MC10SX1190DT ,Fibre Channel Coaxial Cable Driver and Loop Resillency Circuit2MC10SX1190DC CHARACTERISTICS (Note 1)-40°C 0°C 25°C 85°CSymbol Characteristic Min Typ Max Min Typ ..
MC1121DMR2 ,100mA Charge Pump Voltage Converter with Shutdown2MC1121APPLICATIONS INFORMATIONNegative Voltage ConverterThe oscillator runs at 10kHz (typical) whe ..
MC12002P ,ANALOG MIXEROrder this document by MC12002/D* **The MC12002 is a double balanced analog mixer, including an inp ..
MC12009 ,MECL PLL COMPONENTS DUAL MODULUS PRESCALERMaximum Ratings above which performance may beORDERING INFORMATIONdegraded)Operating Temperature Ra ..
MC12009P ,MECL PLL COMPONENTS DUAL MODULUS PRESCALEROrder this document by MC12009/D* * These devices are two–modulus prescalers which will divide by 5 ..
MC12011 ,MECL PLL COMPONENTS DUAL MODULUS PRESCALERLogic DiagramsMC12009MTTL E5 9MECLDQ Q1 D2 DQ3 toMTTL E4 10MTTLMECL E3 11 Trans–latorC Q1 C C Q3MEC ..
MC4558C ,Amplifiers and Comparators
MC4558C ,Amplifiers and Comparators
MC4558CD ,WIDE BANDWIDTH DUAL BIPOLAR OP-AMPSMAXIMUM RATINGS (T = +25°C, unless otherwise noted.)A 1Rating Symbol MC4558AC MC4558C UnitP1 SUFFIX ..
MC4558CDR2 ,Dual Wide Bandwidth Operational AmplifierELECTRICAL CHARACTERISTICS (V = 15 V, V = –15 V, T = 25°C, unless otherwise noted.)CC EE AInput Off ..
MC4558CDR2 ,Dual Wide Bandwidth Operational AmplifierMAXIMUM RATINGS (T = +25°C, unless otherwise noted.)A 1Rating Symbol MC4558AC MC4558C UnitP1 SUFFIX ..
MC4558CDT ,WIDE BANDWIDTH DUAL BIPOLAR OP-AMPSMC4558WIDE BANDWIDTHDUAL BIPOLAR OPERATIONAL AMPLIFIER ■ INTERNALLY COMPENSATED ■ SHORT-CIRCUI ..
MC10SX1190DT
Fibre Channel Coaxial Cable Driver and Loop Resillency Circuit
MC10SX1190
Fibre Channel Coaxial
Cable Driver and Loop
Resiliency Circuit
The MC10SX1190 is a differential receiver, differential transmitter
specifically designed to drive coaxial cables. It incorporates the output
cable drive capability of the MC10EP89 Coaxial Cable Driver with
additional circuitry to multiplex the output cable drive source between
the cable receiver or the local transmitter inputs. The multiplexer
control circuitry is TTL compatible for ease of operation.
The MC10SX1190 is useful as a bypass element for Fibre
Channel-Arbitrated Loop (FC-AL) or Serial Storage Architecture
(SSA) applications, to create loop style interconnects with fault
tolerant, active switches at each device node. This device is
particularly useful for back panel applications where small size is
desirable.
The EP89 style drive circuitry produces swings approximately 70%
larger than a standard PECL output. When driving a coaxial cable,
proper termination is required at both ends of the line to minimize
reflections. The 1.4V output swings allow for proper termination at
both ends of the cable, while maintaining the required swing at the
receiving end of the cable. Because of the larger output swings, the
QT, QT outputs are terminated into the thevenin equivalent of 50Ω to
VCC– 3.0V instead of 50Ω to VCC– 2.0V. 2.5 Gbps Operation 425ps Propagation Delay 1.4V Output Swing on the Cable Driving Output PECL Mode: 3.0V to 5.5V VCC, with VEE = 0V ECL Mode: 0V VCC, with VEE = –3.0V to –5.5V 75kΩ Internal Input Pull Down Resistors 2000 V H.B.M. ESD Protection, >100 V mm
VCC
VCC QR QR VEE DT DT VCC
VEE DR DR VCC VCC QT QT VEE
VBB VEE
SEL VCC
Figure 1. 20-Lead TSSOP Pinout: (Top View)
