SSM2142P-SSM2142S Fast Delivery |IC PHOENIX CO.,LIMITED

SSM2142S ,Balanced Line DriverGENERAL DESCRIPTIONBased on a cross-coupled, electronically balanced topology, theThe SSM2142 is an ..
SSM2142S-REEL ,Balance Line DriverGENERAL DESCRIPTIONBased on a cross-coupled, electronically balanced topology, theThe SSM2142 is an ..
SSM2142SZ ,Balance Line DriverSpecifications subject to change without notice.ABSOLUTE MAXIMUM RATINGS*PIN CONNECTIONSSupply Volt ..
SSM2142SZ-REEL ,Balance Line DriverFEATURESTransformer-Like Balanced OutputDrives 10 V RMS Into a 600 V LoadVINStable When Driving Lar ..
SSM2143 ,-6 dB Differential Line Receiverspecifications apply at T = +258C)AParameter Symbol Conditions Min Typ Max UnitsAUDIO PERFORMANCETo ..
SSM2143. ,-6 dB Differential Line Receiverapplications, a gain of 2 can berealized by reversing the +IN/–IN and SENSE/REFERENCEconnections.Wh ..
STAC9708 , Multi-Channel AC97 Codec With Multi-Codec Option
STAC9723T , Stereo AC 97 Codec With Multi-Codec Option
START405TR ,NPN SILICON RF TRANSISTORSTART405NPN Silicon RF Transistor• LOW NOISE FIGURE: NFmin = 1.1dB @ 1.8GHz, 2mA, 2V• COMPRESSION ..
START499ETR ,NPN Silicon RF TransistorAbsolute maximum ratings (T = +25°C) CSymbol Parameter Value UnitV Collector emitter voltage 4.5 V ..
STB0899 ,STB0899 databriefSTB0899Multistandard advance demodulator STB0899Digital TV satellite set-top boxesDATA BRIEFDESCRIP ..
STB0899 ,STB0899 databriefSTB0899Multistandard advance demodulator STB0899Digital TV satellite set-top boxesDATA BRIEFDESCRIP ..

SSM2142P-SSM2142S
Balanced Line Driver
FUNCTIONAL BLOCK DIAGRAM
REV.BBalanced Line Driver
FEATURES
Transformer-Like Balanced Output
Drives 10 V RMS Into a 600 V Load
Stable When Driving Large Capacitive Loads and Long
Cables
Low Distortion
0.006% typ 20 Hz–20 kHz, 10 V RMS into 600 V
High Slew Rate
15 V/ms typ
Low Gain Error
(Differential or Single-Ended); 0.7% typ
Outputs Short-Circuit Protected
Available In Space-Saving 8-Pin Mini-DIP Package
Low Cost
APPLICATIONS
Audio Mix Consoles
Distribution Amplifiers
Graphic and Parametric Equalizers
Dynamic Range Processors
Digital Effects Processors
Telecommunications Systems
Industrial Instrumentation
Hi-Fi Equipment
GENERAL DESCRIPTION
The SSM2142 is an integrated differential-output buffer
amplifier that converts a single-ended input signal to a balanced
output signal pair with high output drive. By utilizing low noise
thermally matched thin film resistors and high slew rate
amplifiers, the SSM2142 helps maintain the sonic quality of
audio systems by eliminating power line hum, RF interference,
voltage drops, and other externally generated noise commonly
encountered with long audio cable runs. Excellent rejection of
common-mode noise and offset errors is achieved by laser
trimming of the onboard resistors, assuring high gain accuracy.
The carefully designed output stage of the SSM2142 is capable
of driving difficult loads, yielding low distortion performance
despite extremely long cables or loads as low as 600 Ω, and is
stable over a wide range of operating conditions.
Based on a cross-coupled, electronically balanced topology, the
SSM2142 mimics the performance of fully balanced
transformer-based solutions for line driving. However, the
SSM2142 maintains lower distortion and occupies much less
board space than transformers while achieving comparable
common-mode rejection performance with reduced parts count.
The SSM2142 in tandem with the SSM2141 differential
receiver establishes a complete, reliable solution for driving and
receiving audio signals over long cables. The SSM2141 features
an Input Common-Mode Rejection Ratio of 100 dB at 60 Hz.
Specifications demonstrating the performance of this typical
system are included in the data sheet.
SSM2142–SPECIFICATIONS
NOTESOutput common-mode offset voltage can be removed by inserting dc blocking capacitors in the sense lines. See Applications Information.
