SN75LBC241DW ,Low-Power LinBiCMOS Multiple Drivers And Receiversmaximum ratings” may cause permanent damage to the device. These are stress ratings only, andfuncti ..
SN75LBC241DWR ,Low-Power LinBiCMOS Multiple Drivers And Receiversmaximum ratings over operating free-air temperature range (unless otherwise noted)Input supply volt ..
SN75LBC771DW ,GeoPort(TM) Transceiverlogic diagram (positive logic)GeoPort Peripheral (DCE) Interface Device* Uses LinBiCMOS Process Te ..
SN75LBC776DBR ,Single-Chip GeoPort(TM) Transceiver SN75LBC776 SINGLE-CHIP GeoPort TRANSCEIVER SLLS221B – NOVEMBER 1995 – REVISED MARCH 2002DB or DW ..
SN75LBC777DW , SINGLE CHIP GEOPORTE/AppleTalkE TRANSCEIVER
SN75LBC968DL ,9-Channel Bus Transceiver With Active Terminationmaximum ratings over operating free-air temperature range (unless otherwise noted)Supply voltage ra ..
SPM5030T-R20M , Inductors for Power Circuits Wound Metallic Magnetic Material SPM series
SPN02N60C3 ,for lowest Conduction Losses & fastest SwitchingFeaturesV @ T 650 VDS j,max• New revolutionary high voltage technologyR 2.5ΩDS(on),max• Ultra low g ..
SPN1423S32RG , N-Channel Enhancement Mode MOSFET
SPN2302AS23RG , N-Channel Enhancement Mode MOSFET
SPN2302AS23RG , N-Channel Enhancement Mode MOSFET
SPN2308S23RG , N-Channel Enhancement Mode MOSFET
SN75LBC241-SN75LBC241DW-SN75LBC241DWR
Low-Power LinBiCMOS Multiple Drivers And Receivers
MAX241 Operates at Data Rates up to 100 kbit/s
Over a 3-m Cable Low-Power Shutdown Mode ... ≤1 μA Typ LinBiCMOS Process Technology Four Drivers and Five Receivers ±30-V Input Levels
3-State TTL/CMOS Receiver Outputs ±9-V Output Swing With a 5-V Supply
Applications
– TIA/EIA-232-F Interface
– Battery-Powered Systems
– Terminals
– Modems
– Computers Packaged in Plastic Small-Outline Package
descriptionThe SN75LBC241 is a low-power LinBiCMOS line-interface device containing four independent drivers and
five receivers. It is designed as a plug-in replacement for the Maxim MAX241. The SN75LBC241 provides a
capacitive-charge-pump voltage generator to produce RS-232 voltage levels from a 5-V supply. The
charge-pump oscillator frequency is 20 kHz. Each receiver converts RS-232 inputs to 5-V TTL/CMOS levels.
The receivers have a typical threshold of 1.2 V and a typical hysteresis of 0.5 V and can accept ±30-V inputs.
Each driver converts TTL/CMOS input levels into RS-232 levels.
The SN75LBC241 includes a receiver, a 3-state control line, and a low-power shutdown control line. When the
EN line is high, receiver outputs are placed in the high-impedance state. When EN is low, normal operation is
enabled.
The shutdown mode reduces power dissipation to less than 5 μW, typically. In this mode, receiver outputs have
high impedance, driver outputs are turned off, and the charge-pump circuit is turned off. When SHUTDOWN
is high, the shutdown mode is enabled. When SHUTDOWN is low, normal operation is enabled.
This device has been designed to conform to TIA/EIA-232-F and ITU Recommendation V.28.
The SN75LBC241 has been designed using LinBiCMOS technology and cells contained in the
Texas Instruments LinASIC library. Use of LinBiCMOS circuitry increases latch-up immunity in this device
over an all-CMOS design.
The SN75LBC241 is characterized for operation from 0°C to 70°C.
TOUT2
RIN2
ROUT2
TIN2
TIN1
ROUT1
RIN1
GNDCC
C1+
VDD
C1–
ROUT3
SHUTDOWN
RIN4
ROUT4
TIN4
TIN3
ROUT5
RIN5
VSS
C2–
C2+
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
