MAX3208EAUB+ ,Dual, Quad, and Hex High-Speed Differential ESD-Protection ICsMAX3205E/MAX3207E/MAX3208E19-3361; Rev 3; 7/10Dual, Quad, and Hex High-SpeedDifferential ESD-Protec ..
MAX3208EAUB+T ,Dual, Quad, and Hex High-Speed Differential ESD-Protection ICsFeatures♦ Low Input Capacitance of 2pF TypicalThe MAX3205E/MAX3207E/MAX3208E low-capaci-tance, ±15k ..
MAX3209E ,±15kV ESD-Protected, 12V, Dual RS-232 Serial Port with Low-Power Standby for Motherboards/DesktopsApplicationsDesktop PCsTOP VIEWMotherboardsInstruments40 39 38 37 36 35 3433 32 31Equipment Requiri ..
MAX3209ECUU ,【15kV ESD-Protected, 12V, Dual RS-232 Serial Port with Low-Power Standby for Motherboards/Desktopsfeatures a 50μA low-power standby♦ 460kbps Data Rate; LapLink Compatiblemode for compliance with sy ..
MAX3209ECUU ,【15kV ESD-Protected, 12V, Dual RS-232 Serial Port with Low-Power Standby for Motherboards/DesktopsELECTRICAL CHARACTERISTICS(V = +10.8V to +13.2V, V = +3V to +5.5V, C1 = C2 = 0.1μF, T = T to T , un ..
MAX3209ECUU+ ,±15kV ESD-Protected, 12V, Dual RS-232 Serial Port with Low-Power Standby for Motherboards/DesktopsFeaturesThe MAX3209E is a complete, dual DTE RS-232 serial♦ Two Complete Serial Ports in a Single 3 ..
MAX6428MRUR+T ,Low-Power, Single/Dual-Level Battery Monitors with Hysteresis
MAX642ACPA ,+12V fixed output, 10W CMOS step-up switching regulator. 5% output accuracy
MAX642ACPA ,+12V fixed output, 10W CMOS step-up switching regulator. 5% output accuracy
MAX642ACPA ,+12V fixed output, 10W CMOS step-up switching regulator. 5% output accuracy
MAX642ACSA ,+12V fixed output, 10W CMOS step-up switching regulator. 5% output accuracy
MAX6433UK ,Low-Power, Single/Dual-Level Battery Monitors with Hysteresis
MAX3205EATE+T-MAX3207EAUT+-MAX3207EAUT+T-MAX3208EAUB+-MAX3208EAUB+T
Dual, Quad, and Hex High-Speed Differential ESD-Protection ICs
General DescriptionThe MAX3205E/MAX3207E/MAX3208E low-capaci-
tance, ±15kV ESD-protection diode arrays with an inte-
grated transient voltage suppressor (TVS) clamp are
suitable for high-speed and general-signal ESD protec-
tion. Low input capacitance makes these devices ideal
for ESD protection of signals in HDTV, PC monitors
(DVI™, HDMI®), PC peripherals (FireWire®, USB 2.0),
server interconnect (PCI Express®, InfiniBand™),
datacom, and interchassis interconnect. Each channel
consists of a pair of diodes that steer ESD current puls-
es to VCCor GND.
The MAX3205E/MAX3207E/MAX3208E protect against
ESD pulses up to ±15kV Human Body Model, ±8kV
Contact Discharge, and ±15kV Air-Gap Discharge, as
specified in IEC 61000-4-2. An integrated TVS ensures
that the voltage rise seen on VCCduring an ESD event
is clamped to a known voltage. These devices have a
2pF input capacitance per channel, and a channel-to-
channel capacitance variation of only 0.05pF, making
them ideal for use on high-speed, single-ended, or dif-
ferential signals.
The MAX3207E is a two-channel device suitable for
USB 1.1, USB 2.0 (480Mbps), and USB OTG applica-
tions. The MAX3208E is a four-channel device for
Ethernet and FireWire applications. The MAX3205E is a
six-channel device for cell phone connectors and
SVGA video connections.
The MAX3205E is available in 9-bump, tiny wafer-level
package (WLP) and 16-pin, 3mm x 3mm, thin QFN
packages. The MAX3207E is available in a small 6-pin
SOT23 package. The MAX3208E is available in 10-pin
µMAX®and 16-pin, 3mm x 3mm TQFN packages. All
devices are specified for the -40°C to +125°C automo-
tive operating temperature range.
