MC145583VF ,3.3 Volt Only Driver/Receiver with an Integrated Standby ModeMAXIMUM RATINGS (Voltage polarities referenced to GND)This device contains protection circuitry toR ..
MC145583VF. ,3.3 Volt Only Driver/Receiver with an Integrated Standby Modeelectrical specifications of EIA–232–E, EIA–562, andORDERING INFORMATIONCCITT V.28 while operating ..
MC14558BCP ,BCD-to-Seven Segment DecoderMaximum Ratings are those values beyond which damage to the device may occur.V 8 9 e†Temperature De ..
MC14558BD ,BCD-to-Seven Segment DecoderMAXIMUM RATINGS* (Voltages referenced to V )SSPIN ASSIGNMENT Rating Symbol Value UnitB 1 16 VDDDC S ..
MC14559B ,Successive Approximation Registers3MC14549B, MC14559B(6.)ÎÎÎÎÎ SWITCHING CHARACTERISTICS (C = 50 pF, T = 25C)L AÎÎÎÎÎ Characteristi ..
MC14559B ,Successive Approximation RegistersELECTRICAL CHARACTERISTICS (Voltages Referenced to V )SSÎÎÎÎÎ – 55C 25C 125CV VDD DD(3.)Vdc Min ..
MC74AC244DT ,Octal Buffer/Line Driver with 3 State Outputs* ** ** OCTAL BUFFER/LINEDRIVER WITH* * *3-STATE OUTPUTSThe MC74AC244/74ACT244 is an octal buffer ..
MC74AC244DW ,OCTAL BUFFER/LINE DRIVER WITH 3-STATE OUTPUTS* ** ** OCTAL BUFFER/LINEDRIVER WITH* * *3-STATE OUTPUTSThe MC74AC244/74ACT244 is an octal buffer ..
MC74AC244DWR2 ,Octal Buffer/Line Driver with 3 State OutputsMaximum Ratings are those values beyond which damage to the device may occur. Functional operation ..
MC74AC244DWR2G , Octal Buffer/Line Driver with 3−State Outputs
MC74AC244MEL ,Octal Buffer/Line Driver with 3 State OutputsMAXIMUM RATINGS*Symbol Parameter Value UnitV DC Supply Voltage (Referenced to GND) –0.5 to +7.0 VCC ..
MC74AC244ML1 ,Octal Buffer/Line Driver with 3 State OutputsMAXIMUM RATINGS*Symbol Parameter Value UnitV DC Supply Voltage (Referenced to GND) –0.5 to +7.0 VCC ..
MC145583VF-MC145583VF.
3.3 Volt Only Driver/Receiver with an Integrated Standby Mode
Product Preview #
!! " -
# -
EIA–232–E and CCITT V.28The MC145583 is a CMOS transceiver composed of three drivers and five
receivers that fulfills the electrical specifications of EIA–232–E, EIA–562, and
CCITT V.28 while operating from a single + 3.3 or + 5.0 V power supply. This
transceiver is a high–performance, low–power consumption device that is
equipped with a standby function.
A voltage tripler and inverter converts the + 3.3 V to ± 8.8 V, or a voltage
doubler and inverter converts the + 5.0 V to ± 8.8 V. This is accomplished
through an on–chip 40 kHz oscillator and five inexpensive external capacitors.
Drivers: ± 5 V Minimum Output Swing at 3.3 or 5.0 V Power Supply 300 Ω Power–Off Impedance Output Current Limiting Three–State Outputs During Standby Mode
Receivers: ± 25 V Input Range 3 to 7 kΩ Input Impedance 0.8 V Hysteresis for Enhanced Noise Immunity Three–State Outputs During Standby Mode
Ring Monitor Circuit: Invert the Input Level on Rx1 to Logic Output Level on RIMON at Standby
Mode
This document contains information on a product under development. Motorola reserves the right to change or discontinue this product without notice.
Order this document
by MC145583/D-
SEMICONDUCTOR TECHNICAL DATA
