IC Phoenix
 
Home ›  TT42 > TL852-TL852CDR-TL852CN,Sonar Ranging Receiver
TL852-TL852CDR-TL852CN Fast Delivery,Good Price
Part Number:
If you need More Quantity or Better Price,Welcom Any inquiry.
We available via phone +865332716050 Email
Partno Mfg Dc Qty AvailableDescript
TL852TARALOGICN/a80avaiSonar Ranging Receiver
TL852CDRTIN/a1avaiSonar Ranging Receiver
TL852CNTIBBN/a2avaiSonar Ranging Receiver


TL852 ,Sonar Ranging Receivermaximum ratings over operating free-air temperature range (unless otherwise noted)Voltage at any pi ..
TL852CDR ,Sonar Ranging Receiver     SLSS003 − SEPTEMBER 1983 − REVISED MARCH 1988N PACKAGE Designed for Use Wit ..
TL852CN ,Sonar Ranging Receivermaximum ratings may cause permanent damage to the device. This is a stress rating only, andfunction ..
TL880 , DTVPC Decoder
TL880 , DTVPC Decoder
TL880 , DTVPC Decoder
TMC2072KHC ,Genlocking Video DigitizerFunctional Descriptionafter reset; 2) loss and recovery of lock while operating; or The TMC2072, a ..
TMC2192KHC ,10 Bit EncoderFunctional Description . . . . . . . . . . . . . . . .7Parallel Microprocessor Interface . . . . . ..
TMC2193KJC ,10 Bit EncoderFunctional Description . . . . . . . . . . . . . . . .7Parallel Microprocessor Interface . . . . . ..
TMC22071AKHC ,Genlocking Video DigitizerFeatures Description• Fully integrated acquisitionThe TMC22071A Genlocking Video Digitizer converts ..
TMC22153AKHC ,Multistandard Digital Video DecoderGeneral Description......4 Programmable V Scalar.. 56Input Processor4 Programmable Y Scalar.. 56Ada ..
TMC22191KHC ,Digital Video Encoders/Layering EngineFeatures• 3 power-down modes• All-digital video encoding• Built-in color bars and modulated ramp te ..


TL852-TL852CDR-TL852CN
Sonar Ranging Receiver
to 90 kHz TTL-Compatible Operates From Power Sources of 4.5 V
to 6.8 V
Interfaces to Electrostatic or Piezoelectric
Transducers
Overall Gain Adjustable With One External
Resistor


description

The TL852 is an economical sonar ranging receiver integrated circuit for use with the TL851 control integrated
circuit. A minimum of external components is required for operation, and this amplifier easily interfaces to
Polaroid’s 50-kHz electrostatic transducer. An external 68-kΩ ±5% resistor from BIAS to GND provides the
internal biasing reference. Amplifier gain can be set with a resistor from G1IN to GADJ. Required amplifier gain
will vary for different applications. Using the detect-level measurement circuit of Figure 1, a nominal
peak-to-peak value of 230 mV input during gain step 2 is recommended for most applications. For reliable
operation, a level no lower than 50 mV should be used. The recommended detect level of 230 mV can be
obtained for most amplifiers with an R1 value between 5 kΩ and 20 kΩ
Digital control of amplifier gain is provided with gain control inputs GCA, GCB, GCC, and GCD. These inputs
must be driven synchronously (all inputs stable within 0.1 µs) to avoid false receive output signals due to invalid
logic counts. This can be done easily with the TL851 control integrated circuit. A plot showing relative gain for
the various gain steps versus time can be seen in Figure 2. To dampen ringing of the 50-kHz electrostatic
transducer, a 5-kΩ resistor from G1IN to XIN is recommended.
An external parallel combination of inductance and capacitance between LC and VCC provides an amplifier with
an externally controlled gain and Q. This not only allows control of gain to compensate for attenuation of signal
with distance, but also maximizes noise and sidelobe rejection. Care must be taken to accurately tune the L-C
combination at operating frequency or gain and Q will be greatly reduced at higher gain steps.
AC coupling between stages of the amplifier is accomplished with a 0.01-mF capacitor for proper biasing.
The receive output is normally held at a low level by an internal 1-µA current source. When an input of sufficient
amplitude is received, the output is driven alternately by the 1-µA discharge current and a 50-µA charging
current. A 1000-pF capacitor is required from REC to GND to integrate the received signal so that one or two
noise pulses will not be recognized.
XIN provides clamping for the transformer secondary when used for transducer transmit drive as shown in
Figure 4 of the SN28827 data sheet.
The TL852 is characterized for operation from 0°C to 40°C.
ic,good price


TEL:86-533-2716050      FAX:86-533-2716790
   

©2020 IC PHOENIX CO.,LIMITED