IC Phoenix
 
Home ›  TT24 > TDA7293,120V-100W DMOS AUDIO AMPLIFIER WITH MUTE/ST-BY
TDA7293 Fast Delivery,Good Price
Part Number:
If you need More Quantity or Better Price,Welcom Any inquiry.
We available via phone +865332716050 Email
Partno Mfg Dc Qty AvailableDescript
TDA7293STN/a262avai120V-100W DMOS AUDIO AMPLIFIER WITH MUTE/ST-BY


TDA7293 ,120V-100W DMOS AUDIO AMPLIFIER WITH MUTE/ST-BYTDA7293®120V - 100W DMOS AUDIO AMPLIFIER WITH MUTE/ST-BYVERY HIGH OPERATING VOLTAGE RANGEMULTIPOWER ..
TDA7293V ,120V-100W DMOS AUDIO AMPLIFIER WITH MUTE/ST-BYTDA7293®120V - 100W DMOS AUDIO AMPLIFIER WITH MUTE/ST-BYVERY HIGH OPERATING VOLTAGE RANGEMULTIPOWER ..
TDA7294 ,100VTDA7294®100V - 100W DMOS AUDIO AMPLIFIER WITH MUTE/ST-BYVERY HIGH OPERATING VOLTAGE RANGEMULTIPOWER ..
TDA7294V ,100V 100W DMOS audio amplifier with mute/st-byTDA7294®100V - 100W DMOS AUDIO AMPLIFIER WITH MUTE/ST-BYVERY HIGH OPERATING VOLTAGE RANGEMULTIPOWER ..
TDA7295 ,80V-80W DMOS AUDIO AMPLIFIER WITH MUTE/ST-BYTDA7295®80V - 80W DMOS AUDIO AMPLIFIER WITH MUTE/ST-BYVERY HIGH OPERATING VOLTAGE RANGEMULTIPOWER B ..
TDA7295S ,80Vapplicationscan be delivered to very low impedance loads, so(Home Stereo, self powered loudspeakers ..
THC63LVDM83D , REDUCED SWING LVDS 24Bit COLOR HOST-LCD PANEL INTERFACE
THC63LVDM83D , REDUCED SWING LVDS 24Bit COLOR HOST-LCD PANEL INTERFACE
THC63LVDM87 , LOW POWER / SMALL PACKAGE / 24Bit COLOR LVDS TRANSMITTER
THC63LVDM87 , LOW POWER / SMALL PACKAGE / 24Bit COLOR LVDS TRANSMITTER
THCV213 , LVDS SerDes transmitter and receiver
THCV215 , THCV215 is designed to support video data transmission between the host and display.


TDA7293
120V-100W DMOS AUDIO AMPLIFIER WITH MUTE/ST-BY
TDA7293
120V - 100W DMOS AUDIO AMPLIFIER WITH MUTE/ST-BY
VERY HIGH OPERATING VOLTAGE RANGE
(±50V)
DMOS POWER STAGE
HIGH OUTPUT POWER (100W @ THD =
10%, RL = 8Ω, VS = ±40V)
MUTING/STAND-BY FUNCTIONS
NO SWITCH ON/OFF NOISE
VERY LOW DISTORTION
VERY LOW NOISE
SHORT CIRCUIT PROTECTED (WITH NO IN-
PUT SIGNAL APPLIED)
THERMAL SHUTDOWN
CLIP DETECTOR
MODULARITY (MORE DEVICES CAN BE
EASILY CONNECTED IN PARALLEL TO
DRIVE VERY LOW IMPEDANCES)
DESCRIPTION

The TDA7293 is a monolithic integrated circuit in
Multiwatt15 package, intended for use as audio
class AB amplifier in Hi-Fi field applications
(Home Stereo, self powered loudspeakers, Top-
class TV). Thanks to the wide voltage range and
to the high out current capability it is able to sup-
ply the highest power into both 4Ω and 8Ω loads.
The built in muting function with turn on delay
simplifies the remote operation avoiding switching
on-off noises.
Parallel mode is made possible by connecting
more device through of pin11. High output power
can be delivered to very low impedance loads, so
optimizing the thermal dissipation of the system.
Figure 1: Typical Application and Test Circuit
ABSOLUTE MAXIMUM RATINGS
PIN CONNECTION (Top view)
THERMAL DATA
TDA7293

2/15
ELECTRICAL CHARACTERISTICS (Refer to the Test Circuit VS = ±40V, RL = 8Ω, Rg = 50 Ω;
Tamb = 25°C, f = 1 kHz; unless otherwise specified).
Note (1): GVmin ≥ 26dB
Note: Pin 11 only for modular connection. Max external load 1MΩ/10 pF, only for test purpose
Note (**): Tested with optimized Application Board (see fig. 2)
TDA7293

