MC12034AD ,MECL PLL COMPONENTS ?2/33, ?4/65 DUAL MODULUS PRESCALEROrder this document by MC12034A/D* * * The MC12034A can be used with CMOS synthesizers requiring po ..
MC12034AD ,MECL PLL COMPONENTS ?2/33, ?4/65 DUAL MODULUS PRESCALERMAXIMUM RATINGSCharacteristic Symbol Range Unit1 8 ININV 2 7NCPower Supply Voltage, Pin 2 V –0.5 to ..
MC12034AP ,MECL PLL COMPONENTS ?2/33, ?4/65 DUAL MODULUS PRESCALERMAXIMUM RATINGSCharacteristic Symbol Range Unit1 8 ININV 2 7NCPower Supply Voltage, Pin 2 V –0.5 to ..
MC12034AP ,MECL PLL COMPONENTS ?2/33, ?4/65 DUAL MODULUS PRESCALEROrder this document by MC12034A/D* * * The MC12034A can be used with CMOS synthesizers requiring po ..
MC12034BD ,MECL PLL COMPONENTS ?2/33, ?4/65 DUAL MODULUS PRESCALERELECTRICAL CHARACTERISTICS (V = 4.5 to 5.5 Vdc, T = –40 to 85°C, unless otherwise noted.)CC ACharac ..
MC12036AD ,MECL PLL COMPONENTS ?4/65, ?28/129 DUAL MODULUS PRESCALER WITH STAND-BY MODE**SEMICONDUCTOR TECHNICAL DATA**% *#** #*#! * *!* *"* *"**$ ** * *The MC12036 is a 1.1GHz ÷64/65, ..
MC54F00J ,QUAD 2-INPUT NAND GATE FAST SCHOTTKY TTL
MC54F04J ,HEX INVERTER FAST SCHOTTKY TTL
MC54F08J ,QUAD 2-INPUT AND GATE FAST SCHOTTKY TTL
MC54F138J ,1-of-8 decoder/demultiplexerLOGIC DIAGRAMMC54FXXXJ CeramicE E EA A A2 1 0 1 2 3MC74FXXXN PlasticV = PIN 16CC3 2 1 MC74FXXXD SOI ..
MC54F14J ,SCHMITT TRIGGERS DUAL 4-INPUT NAND/HEX INVERTERS FAST SCHOTTKY TTL
MC54F153J ,DUAL 4-INPUT MULTIPLEXERLOGIC DIAGRAMN SUFFIXE I I I I S S I I I I E PLASTICa 0a 1a 2a 3a 1 0 0b 1b 2b 3b bCASE 648-081 3 2 ..
MC12034AD-MC12034AP-MC12034BD
MECL PLL COMPONENTS ?2/33, ?4/65 DUAL MODULUS PRESCALER
-The MC12034A can be used with CMOS synthesizers requiring positive
edges to trigger internal counters such as Motorola’s MC145xxx series in a
PLL to provide tuning signals up to 2.0 GHz in programmable frequency
steps.
The MC12034B can be used with CMOS synthesizers requiring negative
edges to trigger internal counters such as Fujitsu’s MB87001.
A Divide Ratio Control (SW) permits selection of a 32/33 or 64/65 divide
ratio as desired.
The Modulus Control (MC) selects the proper divide number after SW has
been biased to select the desired divide ratio. 2.0 GHz Toggle Frequency Supply Voltage 4.5 to 5.5 V MC12034A for Positive Edge Triggered Synthesizers 12mA Maximum, –40 to 85°C, VCC = 5.5 Vdc Modulus Control Input is Compatible with Standard CMOS and TTL Low–Power 8.5 mA Typical
FUNCTIONAL TABLE
NOTES: 1.SW: H = VCC, L = Open. A logic L can also be applied by grounding this pin,
but this is not recommended due to increased power consumption.
2.MC: H = 2.0 V to VCC, L = GND to 0.8 V.
NOTE: *Equivalent to a two–input NAND gate.
MAXIMUM RATINGS
NOTES: 1.ESD data available upon request.
2.This device contains protection circuitry to guard against damage due to high
static voltages or electric fields. However, precautions must be taken to avoid
applications of any voltage higher than maximum rated voltages to this high
impedance circuit. For proper operation, Vin and Vout should be constrained
to the range GND ≤ (Vin or Vout) ≤ VCC.
