IC Phoenix
 
Home ›  MM49 > MAX4028EUE-MAX4028EWE,Triple/Quad / 2:1 Video Multiplexer-Amplifiers with Input Clamps
MAX4028EUE-MAX4028EWE Fast Delivery,Good Price
Part Number:
If you need More Quantity or Better Price,Welcom Any inquiry.
We available via phone +865332716050 Email
Partno Mfg Dc Qty AvailableDescript
MAX4028EUEMAXIMN/a10avaiTriple/Quad / 2:1 Video Multiplexer-Amplifiers with Input Clamps
MAX4028EWEMAXIMN/a10avaiTriple/Quad / 2:1 Video Multiplexer-Amplifiers with Input Clamps


MAX4028EUE ,Triple/Quad / 2:1 Video Multiplexer-Amplifiers with Input ClampsApplicationsIn-Car Navigation/EntertainmentA/B+5VBlade ServersCINVCC75Ω CABLE 0.1µ FSecurity System ..
MAX4028EWE ,Triple/Quad / 2:1 Video Multiplexer-Amplifiers with Input ClampsELECTRICAL CHARACTERISTICS(V = +5V, GND = 0V, R = 150Ω to GND, V = +5V, R = 6kΩ , C = 0.1µF to GND, ..
MAX4032EUT+T ,5V, 6dB Video Buffer with Sync-Tip Clamp, Output Sag Correction, and 150nA Shutdown CurrentELECTRICAL CHARACTERISTICS(V = 5.0V, GND = 0V, C = 0.1µF from IN to GND, R = infinity to GND, SAG s ..
MAX4032EXT+T ,5V, 6dB Video Buffer with Sync-Tip Clamp, Output Sag Correction, and 150nA Shutdown CurrentBlock DiagramVideo-Enabled Cell PhonesNotebook ComputersPortable/Flat-Panel DisplaysTOP VIEW VCCMAX ..
MAX4037EUT ,Low IBIAS, +1.4V/800nA, Rail-to-Rail Op Amps with +1.2V Buffered ReferenceApplicationsPIN- TOPBattery-Powered/Solar-Powered SystemsPART TEMP RANGEPACKAGE MARKPortable Medica ..
MAX4039EUB ,Low IBIAS / +1.4V/800nA / Rail-to-Rail Op Amps with +1.2V Buffered ReferenceApplications PACKAGE MARKMAX4036EXK-T -40°C to +85°C 5 SC70-5 AFRBattery-Powered/Solar-Powered Syst ..
MAX753ESE ,CCFL Backlight and LCD Contrast ControllersFeaturesThe MAX753/MAX754 drive cold-cathode fluorescent' Drives Backplane and Backlightlamps (CCFL ..
MAX7545AKCWP ,CMOS 12-BIT BUFFERED MULTIPLYING DACsApplications Motion Control Systems Automatic Test Equipment pp Controlled Systems Progra ..
MAX7545ALP ,CMOS 12-BIT BUFFERED MULTIPLYING DACsfeatures a 100ns max write pulse width (150ns for MAX7645) which allows inter- facing to a wide r ..
MAX754CPE ,CCFL Backlight and LCD Contrast ControllersMAX753/MAX75419-0197; Rev 1; 1/95CCFL Backlight andLCD Contrast Controllers_______________
MAX754CSE ,CCFL Backlight and LCD Contrast ControllersBlock Diagram located at end of data sheet.____ Maxim Integrated Products 1 for or literature.CCF ..
MAX754ESE ,CCFL Backlight and LCD Contrast ControllersGeneral Description ________


MAX4028EUE-MAX4028EWE
Triple/Quad / 2:1 Video Multiplexer-Amplifiers with Input Clamps
General Description
The MAX4028/MAX4029 are 5V, triple/quad, 2:1 voltage-
feedback multiplexer-amplifiers with input clamps and a
fixed gain of +2V/V (6dB). Channel 1 (IN1A and IN1B)
inputs are clamped to the video sync tip of the input sig-
nal, while the remaining inputs can be clamped to either
the video sync tip or the video sync of channel 1 (IN1_).
The latter is referred to as a key clamp and is pin selec-
table. Selectable clamp/key-clamp inputs and fixed-gain
video output buffers make the MAX4028/MAX4029 ideal
for video-source switching applications such as automo-
tive entertainment systems, video projectors, and dis-
plays/TVs. Both devices have 20ns channel switching
times and low ±10mVP-Pswitching transients, making
them ideal for high-speed video switching applications
such as on-screen display (OSD) insertion.
The MAX4028/MAX4029 have a -3dB large-signal (2VP-P)
bandwidth of 130MHz, a -3dB small-signal bandwidth of
210MHz, and a 300V/µs slew rate. Low differential gain
and phase errors of 0.2% and 0.4°, respectively, make
these devices ideal for broadcast video applications.
The MAX4028/MAX4029 are specified over the -40°C to
+85°C extended temperature range and are offered in
16-pin and 20-pin TSSOP/SO packages.
Applications