Specifications subject to change without notice.
(VS = 618 V, –408C ≤ TA ≤ +858C, operating in differential mode unless otherwise
noted. Typical characteristics apply to operation at TA = +258C.)
ABSOLUTE MAXIMUM RATINGS*
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .±18 V
Storage Temperature . . . . . . . . . . . . . . . . . .–60°C to +150°C
Lead Temperature (Soldering, 60 sec) . . . . . . . . . . . .+300°C
Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . .+150°C
Operating Temperature Range . . . . . . . . . . . .–40°C to +85°C
Output Short Circuit Duration (Both Outputs) . . . .Indefinite
*Stresses above those listed under “Absolute Maximum Ratings” may cause
permanent damage to the device. These are stress ratings only; the functional
operation of the device at these or any other conditions above those indicated in the
operational sections of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect device reliability.
ORDERING GUIDE
PIN CONNECTIONS
8-Pin Plastic DIP
(P Suffix)
16-Pin Wide Body SOL
(S Suffix)
Typical Performance Characteristics
FREQUENCY – Hz
1001k10k100k
POWER SUPPLY REJECTION – dB
Figure 3.Power Supply Rejection vs. Frequency
SUPPLY VOLTAGE – Volts
OUTPUT VOLTAGE SWING – V rms±10±14±18
Figure 5.Output Voltage Swing vs. Supply Voltage
Figure 4.Maximum Output Voltage Swing vs. Frequency
Figure 6.Supply Current vs. Supply Voltage
VOUT
300Ω
600Ω+18V
–18VVS= 0V
VCMR= 10V p–p
ΔVOUT
VCMROCMR = 20 LOG5
Figure 1.Output CMR Test Circuit
Figure 2.Signal Balance Ratio (BBC Method) Test Circuit
SSM2142
THD PERFORMANCE
The following data, taken from the THD test circuit on an
Audio Precision System One using the internal 80 kHz noise
filter, demonstrates the typical performance of a balanced pair
system based on the SSM2142/SSM2141 chip set. Both dif-
ferential and single-ended modes of operation are shown, under
a number of output load conditions which simulate various
application situations. Note also that there is no adverse effect
on system performance when using the optional series feedback
capacitors, which reject dc cable offsets in order to maintain
optimal ac noise rejection. The large signal transient response of
the system to a 100 kHz square wave input is also shown,
demonstrating the stability of the SSM2142 under load.IN
+18V
–18V
10µF*
10µF*R1R2VOUT
*USED ONLY IN THD PLOTS AS NOTED.
ALL CABLE MEASUREMENTS USE BELDEN 8451 CABLE.
Figure 7.THD Test Circuit
Figure 8.THD+N vs. Frequency at Point B
(Differential Mode)
Figure 9.THD+N vs. Frequency at Point B
(Differential Mode)
Figure 10.THD+N vs. Frequency at Point A
(Single Ended)
Figure 11.THD+N vs. Frequency at Point C
on-chip 50 Ω series damping resistors. The impedances in the
output buffer pair are precisely balanced by laser trimming
during production. This results in the high gain accuracy
needed to obtain good common-mode noise rejection, and
excellent separation between the offset error voltages common
to the cable pair and the desired differential input signal. As
shown in the test circuit, it is suggested that a suitable balanced,
high input-impedance differential amplifier such as the
SSM2141 be used at the receiving end for best system
performance. The SSM2141 receiver output is configured for a
gain of one half following the 6 dB gain of the SSM2142, in
order to maintain an overall system gain of unity.
In applications encountering a large dc offset on the cable or
those wishing to ensure optimal rejection performance by
avoiding differential offset error sources, dc blocking capacitors
may be employed at the sense outputs of the SSM2142. As
shown in the test circuit, these components should present as
little impedance as possible to minimize low-frequency errors,
such as 10 μF NP (or tantalum if the polarity of the offset is
known).
SYSTEM GROUNDING CONSIDERATIONS
Due to ground currents, supply variations, and other factors,
the ground potentials of the circuits at each end of a signal cable
may not be exactly equal. The primary purpose of a balanced
pair line is to reject this voltage difference, commonly called
“longitudinal error.” A measure of the ability of the system to
reject longitudinal error voltage is output common-mode
rejection. In order to obtain the optimal OCMR and noise
rejection performance available with the SSM2142, the user
should observe the following precautions:The quality of the differential output is directly dependent
upon the accuracy of the input voltage presented to the
device. Input voltage errors developed across the impedance
of the source must be avoided in order to maintain system
performance. The input of the SSM2142 should be driven
directly by an operational amplifier or buffer offering low
source impedance and low noise.The ground input should be in close proximity to the single-
ended input’s source common. Ground offset errors encoun-
tered in the source circuitry also impair system performance.Make sure that the SSM2142 is adequately decoupled with
0.1 μF bypass capacitors located close to each supply pin.Avoid the use of passive circuitry in series with the SSM2142
outputs. Any reactive difference in the line pair will cause
significant imbalances and affect the gain error of the device.
