STTH806DIRG ,Turbo 2 ultrafastapplications. Table 1. Absolute ratings (limiting values per diode at 25° C, unless otherwi ..
STTH806DTI ,TANDEM 600V HYPERFAST BOOST DIODEFEATURES AND BENEFITSInsulated TO-220ABn ESPECIALLY SUITED AS BOOST DIODE INCONTINUOUS MODE POWER F ..
STTH806DTI. ,TANDEM 600V HYPERFAST BOOST DIODE®STTH806DTITandem 600V HYPERFAST BOOST DIODEMAJOR PRODUCTS CHARACTERISTICS12I 8AF(AV)V 600 VRRMTj ( ..
STTH806G , Turbo 2 ultrafast - high voltage rectifier
STTH806TTI ,TURBOSWITCHFEATURES AND BENEFITS Insulated TO-220ABn ESPECIALLY SUITED AS BOOST DIODE INCONTINUOUS MODE POWER ..
STTH810D ,Ultrafast recoveryapplications. The improved performance in low leakage current, and therefore thermal runaway guard ..
T6668 ,-0.3 to +6.0V; V(in/out): -0.3 to +0.3V; CMOS LSI for voice recording and reproducing using the ADM systemELIE D " '3tP17iiYH1 DDELI‘ILIE Ell: .TOSB T6668_1||
TOSHIBA (UC/UP)
1. GENERAL
The T6668 is ..
T6801 ,Single-channel driver 25 mA output with thermal monitoringFeatures Input Comparator with Schmitt-trigger Characteristic Input Clamping Current Capability o ..
T6801-TAQ ,Single-channel Driver IC with Driver IC with MonitoringFeatures Input Comparator with Schmitt-trigger Characteristic Input Clamping Current Capability o ..
T6816 ,40-V dual Hexdriver with serial input controlapplications and the industrial 24-V supply.It controls up to 12 different loads via a 16-bit dataw ..
T6816 ,40-V dual Hexdriver with serial input controlFeatures• Six High-side and Six Low-side Drivers Outputs Freely Configurable as Switch, Half Brid ..
T6816 ,40-V dual Hexdriver with serial input controlapplications.Overvoltage protection is matched to the requirements of the 24-V industrial voltagean ..
STTH806DIRG
Turbo 2 ultrafast
August 2006 Rev 2 1/9
STTH806 urbo 2 ultrafast - high voltage rectifier
Main product characteristics
Features and benefits Ultrafast switching Low reverse current Low thermal resistance Reduces conduction and switching losses Insulated package TO-220AC Ins Insulated voltage: 2500 VRMS Typical package capacitance: 7 pF
DescriptionThe STTH806 uses ST Turbo2 600 V technology.
This device is specially suited for use in switching
power supplies, and industrial applications.
Order codes
Table 1. Absolute ratings (limiting values per diode at 25° C, unless otherwise specified) condition to avoid thermal runaway for a diode on its own heatsinkdPtotj
--------------- 1thja–()
------- -------------------<
Characteristics STTH8062/9
1 Characteristics To evaluate the conduction losses use the following equation:
P = 1.07 x IF(AV) + 0.041 IF2 (RMS)
Table 2. Thermal parameters
Table 3. Static electrical characteristics Pulse test: tp = 5 ms, δ < 2 % Pulse test: tp = 380 µs, δ < 2 %
Table 4. Dynamic characteristics
STTH806 Characteristics 3/9
Figure 1. Conduction losses versus
average current
Figure 2. Forward voltage drop versus
forward current
Figure 3. Relative variation of thermal
impedance junction to case versus
pulse duration
Figure 4. Peak reverse recovery current
versus dIF /dt (typical values)
Figure 5. Reverse recovery time versus F /dt (typical values)
Figure 6. Reverse recovery charges versus F /dt (typical values)
Characteristics STTH8064/9
Figure 7. Softness factor versus
dIF/dt (typical values)
Figure 8. Relative variations of dynamic
parameters versus junction
temperature
Figure 9. Transient peak forward voltage
versus dIF /dt (typical values)
Figure 10. Forward recovery time versus F /dt (typical values)
Figure 11. Junction capacitance versus
reverse voltage applied
(typical values)
Figure 12. Thermal resistance junction to
ambient versus copper surface
under tab (printed circuit board
FR4, eCU = 35 µm)
STTH806 Package mechanical data 5/9
Package mechanical dataEpoxy meets UL94, V0
Cooling method: by conduction (C)
Recommended torque value: 0.80 Nm
Maximum torque value: 1.0 Nm
Figure 13.D2 PAK Footprint dimensions (in mm)
Table 5. D2 PAK Dimensions
Package mechanical data STTH8066/9
Table 6. TO-220AC Dimensions
