STTH6010W ,Ultrafast recoveryapplications. The improved performance in low leakage current, and therefore thermal runaway guard ..
STTH6012W ,Ultrafast recoveryapplications. The improved performance in low leakage current, and therefore thermal runaway guard ..
STTH60P03SW ,ULTRAFAST RECTIFIER PDP ENERGY RECOVERYFEATURES AND BENEFITSTO-247■ Ultrafast recovery allowing High Sustain Frequency STTH60P03SW■ Decrea ..
STTH8003CY ,HIGH FREQUENCY SECONDARY RECTIFIERSFEATURES AND BENEFITSn COMBINES HIGHEST RECOVERY ANDVOLTAGE PERFORMANCE.A2n ULTRA-FAST, SOFT AND NO ..
STTH802 ,Ultrafast recovery diodeSTTH802Ultrafast recovery diodeMain product characteristicsKAI 8 AF(AV)V 200 VRRMT 175° Cj (max)KV ..
STTH802CB-TR ,HIGH EFFICIENCY ULTRAFAST DIODEapplications.ABSOLUTE RATINGS (limiting values)Symbol Parameter Value UnitV Repetitive peak reverse ..
T6668 ,-0.3 to +6.0V; V(in/out): -0.3 to +0.3V; CMOS LSI for voice recording and reproducing using the ADM systemELIE D " '3tP17iiYH1 DDELI‘ILIE Ell: .TOSB T6668_1||
TOSHIBA (UC/UP)
1. GENERAL
The T6668 is ..
T6801 ,Single-channel driver 25 mA output with thermal monitoringFeatures Input Comparator with Schmitt-trigger Characteristic Input Clamping Current Capability o ..
T6801-TAQ ,Single-channel Driver IC with Driver IC with MonitoringFeatures Input Comparator with Schmitt-trigger Characteristic Input Clamping Current Capability o ..
T6816 ,40-V dual Hexdriver with serial input controlapplications and the industrial 24-V supply.It controls up to 12 different loads via a 16-bit dataw ..
T6816 ,40-V dual Hexdriver with serial input controlFeatures• Six High-side and Six Low-side Drivers Outputs Freely Configurable as Switch, Half Brid ..
T6816 ,40-V dual Hexdriver with serial input controlapplications.Overvoltage protection is matched to the requirements of the 24-V industrial voltagean ..
STTH6010W
Ultrafast recovery
March 2006 Rev 1 1/8
STTH6010Ultrafast recovery - high voltage diode
Main product characteristics
Features and benefits Ultrafast, soft recovery Very low conduction and switching losses High frequency and/or high pulsed current
operation High reverse voltage capability High junction temperature
DescriptionThe high quality design of this diode has
produced a device with low leakage current,
regularly reproducible characteristics and intrinsic
ruggedness. These characteristics make it ideal
for heavy duty applications that demand long term
reliability.
Such demanding applications include industrial
power supplies, motor control, and similar
mission-critical systems that require rectification
and freewheeling. These diodes also fit into
auxiliary functions such as snubber, bootstrap,
and demagnetization applications.
The improved performance in low leakage
current, and therefore thermal runaway guard
band, is an immediate competitive advantage for
this device.
Order codes
Characteristics STTH60102/8
1 Characteristics To evaluate the conduction losses use the following equation:
P = 1.3 x IF(AV) + 0.0067 IF2 (RMS)
Table 1. Absolute ratings (limiting values at 25° C, unless otherwise specified)
Table 2. Thermal parameters
Table 3. Static electrical characteristics Pulse test: tp = 5 ms, δ < 2 % Pulse test: tp = 380 µs, δ < 2 %
STTH6010 Characteristics 3/8
Table 4. Dynamic characteristics
Figure 1. Conduction losses versus
average current
Figure 2. Forward voltage drop versus
forward current
Figure 3. Relative variation of thermal
impedance junction to case
versus pulse duration
Figure 4. Peak reverse recovery current
versus dIF/dt (typical values)
Characteristics STTH60104/8
Figure 5. Reverse recovery time versus
dIF/dt (typical values)
Figure 6. Reverse recovery charges versus
dIF/dt (typical values)
Figure 7. Softness factor versus
dIF/dt (typical values)
Figure 8. Relative variations of dynamic
parameters versus junction
temperature
STTH6010 Characteristics 5/8
Figure 9. Transient peak forward voltage
versus dIF/dt (typical values)
Figure 10. Forward recovery time versus dIF/dt
(typical values)
Figure 11. Junction capacitance versus
reverse voltage applied (typical
values)
Package information STTH60106/8
2 Package informationEpoxy meets UL94, V0
Cooling method: by conduction (C)
Recommended torque value: 0.80 Nm
Maximum torque value: 1.0 Nm
In order to meet environmental requirements, ST offers these devices in ECOPACK®
packages. These packages have a Lead-free second level interconnect . The category of
second level interconnect is marked on the package and on the inner box label, in
compliance with JEDEC Standard JESD97. The maximum ratings related to soldering
conditions are also marked on the inner box label. ECOP ACK is an ST trademark.
ECOP ACK specifications are available at: .
Table 5. DO-247 dimensions
