SN75ALS085DW ,LAN Access Unit Interface Dual Driver/Receiver SN75ALS085 LAN ACCESS UNIT INTERFACE DUAL DRIVER/RECEIVER SLLS054D – APRIL 1989 – REVISED OCTOBER ..
SN75ALS1177 ,Dual Differential Drivers And Receivers SN75ALS1177, SN75ALS1178 DUAL DIFFERENTIAL DRIVERS AND RECEIVERS SLLS154B – MARCH 1993 – REVISED F ..
SN75ALS1177N ,Dual Differential Drivers And Receiverslogic diagram (positive logic)SN75ALS1177 SN75ALS11784121DEDE141Y151D1341ZRE21A3141R1Y 1151B1D 1312 ..
SN75ALS1177NS , DUAL DIFFERENTIAL DRIVERS AND RECEIVERS
SN75ALS1177NSR ,Dual Differential Drivers And Receiversmaximum ratings over operating free-air temperature range (unless otherwise noted)Supply voltage, V ..
SN75ALS1177NSRG4 , DUAL DIFFERENTIAL DRIVERS AND RECEIVERS
SPI07N60C3 ,for lowest Conduction Losses & fastest SwitchingCharacteristicsParameter Symbol Values Unitmin. typ. max.R - - 1.5 K/WThermal resistance, junction ..
SPI08N50C3 ,for lowest Conduction Losses & fastest SwitchingCharacteristics, at T =25°C unless otherwise specifiedjParameter Symbol Conditions Values Unitmin. ..
SPI08N80C3 ,for lowest Conduction Losses & fastest SwitchingPlease note: Infineon has changed the CoolMOS 800V C2 marking to C3. 800V C2 ...FeatureR 0.65 ΩDS(on)• New revolutionary high voltage technologyI 8 AD• Ultra low gate chargeP-TO22 ..
SPI11N60C3 ,for lowest Conduction Losses & fastest SwitchingCharacteristicsParameter Symbol Conditions Values Unitmin. typ. max.Transconductance g V ≥2*I *R , ..
SPI11N60S5 ,for lowest Conduction LossesFeatureR 0.38 ΩDS(on)• New revolutionary high voltage technologyI 11 AD• Ultra low gate chargeP-TO2 ..
SPI11N65C3 ,for lowest Conduction Losses & fastest SwitchingCharacteristicsParameter Symbol Values Unitmin. typ. max.R - - 1 K/WThermal resistance, junction - ..
SN75ALS085DW
LAN Access Unit Interface Dual Driver/Receiver
Receiver Inputs Drives a Balanced 78-Ω Load Transformer Coupling Not Required in
System Power-Up/Power-Down Protection (Glitch
Free) Isolated Ground Pins for Reduced Noise
Coupling Fault-Condition Protection Built Into the
Device Driver Inputs Are Level-Shifted ECL
Compatible Package Options Include Plastic
Small-Outline (DW) Package and Standard
Plastic (NT) DIP
descriptionThe SN75ALS085 is a high-speed, advanced low-power Schottky, dual-channel driver/receiver device
designed for use in the AUI of ANSI/IEEE Std 802.3-1988. The two drivers on the device drive a 78-Ω balanced,
terminated twisted-pair transmission line up to a maximum length of 50 meters. In the off (idle) state, the drivers
maintain minimal differential output voltage on the twisted-pair line and, at the same time, remain within the
required output common-mode range.
With the driver enable (TXEN) high, upon receiving the first falling edge into the driver input, the differential
outputs rise to full-amplitude output levels within 25 ns. The output amplitude is maintained for the remainder
of the packet. After the last positive packet edge is transmitted into the driver, the driver maintains a minimum
of 70% full differential output for a minimum of 200 ns, then decays to a minimum level for the reset (idle)
condition within 8 μs. Disabling the driver by taking the driver enable low also forces the output into the idle
condition after the normal 8-μs timeout. While operating, the drivers are able to withstand a set of fault conditions
and not suffer damage due to the faults being applied. The drivers power up in the idle state to ensure that no
activity is placed on the twisted-pair cable, which could be interpreted as network traffic.
The line receiver squelch function interfaces to a differential twisted-pair line terminated external to the device.
The receiver squelch circuit allows differential receive signals to pass through, as long as the input amplitude
and pulse duration are greater than the minimum squelch threshold. This ensures a good signal-to-noise ratio
while the data path is active and prevents system noise from causing false data transitions during line shutdown
and line-idle conditions. The receiver outputs (RXO) default to a high level and the receiver-enable (RXEN)
outputs default to a low level while the squelch function is blocking the data path through the receiver (idle). The
line receiver squelch becomes active within 50 ns when the input squelch threshold is exceeded. RXEN is driven
high when the squelch circuit allows data to pass through the receiver. The receiver squelch circuit also can
withstand a set of fault conditions while operating, without causing permanent damage to the device.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