ApplicationsDVI Input/Output Protection
Set-Top Boxes
PDAs/Cell Phones
Graphics Controller Cards
Displays/Projectors
High-Speed, Full-Speed and Low-Speed USB
Port Protection
FireWire IEEE 1394 Ports
Consumer Equipment
High-Speed Differential Signal Protection
FeaturesLow Input Capacitance of 2pF TypicalLow Channel-to-Channel Variation of 0.05pF
from I/O to I/OHigh-Speed Differential or Single-Ended ESD
Protection
±15kV–Human Body Model
±8kV–IEC 61000-4-2, Contact Discharge
±15kV–IEC 61000-4-2, Air-Gap DischargeIntegrated Transient Voltage Suppressor (TVS)Optimized Pinout for Minimized Stub Inductance
on Controlled-Impedance Differential-
Transmission Line Routing-40°C to +125°C Automotive Operating
Temperature RangeWLP Packaging Available
MAX3205E/MAX3207E/MAX3208E
Dual, Quad, and Hex High-Speed
Differential ESD-Protection ICs
Ordering Information19-3361; Rev 3; 7/10
FireWire is a registered trademark of Apple Inc.
PCI Express is a registered service mark of PCI-SIG Corporation.
DVI is a trademark of Digital Display Working Group.
HDMIis a registered trademark and registered service mark of
HDMILicensing, LCC.
InfiniBand is a trademark and service mark of InfiniBand Trade
Association.
µMAX is a registered trademark of Maxim Integrated Products, Inc.
Typical Operating Circuit and Pin Configurations appear at
PARTTEMP RANGEPIN-PACKAGE
MAX3205EAWL+T-40°C to +125°C 9 WLP
MAX3205EATE+-40°C to +125°C 16 TQFN-EP*
MAX3207EAUT+T-40°C to +125°C 6 SOT23
MAX3208EAUB+ -40°C to +125°C 10 μMAX
MAX3208EATE+ -40°C to +125°C 16 TQFN-EP*
Selector Guide
PARTESD-PROTECTED
I/O PORTSTOP MARK MAX3205EAWL+T 6 AIN
MAX3205EATE+ 6 ACO
MAX3207EAUT+T 2 ABVG
MAX3208EAUB+ 4 —
MAX3208EATE+ 4 ACN
+Denotes a lead(Pb)-free/RoHS-compliant package.
T = Tape and reel.
*EP = Exposed pad.
MAX3205E/MAX3207E/MAX3208E
Dual, Quad, and Hex High-Speed
Differential ESD-Protection ICs
ABSOLUTE MAXIMUM RATINGS
ELECTRICAL CHARACTERISTICS(VCC= +5V, TA= TMINto TMAX, unless otherwise noted. Typical values are at VCC= +5V and TA= +25°C.) (Note 1)
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
Note 1:Parameters are 100% production tested at +25°C. Limits over temperature are guaranteed by design only.
Note 2:Idealized clamp voltages. See the Applications Informationsection for more information.
Note 3:Guaranteed by design, not production tested.
VCCto GND...........................................................-0.3V to +6.0V
I/O_ to GND................................................-0.3V to (VCC+ 0.3V)
Continuous Power Dissipation (TA= +70°C)
6-Pin SOT23 (derate 8.7mW/°C above +70°C)............696mW
9-Bump WLP (derate 14.1mW/°C above +70°C).............0mW
10-Pin µMAX (derate 5.6mW/°C above +70°C)...........444mW
16-Pin TQFN (derate 20.8mW/°C above +70°C).......1667mW
Operating Temperature Range.........................-40°C to +125°C
Storage Temperature Range.............................-65°C to +150°C
Junction Temperature .....................................................+150°C
Lead Temperature (excluding WLP; soldering, 10s).......+300°C
Soldering Temperature (reflow).......................................+260°C
PARAMETERSYMBOLCONDITIONSMINTYPMAXUNITS Supply Voltage VCC 0.9 5.5 V
Supply Current ICC 1 100 nA
Diode Forward Voltage VFIF = 10mA 0.65 0.95 V
Positive transients VCC + 25 TA = +25°C, ±15kV Human
Body Model, IF= 10A Negative transients -25
Positive transients VCC + 60 TA = +25°C, ±8kV Contact
Discharge (IEC 61000-4-2),
