MC10H145L ,16 x 4 Bit Register File (RAM)ELECTRICAL CHARACTERISTICS (V = –5.2 V ±5%) (See Note)EEX XDisabled H L0° 25° 75°Ch Characteristic ..
MC10H145P ,16 x 4 Bit Register File(RAM)MAXIMUM RATINGSCASE 775–02Characteristic Symbol Rating UnitPower Supply (V = 0) V –8.0 to 0 VdcCC E ..
MC10H158FN ,Quad 2-Input Multiplexer (Non-Inverting)** * ** ** * **The High Speed Solution for theCMOS/TTL Designer
MC10H158FNR2 ,Quad 2-Input Multiplexer (Non-Inverting)AN1672/DThe ECL Translator GuidePECL • LVPECL • NECL • TTL •LVTTL/LVCMOS • CMOS
MC10H158L ,Quad 2-Input MultiplexerELECTRICAL CHARACTERISTICS (V = –5.2 V ±5%)EE0° 25° 75°Characteristic Symbol Min Max Min Max Min Ma ..
MC10H158M ,Quad 2-Input Multiplexer (Non-Inverting)Prepared byCleon PettyAPPLICATION NOTETodd PearsonECL Applications EngineeringThis application note ..
MC3458 ,Amplifiers and Comparators
MC3458DR2 ,Dual, Low Power Operational AmplifierMAXIMUM RATINGSOutput A 1 8 VCCRating Symbol Value Unit2 7Output BPower Supply Voltages Vdc–Inputs ..
MC3458DR2 ,Dual, Low Power Operational AmplifierOrder this document by MC3458/D** ** ** *DUAL DIFFERENTIALUtilizing the circuit designs perfected ..
MC3458P1 ,DUAL DIFFERENTIAL INPUT OPERATIONAL AMPLIFIERSMAXIMUM RATINGSOutput A 1 8 VCCRating Symbol Value Unit2 7Output BPower Supply Voltages Vdc–Inputs ..
MC3458P1 ,DUAL DIFFERENTIAL INPUT OPERATIONAL AMPLIFIERSELECTRICAL CHARACTERISTICS (For MC3458, V = +15 V, V = –15 V, T = 25°C, unless otherwise noted.)CC ..
MC3458U ,V(cc): 36V; dual differential input operational amplifierELECTRICAL CHARACTERISTICS (For MC3558, MC3458, VCC = +15 V, VEE = -1 5 V, TA = 25°C, unless otherw ..
MC10H145L-MC10H145P
16 x 4 Bit Register File(RAM)
SEMICONDUCTOR TECHNICAL DATA -
The MC10H145 is a 16 x 4 bit register file. The active-low chip select allows
easy expansion.
The operating mode of the register file is controlled by the WE input. When
WE is “low” the device is in the write mode, the outputs are “low” and the data
present at Dn input is stored at the selected address, when WE is “high,” the
device is in the read mode — the data state at the selected location is present
at the Qn outputs. Address Access Time, 4.5 ns Typical Power Dissipation, 700 mW Typical Improved Noise Margin 150 mV (Over Operating Voltage and
Temperature Range) Voltage Compensated MECL 10K-Compatible
MAXIMUM RATINGS
ELECTRICAL CHARACTERISTICS (VEE = –5.2 V ±5%) (See Note)
NOTE:Each MECL 10H series circuit has been designed to meet the dc specifications shown in the test table,
after thermal equilibrium has been established. The circuit is in a test socket or mounted on a printed
circuit board and transverse air flow greater than 500 Ifpm is maintained. Outputs are terminated through
a 50-ohm resistor to –2.0 volts.
DIP
PIN ASSIGNMENTVEE
VCC
TRUTH TABLEQ-State of Addressed Cell
Pin assignment is for Dual–in–Line Package.
For PLCC pin assignment, see the Pin Conversion
Tables on page 6–11 of the Motorola MECL Data
Book (DL122/D).
