MC10H160L ,12-Bit Parity Generator-CheckerMAXIMUM RATINGSV = PIN 13CC1Characteristic Symbol Rating UnitV = PIN 16CC24V = PIN 8Power Supply (V ..
MC10H160P ,12-Bit Parity Generator-Checker
MC10H160P ,12-Bit Parity Generator-CheckerMAXIMUM RATINGSV = PIN 13CC1Characteristic Symbol Rating UnitV = PIN 16CC24V = PIN 8Power Supply (V ..
MC10H161 ,Binary to 1-8 Decoder (Low)2AN1672/DSection 1: Translation Between Differently Supplied ECL Drivers and ReceiversTable 3. Tran ..
MC10H161FN ,Binary to 1-8 Decoder (Low)MAXIMUM RATINGS13 Q4Characteristic Symbol Rating UnitB912 Q5Power Supply (V = 0) V –8.0 to 0 VdcCC ..
MC10H161FNR2 ,Binary to 1-8 Decoder (Low)
MC3486 ,Quadruple Differential Line Receiver With 3-State OutputsMC3486 QUADRUPLE DIFFERENTIAL LINE RECEIVERWITH 3-STATE OUTPUTSSLLS097C – JUNE 1980 – REVISED FEBRU ..
MC3486D ,QUAD EIA-422/3 LINE RECEIVER WITH THREE-STATE OUPUTSMAXIMUM RATINGSMC3486Rating Symbol Value UnitPower Supply Voltage VCC 8.0 VdcInput Common Mode Volt ..
MC3486DR ,Quadruple Differential Line Receiver With 3-State OutputsMC3486 QUADRUPLE DIFFERENTIAL LINE RECEIVERWITH 3-STATE OUTPUTSSLLS097C – JUNE 1980 – REVISED FEBRU ..
MC3486N ,Quadruple Differential Line Receiver With 3-State OutputsMC3486 QUADRUPLE DIFFERENTIAL LINE RECEIVERWITH 3-STATE OUTPUTSSLLS097C – JUNE 1980 – REVISED FEBRU ..
MC3486NSR ,Quadruple Differential Line Receiver With 3-State Outputsmaximum ratings over operating free-air temperature range (unless otherwise noted)Supply voltage, V ..
MC3486P ,QUAD EIA-422/3 LINE RECEIVER WITH THREE-STATE OUPUTSfeatures include:0 Four Independent Receiver Chains D SUFFIXo Three-State Outputs PLASTIC PACKAGE a ..
MC10H160L-MC10H160P
12-Bit Parity Generator-Checker
SEMICONDUCTOR TECHNICAL DATA-
The MC10H160 is a 12–bit parity generator–checker. The output goes high
when an odd number of inputs are high providing the odd parity function.
Unconnected inputs are pulled to a logic low allowing parity detection and
generation for less than 12 bits. The MC10H160 is a functional pin duplication
of the standard 10K family part with 100% improvement in propagation delay
and no increase in power–supply current. Propagation Delay, 2.5 ns Typical Power Dissipation, 320 mW Typical Improved Noise Margin 150 mV (Over Operating Voltage and
Temperature Range) Voltage Compensated MECL 10K–Compatible
MAXIMUM RATINGS
ELECTRICAL CHARACTERISTICS (VEE = –5.2 V ±5%) (See Note)
AC PARAMETERS
NOTE:Each MECL 10H series circuit has been designed to meet the dc specifications shown in the test table,
after thermal equilibrium has been established. The circuit is in a test socket or mounted on a printed circuit
board and transverse air flow greater than 500 Ifpm is maintained. Outputs are terminated through a
50–ohm resistor to –2.0 volts.
DIP
PIN ASSIGNMENTVCC1
OUT
IN1
IN2
IN3
IN4
IN5
VEE
VCC2
IN12
IN11
IN10
IN9
IN8
IN7
IN6
Pin assignment is for Dual–in–Line Package.
For PLCC pin assignment, see the Pin Conversion
Tables on page 6–11 of the Motorola MECL Data
