MC10H188FN ,Hex Buffer with EnableLOGIC DIAGRAMPower Supply (V = 0) V –8.0 to 0 VdcXCC EEOUT92YInput Voltage (V = 0) V 0 to V Vdc 5CC ..
MC10H188FNR2 ,Hex Buffer with Enable2AN1406/Dreduced while maintaining acceptable manufacturing design. After all the inclusion of ECL ..
MC10H188FNR2 ,Hex Buffer with Enable
MC10H188L ,Hex Buffer with EnableMAXIMUM RATINGSCharacteristic Symbol Rating Unit
MC10H188M ,Hex Buffer with EnableELECTRICAL CHARACTERISTICS (V = –5.2 V ±5%) (See Note 1.)EE0° 25° 75°Symbol Characteristic Min Max ..
MC10H188M ,Hex Buffer with Enable2MC10H188PACKAGE DIMENSIONSPLCC–20FN SUFFIXPLASTIC PLCC PACKAGECASE 775–02ISSUE CM S S0.007 (0.180) ..
MC4024L ,DUAL VOLTAGE-CONTROLLED MULTIVIBRATORM04324M04024(8) MOTOROLADUAL VOLTAGE-CONTROLLED MULTIVIBRATORThe MC4324/4024 consists of two indepe ..
MC4024P ,DUAL VOLTAGE-CONTROLLED MULTIVIBRATORM04324M04024(8) MOTOROLADUAL VOLTAGE-CONTROLLED MULTIVIBRATORThe MC4324/4024 consists of two indepe ..
MC4044 ,PHASE-FREQUENCY DETECTORLOGIC DIAGRAMPhaseFrequencyDetector#1 . 2AmplifierPhase CD 12FrequencyDetector 9#2 . 6Vcc-- Pin 14G ..
MC4044L ,Phase-frequency detector(8) MOTOROLAPHASE-FREOUENCY DETECTORThe MC4344/4044 consists of two digital phase detectors, acharg ..
MC4044P ,Phase-frequency detectorLOGIC DIAGRAMPhaseFrequencyDetector#1 . 2AmplifierPhase CD 12FrequencyDetector 9#2 . 6Vcc-- Pin 14G ..
MC-405 , SMD LOW/MEDIUM-FREQUENCY CRYSTAL UNIT
MC10H188FN-MC10H188L-MC10H188P
Hex Buffer with Enable
SEMICONDUCTOR TECHNICAL DATA -
The MC10H188 is a high–speed Hex Buffer with a common Enable input.
When Enable is in the high–state, all outputs are in the low–state. When Enable
is in the low–state, the outputs take the same state as the inputs.
This MECL 10H part is a functional/pinout duplication of the standard MECL
10K family part, with 100% improvement in propagation delay and no increase
in power–supply current. Propagation Delay, 1.3 ns Typical Data–to–Output Power Dissipation 180 mW Typ/Pkg (No Load) Improved Noise Margin 150 mV (Over Operating Voltage and
Temperature Range) Voltage Compensated MECL 10K–Compatible
MAXIMUM RATINGS
ELECTRICAL CHARACTERISTICS (VEE = –5.2 V ±5%) (See Note)
AC PARAMETERS
NOTE:Each MECL 10H series circuit has been designed to meet the dc specifications shown in the test table,
after thermal equilibrium has been established. The circuit is in a test socket or mounted on a printed circuit
board and transverse air flow greater than 500 Ifpm is maintained. Outputs are terminated through a
50–ohm resistor to –2.0 volts.
DIP
PIN ASSIGNMENTVCC1
AOUT
BOUT
COUT
AIN
BIN
CIN
VEE
VCC2
FOUT
EOUT
DOUT
FIN
EIN
DIN
COMMON
Pin assignment is for Dual–in–Line Package.
For PLCC pin assignment, see the Pin Conversion
Tables on page 6–11 of the Motorola MECL Data
