SN75ALS193DRG4 ,Quadruple Differential Line Receiver 16-SOIC 0 to 70features 3-state outputs thatpermit direct connection to a bus-organized system with a fail-safe de ..
SN75ALS193J ,Quadruple Differential Line Receivermaximum ratings over operating free-air temperature range (unless otherwise noted)Supply voltage, V ..
SN75ALS193N ,Quadruple Differential Line Receiverfeatures high input impedance, input hysteresis for increased noise immunity, and an input sensitiv ..
SN75ALS194 ,Quadruple Differential Line Driverlogic diagram (positive logic)44EN1, 2EN1, 2EN21Y1 21Y1A3 11A1Z31Z67 2Y2A 5 62Y2Z72A52Z12EN3, 4EN12 ..
SN75ALS194D ,Quadruple Differential Line Driver SN55ALS194, SN75ALS194 QUADRUPLE DIFFERENTIAL LINE DRIVERS SLLS009D – OCTOBER 1985 – REVISED MAY 1 ..
SN75ALS194N ,Quadruple Differential Line Drivermaximum ratings” may cause permanent damage to the device. These are stress ratings only, andfuncti ..
SPI07N60C3 ,for lowest Conduction Losses & fastest SwitchingCharacteristicsParameter Symbol Values Unitmin. typ. max.R - - 1.5 K/WThermal resistance, junction ..
SPI08N50C3 ,for lowest Conduction Losses & fastest SwitchingCharacteristics, at T =25°C unless otherwise specifiedjParameter Symbol Conditions Values Unitmin. ..
SPI08N80C3 ,for lowest Conduction Losses & fastest SwitchingPlease note: Infineon has changed the CoolMOS 800V C2 marking to C3. 800V C2 ...FeatureR 0.65 ΩDS(on)• New revolutionary high voltage technologyI 8 AD• Ultra low gate chargeP-TO22 ..
SPI11N60C3 ,for lowest Conduction Losses & fastest SwitchingCharacteristicsParameter Symbol Conditions Values Unitmin. typ. max.Transconductance g V ≥2*I *R , ..
SPI11N60S5 ,for lowest Conduction LossesFeatureR 0.38 ΩDS(on)• New revolutionary high voltage technologyI 11 AD• Ultra low gate chargeP-TO2 ..
SPI11N65C3 ,for lowest Conduction Losses & fastest SwitchingCharacteristicsParameter Symbol Values Unitmin. typ. max.R - - 1 K/WThermal resistance, junction - ..
SN75ALS193DRG4-SN75ALS193J-SN75ALS193N
Quadruple Differential Line Receiver
3-State Outputs Common-Mode Input Voltage Range–7 V to 7 V Input Sensitivity... ±200 mV
Input Hysteresis... 120 mV Typ High Input Impedance...12 kΩ Min Operates from Single 5-V Supply Low Supply Current Requirement
35 mA Max Improved Speed and Power Version of the
AM26LS32A
descriptionThe SN75ALS193 is a monolithic quadruple line receiver with 3-state outputs designed using advanced
low-power Schottky technology. This technology provides combined improvements in bar design, tooling
production, and wafer fabrication. This, in turn, provides significantly lower power requirements and permits
much higher data throughput than other designs. This device meets the specifications of ANSI Standards
EIA/TIA-422-B and EIA/TIA-423-A and ITU Recommendations V.10 and V.11. It features 3-state outputs that
permit direct connection to a bus-organized system with a fail-safe design that ensures the outputs will always
be high if the inputs are open.
The device is optimized for balanced multipoint bus transmission at rates up to 20 megabits per second. The
input features high input impedance, input hysteresis for increased noise immunity, and an input sensitivity of 200 mV over a common-mode input voltage range of –7 to 7 V. It also features active-high and active-low
enable functions that are common to the four channels. The SN75ALS193 is designed for optimum performance
when used with the ’ALS192 quadruple differential line driver.
The SN75ALS193 is characterized for operation from 0°C to 70°C.
FUNCTION TABLE
(each receiver)H = high level, L = low level, X = irrelevant, ? = indeterminate,
Z = high impedance (off)
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
GND
