STTH6004W ,Ultrafast high voltage rectifierapplications, as an output rectification diode. Table 2: Order codesPart number MarkingSTTH6004W ST ..
STTH6006CW , HIGH FREQUENCY SECONDARY RECTIFIER
STTH6006W ,Turbo 2 ultrafastapplications. Table 3. Absolute ratings (limiting values per diode at 25° C, unless otherwi ..
STTH6010W ,Ultrafast recoveryapplications. The improved performance in low leakage current, and therefore thermal runaway guard ..
STTH6012W ,Ultrafast recoveryapplications. The improved performance in low leakage current, and therefore thermal runaway guard ..
STTH60P03SW ,ULTRAFAST RECTIFIER PDP ENERGY RECOVERYFEATURES AND BENEFITSTO-247■ Ultrafast recovery allowing High Sustain Frequency STTH60P03SW■ Decrea ..
T6668 ,-0.3 to +6.0V; V(in/out): -0.3 to +0.3V; CMOS LSI for voice recording and reproducing using the ADM systemELIE D " '3tP17iiYH1 DDELI‘ILIE Ell: .TOSB T6668_1||
TOSHIBA (UC/UP)
1. GENERAL
The T6668 is ..
T6801 ,Single-channel driver 25 mA output with thermal monitoringFeatures Input Comparator with Schmitt-trigger Characteristic Input Clamping Current Capability o ..
T6801-TAQ ,Single-channel Driver IC with Driver IC with MonitoringFeatures Input Comparator with Schmitt-trigger Characteristic Input Clamping Current Capability o ..
T6816 ,40-V dual Hexdriver with serial input controlapplications and the industrial 24-V supply.It controls up to 12 different loads via a 16-bit dataw ..
T6816 ,40-V dual Hexdriver with serial input controlFeatures• Six High-side and Six Low-side Drivers Outputs Freely Configurable as Switch, Half Brid ..
T6816 ,40-V dual Hexdriver with serial input controlapplications.Overvoltage protection is matched to the requirements of the 24-V industrial voltagean ..
STTH6004W
Ultrafast high voltage rectifier
1/6
Table 1: Main product characteristics
STTH6004WUltrafast high voltage rectifier
Table 3: Absolute ratings (limiting values)October 2005 REV. 1
Features and benefits Ultrafast switching Low reverse current Low thermal resistance Reduces switching & conduction losses
DescriptionThe STTH6004W uses ST 400V technology and
is specially suited for use in switching power
supplies, welding equipment and industrial
applications, as an output rectification diode.
Table 2: Order codes
STTH6004W
Table 4: Thermal Resistance
Table 5: Static electrical characteristicsPulse test: * tp = 5 ms, δ < 2%
** tp = 380 µs, δ < 2%
To evaluate the conduction losses use the following equation: P = 0.8 x IF(AV) + 0.0033 IF2 (RMS)
Table 6: Dynamic characteristics
Figure 1: Conduction losses versus average
forward current
Figure 2: Forward voltage drop versus forward
current
STTH6004W3/6
Figure 3: Relative variation of thermal
impedance junction to case versus pulse
duration
Figure 4: Peak reverse recovery current versus
dIF/dt (typical values)
Figure 5: Reverse recovery time versus dIF/dt
(typical values)
Figure 6: Reverse recovery charges versus
dIF/dt (typical values)
Figure 7: Reverse recovery softness factor
versus dIF /dt (typical values)
Figure 8: Relative variations of dynamic
parameters versus junction temperature
STTH6004W
Figure 9: Transient peak forward voltage
versus dIF/dt (typical values)
Figure 10: Forward recovery time versus dIF/dt
(typical values)
Figure 11: Junction capacitance versus
reverse voltage applied (typical values)
STTH6004W5/6
Figure 12: DO-247 Package mechanical dataIn order to meet environmental requirements, ST offers these devices in ECOPACK® packages. These
packages have a Lead-free second level interconnect . The category of second level interconnect is
marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97. The
maximum ratings related to soldering conditions are also marked on the inner box label. ECOPACK is an
ST trademark. ECOPACK specifications are available at: .
Table 7: Ordering information Epoxy meets UL94, V0 Cooling method: by conduction (C) Recommended torque value: 0.8 Nm. Maximum torque value: 1.0 Nm.
Table 8: Revision history
STTH6004W. consequences
of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted
by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject
to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not
authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics.
The ST logo is a registered trademark of STMicroelectronics.
All other names are the property of their respective owners
© 2005 STMicroelectronics - All rights reserved
STMicroelectronics group of companies - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan -
Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
