MC10H115FN ,Quad Line ReceiverMAXIMUM RATINGS736Characteristic Symbol Rating Unit1014Power Supply (V = 0) V –8.0 to 0 VdcCC EE11V ..
MC10H115FNR2 ,Quad Line Receiver
MC10H115FNR2 ,Quad Line Receiver2AND8090/DTest Bench Equipmentmust be wide enough for accurate rise and fall timeAC characterizatio ..
MC10H115L ,Quad Line ReceiverMAXIMUM RATINGS736Characteristic Symbol Rating Unit1014Power Supply (V = 0) V –8.0 to 0 VdcCC EE11V ..
MC10H115M ,Quad Line Receiver3AN1672/DSection 2: Translation from Different ECL Operating Mode Drivers to Non ECL ReceiversThe f ..
MC10H115MEL ,Quad Line Receiver3AN1672/DSection 2: Translation from Different ECL Operating Mode Drivers to Non ECL ReceiversThe f ..
MC34119P ,LOW POWER AUDIO AMPLIFIEROrder this document by MC34119/D* ** ** The MC34119 is a low power audio amplifier intergrated circ ..
MC34129D ,HIGH PERFORMANCE CURRENT MODE CONTROLLERSMAXIMUM RATINGSRating Symbol Value UnitV Zener Current I 50 mACC Z(VCC)Start/Run Output Zener Curre ..
MC34129P ,HIGH PERFORMANCE CURRENT MODE CONTROLLERSfeatures consisting of soft–start,P SUFFIXundervoltage lockout, cycle–by–cycle current limiting, ad ..
MC3414 , N-Channel 20-V (D-S) MOSFET Fast switching speed
MC34151 ,High Speed Dual MOSFET DriversELECTRICAL CHARACTERISTICS (V = 12 V, for typical values T = 25°C, for min/max values T is the onl ..
MC34151 ,High Speed Dual MOSFET Drivers3t , DRIVE OUTPUT PROPAGATION DELAY (ns)PLH(IN/OUT) I , INPUT CURRENT (mA)in100k 100kt , DRIVE OUTP ..
MC10H115FN-MC10H115L-MC10H115P
Quad Line Receiver
SEMICONDUCTOR TECHNICAL DATA -
The MC10H115 is a quad differential amplifier designed for use in sensing
differential signals over long lines. This 10H part is a functional/ pinout
duplication of the standard MECL 10K family part, with 100% improvement in
counting frequency and no increase in power–supply current.
The base bias supply (VBB) is made available at Pin 9 to make the device
useful as a Schmitt trigger, or in other applications where a stable reference
voltage is necessary. Active current sources provide the MC10H115 with
excellent common mode rejection. If any amplifier in a package is not used, one
input of that amplifier must be connected to VBB (Pin 9) to prevent upsetting the
current source bias network. Propagation Delay, 1.0 ns Typical Power Dissipation 110 mW Typ/Pkg (No Load) Improved Noise Margin 150 mV (Over Operating Voltage and
Temperature Range) Voltage Compensated MECL 10K–Compatible
MAXIMUM RATINGS
ELECTRICAL CHARACTERISTICS (VEE = –5.2 V ±5%) (2)
AC PARAMETERS
NOTES:1. When VBB is used as the reference voltage.
2. Each MECL 10H series circuit has been designed to meet the specifications shown in the test table, after thermal
equilibrium has been established. The circuit is in a test socket or mounted on a printed circuit board and transverse
air flow greater than 500 linear fpm is maintained. Outputs are terminated through a 50–ohm resistor to –2.0 volts.
3. Differential input not to exceed 1.0 Vdc.
4. 150 mVp–p differential input required to obtain full logic swing on output.
DIP
PIN ASSIGNMENTVCC1
AOUT
BOUT
AIN
AIN
BIN
BIN
VEE
VCC2
DOUT
COUT
DIN
DIN
CIN
CIN
VBB
Pin assignment is for Dual–in–Line Package.
For PLCC pin assignment, see the Pin Conversion