Snubber networks or series load resistors are not required to
maintain stability in SSM2142 based systems, even when
driving signals over extremely long cables.Efforts should be made to maintain a physical balance in the
arrangement of the signal pair wiring. Capacitive differences
due to variations in routing or wire length may cause unequal
noise pickup between the pair, which will degrade the system
OCMR. Shielded twisted-pair cable is the preferred choice in
all applications. The shield should not be utilized as a signal
conductor. Grounding the shield at one end, near the output
Figure 12.100 kHz Square Wave Observed at Point B
(Differential Mode). VO = 10 V rms, R1 = R2 = ∞, RL = 600 Ω
Figure 13.100 kHz Square Wave at Point B (Differential
Mode). VO = 10 V rms, R1 = R2 = ∞, RL = 600 Ω, with
Series Feedback CapacitorsIN
+15V
–15V3
+15V
–15V
SHIELDED
TWISTED-PAIR
CABLE
Figure 14.Typical Application of the SSM2142 and
SSM2141
APPLICATIONS INFORMATION
The SSM2142 is designed to provide excellent common-mode
rejection, high output drive, and low signal distortion and noise
in a balanced line-driving system. The differential output stage
consists of twin cross-coupled unity gain buffer amplifiers with
SSM2142
C1496–15–1/91
PRINTED IN U.S.A.
THE CABLE PAIR
The SSM2142 is capable of driving a 10 V rms signal into
600 Ω and will remain stable despite cable capacitances of up to
0.16 μF in either balanced or single-ended configurations. Low
impedance shielded audio cable such as the standard Belden
8451 or similar is recommended, especially in applications
traversing considerable distances. The user is cautioned that the
so-called “audiophile” cables may incur four times the capac-
itance per unit length of the standard industrial-grade product.
In situations of extreme load and/or distance, adding a second
parallel cable allows the user to trade off half of the total line
resistance against a doubling in capacitive load.
SINGLE-ENDED OPERATION
The SSM2142 is designed to be compatible with existing
balanced-pair interface systems. Just as in transformer-based
circuits, identical but opposite currents are generated by the
output pair which can be ground-referenced if desired and
transmitted on a single wire. Single-ended operation requires
that the unused side of the output pair be grounded to a solid
return path in order to avoid voltage offset errors at the nearby
input common. The signal quality obtained in these systems is
directly dependent on the quality of the ground at each end of
the wire. Also note that in single-ended operation the gain
through the device is still 6 dB, and that the SSM2142 incurs
no significant degradation in signal distortion or output drive
capability, although the noise rejection inherent in balanced-
pair systems is lost.
POWER SUPPLY SEQUENCING
A problem occasionally encountered in the interface system en-
vironment involves irregular application of the supplies. The
user is cautioned that applying power erratically can inadvert-
ently bias parts of the circuit into a latch-up condition. The
small geometries of an integrated circuit are easily breached and
damaged by short-risetime spikes on a supply line, which usu-
ally demonstrate considerable overshoot. The questionable
practice of exchanging components or boards while under
power can create such an undesirable sequence as well. Possible
options which offer improved board-level device protection
include: additional bypass capacitors, high-current reverse-
biased steering diodes between both supplies and ground, vari-
ous transient surge suppression devices, and safety grounding
connectors.
Likewise, power should be applied to the device before the
output is connected to “live” systems which may carry voltages
of sufficient magnitude to turn on the output devices of the
SSM2142 and damage the device. In any case, of course, the
user must always observe the absolute maximum ratings shown
in the specifications.
OUTLINE DIMENSIONS
Dimensions shown in inches and (mm).
8-Lead Plastic DIP
8-Lead Cerdip
16-Lead Small Outline (SOIC)

Partno	Mfg	Dc	Qty	Available	Descript
SSM2142S	ADI	N/a	3172	avai	Balanced Line Driver
SSM2142P	AD	N/a	471	avai	Balanced Line Driver