In-Car Navigation/Entertainment
Blade Servers
Security Systems
Video Projectors
Displays and Digital Televisions
Broadcast and Graphics Video
Set-Top Boxes
Notebook Computers
Video Crosspoint Switching
Features
Single +5V OperationIndependently Selectable Sync-Tip or
Key-Clamp Inputs
Adjustable Key-Clamp Voltage130MHz Large-Signal -3dB Bandwidth210MHz Small-Signal -3dB Bandwidth300V/µs Slew Rate20ns Switching TimeUltra-Low ±10mVP-PSwitching Transient0.2% Differential Gain/0.4°Phase ErrorLow-Power, High-Impedance Disable Mode
MAX4028/MAX4029riple/Quad, 2:1 Video
Multiplexer-Amplifiers with Input Clamps
Ordering Information
Typical Operating Circuit

19-3240; Rev 0; 3/04
Pin Configurations appear at end of data sheet.
Selector Guide
MAX4028/MAX4029riple/Quad, 2:1 Video
Multiplexer-Amplifiers with Input Clamps
ABSOLUTE MAXIMUM RATINGS
DC ELECTRICAL CHARACTERISTICS

(VCC= +5V, GND = 0V, RL= 150Ωto GND, VDISABLE= +5V, RKEYREF= 6kΩ, CIN= 0.1µF to GND, TA= TMINto TMAX, unless otherwise
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
Supply Voltage (VCCto GND)..................................-0.3V to +6V
IN_A, IN_B, OUT_.......................................-0.3V to (VCC+ 0.3V)
DISABLE, A/B, KEYREF, CLAMP/KEY_......-0.3V to (VCC+ 0.3V)
Current Into IN_A, IN_B...................................................±0.5mA
Short-Circuit Duration (VOUTto GND)........................Continuous
Short-Circuit Duration (VOUTto VCC) .............................(Note 1)
Continuous Power Dissipation (TA= +70°C)
16-Pin TSSOP (derate 9.4mW/°C above +70°C).........755mW
16-Pin Wide SO (derate 9.5mW/°C above +70°C)......762mW
20-Pin TSSOP (derate 11mW/°C above +70°C)..........879mW
20-Pin Wide SO (derate 10mW/°C above +70°C).......800mW
Operating Temperature Range...........................-40°C to +85°C
Junction Temperature......................................................+150°C
Storage Temperature Range.............................-65°C to +150°C
Lead Temperature (soldering, 10s).................................+300°C
Note 1:
Do not short VOUTto VCC.
MAX4028/MAX4029riple/Quad, 2:1 Video
Multiplexer-Amplifiers with Input Clamps
AC ELECTRICAL CHARACTERISTICS

(VCC= +5V, GND = 0V, RL= 150Ωto GND, VDISABLE= +5V, RKEYREF= 6kΩ, CIN= 0.1µF, TA= TMINto TMAX, unless otherwise noted.
Typical values are at TA= +25°C.)
Note 3:
The clamp voltage at the input is VCLAMP(measured at the output) divided by gain + VBE.
Note 4:
The key-clamp voltage is above the sync-tip clamp voltage by approximately 0.7V, and is adjusted by varying RKEYREF.
Note 5:
Measured at f = 100Hz at thermal equilibrium.
MAX4028/MAX4029riple/Quad, 2:1 Video
Multiplexer-Amplifiers with Input Clamps
Typical Operating Characteristics

(VCC= +5V, GND = 0V, VDISABLE= +5V, RL= 150Ωto GND, CIN= 0.1µF, RKEYREF= 6.04kΩ±1%, TA= +25°C, unless otherwise
noted.)
MAX4028/MAX4029riple/Quad, 2:1 Video
Multiplexer-Amplifiers with Input Clamps
OUTPUT IMPEDANCE
vs. FREQUENCY

