MC12095D ,2.5 GHz Low Power Prescaler With Stand-By ModeOrder this document by MC12095/D * ** ** * ** *The MC12095 is a single modulus prescaler for low ..
MC12095DR2 ,2.5 GHz Low Power Prescaler With Stand-By ModeMOSAIC V technology is utilized to achieve low power dissipationof 24 mW at a minimum supply volta ..
MC12100 ,200 MHz VOLTAGE CONTROLLED MULTIVIBRATOROrder this document by MC12100/D* * **• High Frequency VCM Ideal for PLL Applications200 MHz VOLT ..
MC12101 ,130 MHz VOLTAGE CONTROLLED MULTIVIBRATOROrder this document by MC12101/D* * **• High Frequency VCM Ideal for PLL Applications130 MHz VOLT ..
MC12147 ,LOW POWER VOLTAGE CONTROLLED OSCILLATOR BUFFEROrder this document by MC12147/D* ** ** * The MC12147 is intended for applications requiring high ..
MC12149D ,LOW POWER VOLTAGE CONTROLLED OSCILLATOR BUFFEROrder this document by MC12149/D* ** * ** ** *LOW POWERThe MC12149 is intended for applications req ..
MC54F00J ,QUAD 2-INPUT NAND GATE FAST SCHOTTKY TTL
MC54F04J ,HEX INVERTER FAST SCHOTTKY TTL
MC54F08J ,QUAD 2-INPUT AND GATE FAST SCHOTTKY TTL
MC54F138J ,1-of-8 decoder/demultiplexerLOGIC DIAGRAMMC54FXXXJ CeramicE E EA A A2 1 0 1 2 3MC74FXXXN PlasticV = PIN 16CC3 2 1 MC74FXXXD SOI ..
MC54F14J ,SCHMITT TRIGGERS DUAL 4-INPUT NAND/HEX INVERTERS FAST SCHOTTKY TTL
MC54F153J ,DUAL 4-INPUT MULTIPLEXERLOGIC DIAGRAMN SUFFIXE I I I I S S I I I I E PLASTICa 0a 1a 2a 3a 1 0 0b 1b 2b 3b bCASE 648-081 3 2 ..
MC12095D
MECL PLL COMPONENTS ?, ? LOW POWER PRESCALER WITH STAND-BY MODE
Order this document by MC12095/D
ORDERING INFORMATION - -
The MC12095 is a single modulus prescaler for low power frequency
division of a 2.5 GHz high frequency input signal. Motorola’s advanced
MOSAIC V technology is utilized to acheive low power dissipation of mW at a minimum supply voltage of 2.7 V.
On–chip output termination provides output current to drive a 2.0 pF
(typical) high impedance load. If additional drive is required for the prescaler
output, an external resistor can be added in parallel from the OUT pin to
GND to increase the output power. Care must be taken not to exceed the
maximum allowable current through the output.
Divide ratio control input (SW) selects the required divide ratio of ÷2 or ÷4.
Stand–By mode is available to reduce current drain to 100μA typical when
the standby pin SB is switched LOW disabling the prescaler. 2.5 GHz Toggle Frequency Supply Voltage 2.7 V to 5.5 Vdc Low Power 8.7 mA Typical Operating Temperature –40 to 85°C Divide by 2 or 4 Selected by the SW Pin
NOTE: For applications up to 1.1 GHz, please consult the MC12093datasheet.
MOSAIC V is a trademark of Motorola
FUNCTIONAL TABLE
NOTES: 1.SW: H = (VCC – 0.4 V) to VCC; L = OPEN
2.SB: H = 2.0 V to VCC; L = GND to 0.8 V
