SI9160 ,Controller for RF Power Amplifier Boost ConverterSi9160 Vishay SiliconixPortable Communications and PC Card Converters Si9160Controller for RF Power ..
SI9161 ,Optimized-Efficiency Controller for RF Power Amplifier Boost ConverterFEATURES• Si9160 architecture optimized for “light-load” efficiency • Standby Mode• High Frequency ..
SI9166 ,High Frequency Programmable Topology ControllerAbsolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, ..
SI9169BQ-T1 ,High Frequency 1-A Synchronous Buck/Boost ConverterS-40695—Rev. D, 19-Apr-042Si9169Vishay SiliconixSPECIFICATIONST Test Conditions est ConditionseLimi ..
SI9175DH-T1 , High Performance Step-Down DC-DC Converter With Adjustable Output Voltage
SI9175DM-T1 , High Performance Step-Down DC-DC Converter With Adjustable Output Voltage
SM150A , Schottky Barrier Rectifiers Reverse Voltage 20 to100V Forward Current 1.0A
SM15T100A ,TRANSILFEATURESn PEAK PULSE POWER : 1500 W (10/1000μs)n BREAKDOWN VOLTAGE RANGE :From 6.8 V to 220 Vn UNI ..
SM15T100CA ,TRANSILSM15T6V8A/220A®SM15T6V8CA/220CATMTRANSIL
SM15T100CA ,TRANSILFEATURESn PEAK PULSE POWER : 1500 W (10/1000μs)n BREAKDOWN VOLTAGE RANGE :From 6.8 V to 220 Vn UNI ..
SM15T10A ,TRANSZORB SURFACE MOUNT TRANSIENT VOLTAGE SUPPRESSORABSOLUTE MAXIMUM RATINGS (T = 25°C)ambSymbol Parameter Value UnitP Peak pulse power dissipation (se ..
SM15T10A ,TRANSZORB SURFACE MOUNT TRANSIENT VOLTAGE SUPPRESSORSM15T6V8A/220A®SM15T6V8CA/220CATMTRANSIL
SI9160
Controller for RF Power Amplifier Boost Converter
Si9160 Vishay Siliconix
Controller for RF Power Amplifier Boost Converter
FEATURES
DESCRIPTIONThe Si9160 Controller for RF Power Amplifier Boost Converter
is a fixed-frequency, pulse-width-modulated power conversion
controller designed for use with the Si6801 application
specific MOSFET. The Si9160 and the Si6801 are optimized
for high efficiency switched-mode power conversion at 1 MHz
and over. The device has an enable pin which can be used to
put the converter in a low-current mode compatible with the
standby mode of most cellular phones. A wide bandwidth
feedback amplifier minimizes transient response time allowing
the device to meet the instantaneous current demands of
today’s digital protocols. The input voltage range
accommodates minimal size and cost battery pack
configurations.
Frequency control in switching is important to noise
management techniques in RF communications. The Si9160
is easily synchronized for high efficiency power conversion at
frequencies in excess of 1 MHz.
Optimizing the controller and the synchronous FETs results in
the highest conversion efficiency over a wide load range at the
switching frequencies of interest (1 MHz or greater). It also
minimizes the overshoot and gate ringing associated with
drive current and gate charge mismatches.
When disabled, the converter requires less than 330 μA. This
capability minimizes the impact of the converter on battery life
when the phone is in the standby mode.
Finally, operating voltage is optimized for LiIon battery
operation (2.7 V to 4.5 V) and can also be used with three-cell
NiCd or NiMH (3 V to 3.6 V), as well as four-cell NiCd or NiMH
(4 V to 4.8 V) battery packs.
APPLICATION CIRCUIT High Frequency Switching (up to 2 MHz) Optimized Output Drive Current (350 mA) Standby Mode Wide Bandwidth Feedback Amplifier Single-Cell LiIon and Three-cell NiCd or NiMH Operation
Si9160Portable Communications and PC Card Converters
