STA2051 ,32-BIT SINGLE CHIP BASEBAND CONTROLLER FOR GPS AND TELEMATIC APPLICATIONSFEATURESFigure 1. Packages■ ARM7TDMI 16/32 bit RISC CPU based host microcontroller.■ Complete Embed ..
STA2500DTR ,Bluetooth蛺2;2; V2.1 + EDR ("Lisbon") for automotive applicationsfeatures . 195.5 Bluetooth controller V2.1 + EDR (“Lisbon”) . . . . . . . 195.6 Processor and ..
STA301A , NPN Darlington With built-in avalanche diode
STA302 , PNP Darlington General purpose/3-phase motor drive
STA303 , NPN Darlington General purpose/3-phase motor drive
STA304 ,DIGITAL AUDIO PROCESSOR WITH MULTICHANNEL DDX(TM)STA304DIGITAL AUDIO PROCESSOR WITH MULTICHANNEL DDX™PRODUCT PREVIEW■ END TO END DIGITAL AUDIO INTEG ..
STS2301 , P-Channel E nhancement Mode Field Effect Transistor
STS2301 , P-Channel E nhancement Mode Field Effect Transistor
STS2306 , N-Channel E nhancement Mode Field Effect Transistor
STS2306 , N-Channel E nhancement Mode Field Effect Transistor
STS2307 , P-Channel E nhancement Mode Field Effect Transistor
STS2308A , N-Channel Enhancement Mode Field Effect Transistor
STA2051
32-BIT SINGLE CHIP BASEBAND CONTROLLER FOR GPS AND TELEMATIC APPLICATIONS
1/5
STA2051
VESPUCCISeptember 2004
FEATURES ARM7TDMI 16/32 bit RISC CPU based host
microcontroller. Complete Embedded Memory System: FLASH 256K bytes + 16K bytes (100K eras-
ing/programming cycles) RAM 64K bytes. External memory interface provides glueless
support for up to four banks of external SRAM,
FLASH, ROM. 12 channel GPS correlation DSP: – no TCXO
required RTCA-SC159 / WAAS / EGNOS support GPS performance accuracy: stand alone <30m; differential
<1m; surveying <1cm time to first fix: autonomous start 90s; cold
start 45s; warm start 7s; obscuration 1s. CMOS M8T (0.18 um) technology. -40°C to 85°C operating temperature range. 144-pin TQFP144 package or 64-pin TQFP64
package Power Supply: 2.7V to 3.6V operating supply range for Input/
Output periphery 3 V to 3.6V operating supply range for A/ D
Converter reference 1.8V operating supply range for core supply
provided either by internal Voltage Regulator
with external stabilization capacitor, or by ex-
ternal supply for higher power efficiency. 0-66MHz internal clock frequency managed by
a Reset and Clock Control Unit; the unitisable to
provide low power modes (WAIT, SLOW,
STOP, STANDBY) and to generate the internal
clock from the external reference through
integrated PLL. 48 programmable General Purpose I/O, each
pin programmable independently as digital input
or digital output; 40 (30 in TQFP64) are
multiplexed with peripheral functions; 16 can
generate an interrupt on input level/transition. Real time clock module with 3 2 KHz low power
oscillator and separate power supply to
continue running during stand-by mode. 16-bit Watchdog Timer with 8 bits prescaler for
system reliability and integrity. CAN module compliant with the CAN
specification V2.0 part B (active). The bit rate
can be programmed up to 1 MBaud. Four16-bit programmable Timers with 7 bit
prescaler, up to two input capture/output
compare, one pulse counter function, one PWM
channel with selectable frequency each. 4 channels 12-bit sigma-delta Analog to Digital
Converter, single channel or multi channel
conversion modes, single-shotor continuous
conversion modes, sample rate1KHz (4 KHz
when single channel), conversion range 0-2.5V. Three Serial Communication Interfaces (UART)
allow full duplex, asynchronous,
communications with external devices,
independently programmable TX and RX baud
rates up to 625K baud. One UART adapted to suit Smart Card interface
needs, for asynchronous SC as defined by ISO
7816-3; it includes SC clock generation. Two Serial Peripheral Interfaces (SPI) allow full
duplex, synchronous communications with
external devices, master or slave operation,
max baud rate: 8Mb/s. One SPI may be used as
Multimedia Card interface. Two I2 C Interfaces provide multi-master and
slave functions, support normal and fast I2C
mode (400KHz), 7/10 bit addressing modes.
One I2 C Interface is multiplexed with one SPI,
so either 2xSPI+1xI2 C or 1xSPI+2xI2 C may be
DATA BRIEF32-BIT SINGLE CHIP BASEBAND CONTROLLER
FOR GPS AND TELEMATIC APPLICATIONS
Rev. 1
STA2051 - VESPUCCIused at a time. USB unit V1.1 compliant, software configurable end point setting, USB Suspend/Resume support.
(TQFP144 only) High Level Data Link Controller (HDLC) unit supports full duplex operating mode, NRZ, NRZI, FM0 and
MANCHESTER modes, internal 8bit Baud Rate Generator.
Figure 2. System Block Diagram
3/5
STA2051 - VESPUCCI
Figure 3. TQFP144 Pins Connection Diagram (Top view)
STA2051 - VESPUCCI
Figure 4. TQFP64 Pins Connection Diagram (Top view)
Table 2. Revision History
. consequences
of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted
by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject
to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not
authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics.
The ST logo is a registered trademark of STMicroelectronics.
All other names are the property of their respective owners
© 2004 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
- Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan -
Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
5/5
STA2051 - VESPUCCI
:
www.ic-phoenix.com
.
