SN74LVCZ245APW ,Octal Bus Transceiver With 3-State Outputs SN74LVCZ245A OCTAL BUS TRANSCEIVERWITH 3-STATE OUTPUTSSCES275G – JUNE 1999 – REVISED AUGUST 2003DB ..
SN74LVCZ32240AGKER ,32-Bit Buffer/Driver with 3-State OutputsFEATURES• Member of the Texas Instruments Widebus+™ • Supports Mixed-Mode Signal Operation on AllFa ..
SN74LVT125D ,3.3-V ABT Quadruple Bus Buffers With 3-State Outputsmaximum ratings” may cause permanent damage to the device. These are stress ratings only, andfuncti ..
SN74LVT125DB , 3.3-V ABT QUADRUPLE BUS BUFFERS WITH 3-STATE OUTPUTS
SN74LVT125DBLE ,3.3-V ABT Quadruple Bus Buffers With 3-State Outputsfeatures independent line drivers with 3-state outputs. Each output is in the high-impedancestate w ..
SN74LVT125DBR ,3.3-V ABT Quadruple Bus Buffers With 3-State Outputs SCBS133F − MAY 1992 − REVISED OCTOBER 2003 ..
SP690TCN , 3.0V/3.3V Low Power Microprocessor Supervisory with Battery Switch-Over
SP690TCN , 3.0V/3.3V Low Power Microprocessor Supervisory with Battery Switch-Over
SP690TCN , 3.0V/3.3V Low Power Microprocessor Supervisory with Battery Switch-Over
SP690TEN , 3.0V/3.3V Low Power Microprocessor Supervisory with Battery Switch-Over
SP690TEN , 3.0V/3.3V Low Power Microprocessor Supervisory with Battery Switch-Over
SP691ACP , Low Power Microprocessor Supervisory with Battery Switch-Over
SN74LVCZ245APW
Octal Bus Transceiver With 3-State Outputs
<0.8 V at VCC = 3.3 V, TA = 25°C Typical VOHV (Output VOH Undershoot)
>2 V at VCC = 3.3 V, TA = 25°C Ioff and Power-Up 3-State Support Hot
Insertion Supports Mixed-Mode Signal Operation on
All Ports (5-V Input/Output Voltage With
3.3-V VCC) Latch-Up Performance Exceeds 100 mA Per
JESD 78, Class II
description/ordering informationThis octal bus transceiver is designed for 2.7-V to 3.6-V VCC operation.
The SN74LVCZ245A is designed for asynchronous communication between data buses. The device transmits
data from the A bus to the B bus or from the B bus to the A bus, depending on the logic level at the
direction-control (DIR) input. The output-enable (OE) input can be used to disable the device so the buses are
effectively isolated.
Inputs can be driven from either 3.3-V or 5-V devices. This feature allows the use of this device as a translator
in a mixed 3.3-V/5-V system environment.
When VCC is between 0 and 1.5 V, the device is in the high-impedance state during power up or power down.
However, to ensure the high-impedance state above 1.5 V, OE should be tied to VCC through a pullup resistor;
the minimum value of the resistor is determined by the current-sinking capability of the driver.
This device is fully specified for hot-insertion applications using Ioff and power-up 3-state. The Ioff circuitry
disables the outputs, preventing damaging current backflow through the device when it is powered down. The
power-up 3-state circuitry places the outputs in the high-impedance state during power up and power down,
which prevents driver conflict.
ORDERING INFORMATION Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines
are available at www.ti.com/sc/package.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
GND
