SP-E is a monolithic device made
using STMicroelectronics VIPower M0-3
technology. It is intended for driving resistive or
inductive loads with one side connected to ground.
Active VCC pin voltage clamp protects the device
against low energy spikes (see ISO7637 transient
compatibility table).
Figure 1. Package

This device integrates an analog current sense
which delivers a current proportional to the load
current (according to a known ratio). Active current
limitation combined with thermal shut-down and
automatic restart protect the device against
overload. Device automatically turns off in case of
ground pin disconnection.
Table 2. Order Codes

Note: (*) See application schematic at page 9
VN610SP-E
Figure 2. Block Diagram
Table 3. Absolute Maximum Ratings
3/18
VN610SP-E
Figure 3. Configuration Diagram (Top View) & Suggested Connections for Unused and N.C. Pins
Figure 4. Current and Voltage Conventions
Table 4. Thermal Data

Note:(1) When mounted on a standard single-sided FR-4 board with 0.5cm2 of Cu (at least 35μm thick).
Note:(2) When mounted on a standard single-sided FR-4 board with 6 cm2 of Cu (at least 35μm thick).
VN610SP-E
ELECTRICAL CHARACTERISTICS

(8V(Per each channel)
Table 5. Power

Note:1. Vclamp and VOV are correlated. Typical difference is 5V.
Table 6. Protection (see note 2)

Note:2. To ensure long term reliability under heavy overload or short circuit conditions, protection and related diagnostic signals must be
used together with a proper software strategy. If the device is subjected to abnormal conditions, this software must limit the duration
and number of activation cycles
Table 7. VCC - Output Diode
5/18
VN610SP-E
ELECTRICAL CHARACTERISTICS (continued)
Table 8. Current Sense (9V≤VCC≤16V) (See Figure 5)

Note:3. Current sense signal delay after positive input slope.
Table 9. Switching (VCC=13V)
VN610SP-E
Table 10. Logic Input
Figure 5.
Table 11. Truth Table
7/18
VN610SP-E
Figure 6. Switching Characteristics (Resistive load RL=0.87Ω)
Table 12. Electrical Transient Requirements On VCC Pin
VN610SP-E
Figure 7. Waveforms
9/18
VN610SP-E
Figure 8. Application Schematic
GND PROTECTION NETWORK AGAINST
REVERSE BATTERY

can be used with any type of load.
The following is an indication on how to dimension the
RGND resistor.
1) RGND ≤ 600mV / (IS(on)max).
2) RGND ≥ (−VCC) / (-IGND)
where -IGND is the DC reverse ground pin current and can
be found in the absolute maximum rating section of the
device’s datasheet.
Power Dissipation in RGND (when VCC<0: during reverse
battery situations) is:
PD= (-VCC)2 /RGND
This resistor can be shared amongst several different
HSD. Please note that the value of this resistor should be
calculated with formula (1) where IS(on)max becomes the
sum of the maximum on-state currents of the different
devices.
Please note that if the microprocessor ground is not
common with the device ground then the RGND will
produce a shift (IS(on)max * RGND) in the input thresholds
and the status output values. This shift will vary
depending on how many devices are ON in the case of
several high side drivers sharing the same RGND.
If the calculated power dissipation leads to a large
resistor or several devices have to share the same
resistor then the ST suggests to utilize Solution 2 (see
below).
Solution 2: A diode (DGND) in the ground line.
A resistor (RGND=1kΩ) should be inserted in parallel to
DGND if the device will be driving an inductive load.
This small signal diode can be safely shared amongst
several different HSD. Also in this case, the presence of
the ground network will produce a shift (j 600mV) in the
input threshold and the status output values if the
microprocessor ground is not common with the device
ground. This shift will not vary if more than one HSD
shares the same diode/resistor network.
Series resistor in INPUT line is also required to prevent
that, during battery voltage transient, the current exceeds
the Absolute Maximum Rating.
Safest configuration for unused INPUT pin is to leave it
unconnected, while unused SENSE pin has to be
connected to Ground pin.
LOAD DUMP PROTECTION

Dld is necessary (Voltage Transient Suppressor) if the
load dump peak voltage exceeds VCC max DC rating.
The same applies if the device will be subject to
transients on the VCC line that are greater than the ones
shown in the ISO T/R 7637/1 table.
μC I/Os PROTECTION:
If a ground protection network is used and negative
transients are present on the VCC line, the control pins will
be pulled negative. ST suggests to insert a resistor (Rprot)
in line to prevent the μC I/Os pins to latch-up.
The value of these resistors is a compromise between the
leakage current of μC and the current required by the
HSD I/Os (Input levels compatibility) with the latch-up
limit of μC I/Os.
-VCCpeak/Ilatchup ≤ Rprot ≤ (VOHμC-VIH-VGND) / IIHmax
Calculation example:
For VCCpeak= - 100V and Ilatchup ≥ 20mA; VOHμC ≥ 4.5V
5kΩ ≤ Rprot ≤ 65kΩ.
Recommended Rprot value is 10kΩ.
ic,good price


TEL:86-533-2716050      FAX:86-533-2716790
   

©2020 IC PHOENIX CO.,LIMITED