SN65LVDS34DRG4 ,Dual LVDS Receiver with -4 to 5V Common-mode Range 8-SOIC -40 to 85.(2) Add the suffix R for taped and reeled carrier.DESCRIPTION (CONTINUED)The receivers can withsta ..
SN65LVDS386DGG ,16-Channel LVDS Receiver SLLS394I–SEPTEMBER 1999–REVISED DECEMBER 20145 Description (Continued)Any of the differential rece ..
SN65LVDS386DGGRG4 ,16-Channel LVDS Receiver 64-TSSOP -40 to 85electrical characteristics of low-voltage differentialRequirements of ANSI TIA/EIA-644 Standardsign ..
SN65LVDS387DGG ,16-Channel LVDS Driverelectrical characteristics of low-Drivers Meet or Exceed the Requirements of ANSIvoltage differenti ..
SN65LVDS387DGGR ,16-Channel LVDS Driver SLLS362G–SEPTEMBER 1999–REVISED JANUARY 20165 Description (Continued)When disabled, the driver out ..
SN65LVDS387DGGRG4 ,16-Channel LVDS Driver 64-TSSOP -40 to 85Electrical Characteristics ...... 714.3 Related Links.. 258.6 Switching Characteristics...... 814.4 ..
SN74HCT04DR ,Hex Inverterslogic diagram (positive logic)AY†absolute
SN74HCT04DRG4 ,Hex Inverters 14-SOIC -40 to 85 SN54HCT04, SN74HCT04 HEX INVERTERS SCLS042D – JULY 1986 – REVISED JULY 2003* Operating Voltage Ran ..
SN74HCT04N ,Hex Invertersmaximum ratings over operating free-air temperature range (unless otherwise noted)Supply voltage ra ..
SN74HCT04NSR ,Hex Inverters/sc/package.FUNCTION TABLE(each inverter)INPUT OUTPUTA YH LL HPlease be aware that an important not ..
SN74HCT04PW ,Hex Invertersmaximum ratings” may cause permanent damage to the device. These are stress ratings only, andfuncti ..
SN74HCT04PWR ,Hex Invertersmaximum ratings” may cause permanent damage to the device. These are stress ratings only, andfuncti ..
SN65LVDS34DR-SN65LVDS34DRG4
Dual LVDS Receiver with -4 to 5V Common-mode Range
SN65LVDS33, SN65LVDT33 SN65LVDS34, SN65LVDT34 www.ti.com SLLS490B –MARCH 2001–REVISED NOVEMBER 2004 HIGH-SPEED DIFFERENTIAL RECEIVERS Check for Samples: SN65LVDS33, SN65LVDT33, SN65LVDS34, SN65LVDT34 1 The high-speed switching of LVDS signals usually FEATURES (1) necessitates the use of a line impedance matching • 400-Mbps Signaling Rate and 200-Mxfr/s resistor at the receiving-end of the cable or Data Transfer Rate transmission media. The SN65LVDT series of • Operates With a Single 3.3-V Supply receivers eliminates this external resistor by integrating it with the receiver. The nonterminated • -4 V to 5 V Common-Mode Input Voltage SN65LVDS series is also available for multidrop or Range other termination circuits. • Differential Input Thresholds <±50 mV With 50 mV of Hysteresis Over Entire Common-Mode SN65LVDS33D, SN65LVDT33D Input Voltage Range SN65LVDS33PW, SN65LVDT33PW • Integrated 110-Ω Line Termination Resistors D OR PW PACKAGE logic diagram (positive logic) On LVDT Products (TOP VIEW) • TSSOP Packaging (33 Only) G 1B 1 16 V • Complies With TIA/EIA-644 (LVDS) CC G 1A 2 15 4B SN65LVDT33 ONLY • Active Failsafe Assures a High-Level Output 1Y 4A 3 14 1A With No Input 1Y G 4 13 4Y • Bus-Pin ESD Protection Exceeds 15 kV HBM 1B 2Y 5 12 G • Input Remains High-Impedance on Power 2A 6 11 3Y 2A Down 2B 7 10 3A 2Y • TTL Inputs Are 5 V Tolerant 2B GND 8 9 3B • Pin-Compatible With the AM26LS32, 3A SN65LVDS32B,µA9637, SN65LVDS9637B 3Y 3B (1) The signalling rate of a line, is the number of voltage transitions that are made per second expressed in the units 4A bps (bits per second). 4Y 4B DESCRIPTION SN65LVDS34D, SN65LVDT34D This family of four LVDS data line receivers offers the widest common-mode input voltage range in the D PACKAGE (TOP VIEW) logic diagram (positive logic) industry. These receivers provide an input voltage range specification compatible with a 5-V PECL V 1 8 1A signal as well as an overall increased ground-noise CC 1A 1Y 2 7 1B tolerance. They are in industry standard footprints 1Y with integrated termination as an option. 2Y 3 6 2A 1B SN65LVDT34 ONLY GND 4 5 2B Precise control of the differential input voltage 2A thresholds allows for inclusion of 50 mV of input 2Y voltage hysteresis to improve noise rejection on 2B slowly changing input signals. The input thresholds are still no more than ±50 mV over the full input common-mode voltage range. 1 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PRODUCTION DATA information is current as of publication date. Copyright © 2001–2004, Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters.