3/15
Figure 2: Typical Application P.C. Board and Component Layout (scale 1:1)
TDA7293

4/15
APPLICATION SUGGESTIONS (see Test and Application Circuits of the Fig. 1)
The recommended values of the external components are those shown on the application circuit of Fig-
ure 1. Different values can be used; the following table can help the designer.
(*) R1 = R3 for pop optimization
(**) Closed Loop Gain has to be ≥ 26dB
(***) Multiplay this value for the number of modular part connected
Slave function: pin 4 (Ref to pin 8 -VS) Note:

If in the application, the speakers are connected
via long wires, it is a good rule to add between
the output and GND, a Boucherot Cell, in order to
avoid dangerous spurious oscillations when the
speakers terminal are shorted.
The suggested Boucherot Resistor is 3.9Ω/2W
and the capacitor is 1μF.
TDA7293

5/15
INTRODUCTION
In consumer electronics, an increasing demand
has arisen for very high power monolithic audio
amplifiers able to match, with a low cost, the per-
formance obtained from the best discrete de-
signs.
The task of realizing this linear integrated circuit
in conventional bipolar technology is made ex-
tremely difficult by the occurence of 2nd break-
down phoenomenon. It limits the safe operating
area (SOA) of the power devices, and, as a con-
sequence, the maximum attainable output power,
especially in presence of highly reactive loads.
Moreover, full exploitation of the SOA translates
into a substantial increase in circuit and layout
complexity due to the need of sophisticated pro-
tection circuits.
To overcome these substantial drawbacks, the
use of power MOS devices, which are immune
from secondary breakdown is highly desirable.
The device described has therefore been devel-
oped in a mixed bipolar-MOS high voltage tech-
nology called BCDII 100/120.
1) Output Stage

The main design task in developping a power op-
erational amplifier, independently of the technol-
ogy used, is that of realization of the output stage.
The solution shown as a principle shematic by
Fig3 represents the DMOS unity - gain output
buffer of the TDA7293.
This large-signal, high-power buffer must be ca-
pable of handling extremely high current and volt-
age levels while maintaining acceptably low har-
monic distortion and good behaviour over
frequency response; moreover, an accurate con-
trol of quiescent current is required.
A local linearizing feedback, provided by differen-
tial amplifier A, is used to fullfil the above require-
ments, allowing a simple and effective quiescent
current setting.
Proper biasing of the power output transistors
alone is however not enough to guarantee the ab-
sence of crossover distortion.
While a linearization of the DC transfer charac-
teristic of the stage is obtained, the dynamic be-
haviour of the system must be taken into account.
A significant aid in keeping the distortion contrib-
uted by the final stage as low as possible is pro-
vided by the compensation scheme, which ex-
ploits the direct connection of the Miller capacitor
at the amplifier’s output to introduce a local AC
feedback path enclosing the output stage itself.
2) Protections

In designing a power IC, particular attention must
be reserved to the circuits devoted to protection
of the device from short circuit or overload condi-
tions.
Due to the absence of the 2nd breakdown phe-
nomenon, the SOA of the power DMOS transis-
tors is delimited only by a maximum dissipation
curve dependent on the duration of the applied
stimulus.
In order to fully exploit the capabilities of the
power transistors, the protection scheme imple-
mented in this device combines a conventional
SOA protection circuit with a novel local tempera-
ture sensing technique which " dynamically" con-
trols the maximum dissipation.
Figure 3: Principle Schematic of a DMOS unity-gain buffer.
TDA7293

6/15
In addition to the overload protection described
above, the device features a thermal shutdown
circuit which initially puts the device into a muting
state (@ Tj = 150 o C) and then into stand-by (@
Tj = 160 oC).
Full protection against electrostatic discharges on
every pin is included.
3) Other Features

The device is provided with both stand-by and
mute functions, independently driven by two
CMOS logic compatible input pins.
The circuits dedicated to the switching on and off
of the amplifier have been carefully optimized to
avoid any kind of uncontrolled audible transient at
the output.
The sequence that we recommend during the
ON/OFF transients is shown by Figure 4.
The application of figure 5 shows the possibility of
using only one command for both st-by and mute
functions. On both the pins, the maximum appli-
cable range corresponds to the operating supply
voltage.
APPLICATION INFORMATION

HIGH-EFFICIENCY
Constraints of implementing high power solutions
are the power dissipation and the size of the
power supply. These are both due to the low effi-
ciency of conventional AB class amplifier ap-
proaches.
Here below (figure 6) is described a circuit pro-
posal for a high efficiency amplifier which can be
adopted for both HI-FI and CAR-RADIO applica-
tions.
Figure 5: Single Signal ST-BY/MUTE Control