MAX4028 toc10
FREQUENCY (Hz)
OUTPUT IMPEDANCE (
100M10M1M100k
10k1G
INPUT-VOLTAGE NOISE DENSITY
vs. FREQUENCY

MAX4028 toc11
FREQUENCY (Hz)
INPUT-VOLTAGE NOISE DENSITY (nV/
100k10k1k10010
11M
LARGE-SIGNAL TRANSIENT RESPONSE

MAX4028 toc12
10ns/div
1.6VDCVIN
500mV/div
VOUT
1V/div
SMALL-SIGNAL TRANSIENT RESPONSE

MAX4028 toc13
10ns/div
1.6VDCVIN
25mV/div
SIGNAL 2
50mV/div
CHANNEL-SWITCHING TRANSIENT

MAX4028 toc14
20ns/div
5VDC
0VDC
A/B
2.5V/div
VOUT
20mV/div
CHANNEL-SWITCHING TIME
(CHA = 1.5VDC, CHB = 1VDC)

MAX4028 toc15
20ns/div
5VDC
0VDC
A/B
2.5V/div
VOUT
500mV/div
ENABLE RESPONSE TIME
(VOUT = 0.5V)

MAX4028 toc16
50ns/div
5VDC
0VDC
0.5VDC
0VDC
ENABLE
2.5V/div
VOUT
250mV/div
SMALL-SIGNAL BANDWIDTH
vs. FREQUENCY

MAX4028 toc17
FREQUENCY (Hz)
SMALL-SIGNAL BANDWIDTH (dB)
100M10M1M
100k1G
OPTIMAL ISOLATION RESISTANCE
vs. CAPACITIVE LOAD

MAX4028 toc18
CLOAD (pF)
OPTIMAL ISOLATION RESISTANCE (
0250ypical Operating Characteristics (continued)
(VCC= +5V, GND = 0V, VDISABLE= +5V, RL= 150Ωto GND, CIN= 0.1µF, RKEYREF= 6.04kΩ±1%, TA= +25°C, unless otherwise
noted.)
MAX4028/MAX4029riple/Quad, 2:1 Video
Multiplexer-Amplifiers with Input Clamps
Typical Operating Characteristics (continued)

(VCC= +5V, GND = 0V, VDISABLE= +5V, RL= 150Ωto GND, CIN= 0.1µF, RKEYREF= 6.04kΩ±1%, TA= +25°C, unless otherwise
noted.)
Detailed Description
The MAX4028/MAX4029 are 5V, triple/quad, 2:1 voltage-
feedback multiplexer-amplifiers with input clamps and a
fixed gain of +2V/V (6dB). Channel 1 (IN1A and IN1B)
inputs are clamped to the video sync tip of the input
IN1_ channel, while the remaining inputs can be
clamped to either the video sync tip of the respective
input channel (IN_A and IN_B) or the video sync of
channel 1 (IN1_). The latter is referred to as a key
clamp and is pin selectable. Selectable clamp/key-
clamp inputs and fixed-gain video output buffers make
the MAX4028/MAX4029 ideal for video-source switching
applications such as automotive entertainment systems,
video projectors, and displays/TVs. Both devices have
20ns channel switching times and low ±10mVP-Pswitch-
ing transients, making them ideal for both high-speed
video switching applications such as OSD insertion.
The MAX4028/MAX4029 have a -3dB large-signal (2VP-P)
bandwidth of 130MHz, a -3dB small-signal bandwidth of
210MHz, and a 300V/µs slew rate. Low differential gain
and phase errors of 0.2% and 0.4°, respectively, make
these devices ideal for broadcast video applications.
Sync Tip and Key Clamps

The MAX4028/MAX4029 have AC-coupled inputs, with
either a sync tip or key clamp to provide bias for the
video signal. Channel 1 of the MAX4028/MAX4029
always has a sync tip clamp at the input, while the
remaining channels are selectable as either sync tip or
key clamps to accommodate the various video wave-
forms (see the Clamp/Key-Clamp Settings for Video
Formatssection). The value of the sync-tip clamp voltage
is set internally for the lowest value, consistent with linear
operation, and cannot be adjusted. The key-clamp volt-
age is adjustable, to compensate for variations in the
voltage between component video inputs such as Linear
RGB, YPbPr, and Y-C, by varying RKEYREF. The key-
clamp voltage can be computed from:
VKey-Clamp = 0.40 + 2000/[(5000 x RKEYREF) /
(5000 + RKEYREF)]
MAX4028/MAX4029riple/Quad, 2:1 Video
Multiplexer-Amplifiers with Input Clamps
Pin Description (continued)
ic,good price


TEL:86-533-2716050      FAX:86-533-2716790
   

©2020 IC PHOENIX CO.,LIMITED