Circuit
Figure 4: Turn ON/OFF Suggested Sequence
TDA7293

7/15
The TDA7293 is a monolithic MOS power ampli-
fier which can be operated at 100V supply voltage
(120V with no signal applied) while delivering out-
put currents up to ±6.5 A.
This allows the use of this device as a very high
power amplifier (up to 180W as peak power with
T.H.D.=10 % and Rl = 4 Ohm); the only drawback
is the power dissipation, hardly manageable in
the above power range.
The typical junction-to-case thermal resistance of
the TDA7293 is 1 o C/W (max= 1.5 o C/W). To
avoid that, in worst case conditions, the chip tem-
perature exceedes 150 o C, the thermal resistance
of the heatsink must be 0.038 o C/W (@ max am-
bient temperature of 50 oC).
As the above value is pratically unreachable; a
high efficiency system is needed in those cases
where the continuous RMS output power is higher
than 50-60 W.
The TDA7293 was designed to work also in
higher efficiency way.
For this reason there are four power supply pins:
two intended for the signal part and two for the
power part.
T1 and T2 are two power transistors that only
operate when the output power reaches a certain
threshold (e.g. 20 W). If the output power in-
creases, these transistors are switched on during
the portion of the signal where more output volt-
age swing is needed, thus "bootstrapping" the
power supply pins (#13 and #15).
The current generators formed by T4, T7, zener
diodes Z1, Z2 and resistors R7,R8 define the
minimum drop across the power MOS transistors
of the TDA7293. L1, L2, L3 and the snubbers C9,
R1 and C10, R2 stabilize the loops formed by the
"bootstrap" circuits and the output stage of the
TDA7293.
By considering again a maximum average
output power (music signal) of 20W, in case
of the high efficiency application, the thermal
resistance value needed from the heatsink is
2.2o C/W (Vs =±50 V and Rl= 8 Ohm).
All components (TDA7293 and power transis-
tors T1 and T2) can be placed on a 1.5o C/W
heatsink, with the power darlingtons electrically
insulated from the heatsink.
Since the total power dissipation is less than that
of a usual class AB amplifier, additional cost sav-
ings can be obtained while optimizing the power
supply, even with a high heatsink .
BRIDGE APPLICATION

Another application suggestion is the BRIDGE
configuration, where two TDA7293 are used.
In this application, the value of the load must not
be lower than 8 Ohm for dissipation and current
capability reasons.
A suitable field of application includes HI-FI/TV
subwoofers realizations.
The main advantages offered by this solution are:
- High power performances with limited supply
voltage level.
- Considerably high output power even with high
load values (i.e. 16 Ohm).
With Rl= 8 Ohm, Vs = ±25V the maximum output
power obtainable is 150 W, while with Rl=16
Ohm, Vs = ±40V the maximum Pout is 200 W.
APPLICATION NOTE: (ref. fig. 7)
Modular Application (more Devices in Parallel)

The use of the modular application lets very high
power be delivered to very low impedance loads.
The modular application implies one device to act
as a master and the others as slaves.
The slave power stages are driven by the master
device and work in parallel all together, while the in-
put and the gain stages of the slave device are dis-
abled, the figure below shows the connections re-
quired to configure two devices to work together.
The master chip connections are the same as
the normal single ones.
The outputs can be connected together with-
out the need of any ballast resistance.

The slave SGND pin must be tied to the nega-
tive supply.
The slave ST-BY and MUTE pins must be con-
nected to the master ST-BY and MUTE pins.
The bootstrap lines must be connected to-
gether and the bootstrap capacitor must be in-
creased: for N devices the boostrap capacitor
must be 22μF times N.
The slave IN-pin must be connected to the
negative supply.
THE BOOTSTRAP CAPACITOR

For compatibility purpose with the previous de-
vices of the family, the boostrap capacitor can be
connected both between the bootstrap pin (6) and
the output pin (14) or between the boostrap pin
(6) and the bootstrap loader pin (12).
When the bootcap is connected between pin 6
and 14, the maximum supply voltage in presence
of output signal is limited to 100V, due the boot-
strap capacitor overvoltage.
When the bootcap is connected between pins 6
and 12 the maximum supply voltage extend to the
full voltage that the technology can stand: 120V.
This is accomplished by the clamp introduced at
the bootstrap loader pin (12): this pin follows the
output voltage up to 100V and remains clamped
at 100V for higher output voltages. This feature
lets the output voltage swing up to a gate-source
voltage from the positive supply (VS -3 to 6V).
TDA7293

8/15
ic,good price


TEL:86-533-2716050      FAX:86-533-2716790
   

©2020 IC PHOENIX CO.,LIMITED