IF = 24A Negative transients -60
Positive transients VCC + 100
Channel Clamp Voltage
(Note 2) VC
TA = +25°C, ±15kV Air-Gap
Discharge (IEC 61000-4-2),
IF = 45A Negative transients -100
Channel Leakage Current -0.1 +0.1 μA
MAX3205EAWL+T
MAX3207EAUT+T 2.5 3
MAX3205EATE+
MAX3208EATE+ 2.7 3.2 Channel I/O Capacitance VCC = +3.3V, bias of VCC / 2
MAX3208EAUB+ 2.6 3.1
pF
Channel I/O to I/O
Variation in Capacitance CIN VCC = +3.3V, bias of VCC / 2, CI/O_ to GND ±0.05 pF
TRANSIENT SUPPRESSOR VCC Capacitance to GND 10 pF
ESD Trigger Voltage dV/dt 1V/ns (Note 3) 9 V
MAX3205E/MAX3207E/MAX3208E
Dual, Quad, and Hex High-Speed
Differential ESD-Protection ICs
CLAMP VOLTAGE
vs. DC CURRENTMAX3205E toc01
DC CURRENT (mA)
CLAMP VOLTAGE (V)
I/O_ TO VCC
GND TO I/O_
LEAKAGE CURRENT
vs. TEMPERATUREMAX3205E toc02
TEMPERATURE (°C)
LEAKAGE CURRENT (pA)400
10,000
INPUT CAPACITANCE
vs. INPUT VOLTAGE
MAX3205E toc03
INPUT VOLTAGE (V)
INPUT CAPACITANCE (pF)321
Typical Operating Characteristics(VCC= +5V, TA = +25°C, unless otherwise noted.)
Pin Description
PIN
MAX3205EMAX3207EMAX3208E
TQFN-EPWLPSOT23μMAXTQFN-EP
NAMEFUNCTION 4, 5, 7,
12, 13, 15
A2, A3, B1,
B3, C1, C2 1, 4 1, 4, 6, 9 4, 7, 12, 15 I/O_ ESD-Protected Channel
1, 3, 6, 8,
9, 11, 14, 3, 6 2, 5, 7, 10
1, 3, 5, 6,
8, 9, 11,
13, 14, 16
N.C. No Connection. Not internally connected. B2 — — — N.C. No Connection. The solder sphere is omitted from
this location (see the Package Information section). A1 2 3 2 GND Ground. Connect GND with a low-impedance
connection to the ground plane.
10 C3 5 8 10 VCC
Power-Supply Input. Bypass VCC to GND with a
0.1μF ceramic capacitor as close to the device as
possible. — — — — EP Exposed Pad (TQFN Only). Connect EP to GND.
MAX3205E/MAX3207E/MAX3208E
Detailed DescriptionThe MAX3205E/MAX3207E/MAX3208E low-capacitance,
±15kV ESD-protection diode arrays with an integrated
transient voltage suppressor (TVS) clamp are suitable for
high-speed and general-signal ESD protection. Low
input capacitance makes these devices ideal for ESD
protection of signals in HDTV, PC monitors (DVI, HDMI),
PC peripherals (FireWire, USB 2.0), server interconnect
(PCI Express, InfiniBand), datacom, and interchassis
interconnect. Each channel consists of a pair of diodes
that steer ESD current pulses to VCCor GND. The
MAX3207E, MAX3208E, and MAX3205E are two, four,
and six channels (see the Functional Diagram).
The MAX3205E/MAX3207E/MAX3208E are designed to
work in conjunction with a device’s intrinsic ESD pro-
tection. The MAX3205E/MAX3207E/MAX3208E limit the
excursion of the ESD event to below ±25V peak voltage
when subjected to the Human Body Model waveform.
When subjected to the IEC 61000-4-2 waveform and
Contact Discharge, the peak voltage is limited to ±60V.
The peak voltage is limited to ±100V when subjected to
Air-Gap Discharge. The device protected by the
MAX3205E/MAX3207E/MAX3208E must be able to
withstand these peak voltages, plus any additional volt-
age generated by the parasitic of the board.
A TVS is integrated into the MAX3205E/MAX3207E/
MAX3208E to help clamp ESD to a known voltage. This
helps reduce the effects of parasitic inductance on the
VCCrail by clamping VCCto a known voltage during an
ESD event. For the lowest possible clamp voltage dur-
ing an ESD event, placing a 0.1µF capacitor as close to
VCCas possible is recommended.
Dual, Quad, and Hex High-Speed
Differential ESD-Protection ICsMAX3207E
VCC
GND
I/O1I/O2
MAX3208E
VCC
GND
I/O1I/O2I/O3I/O4
MAX3205E
VCC
GND
I/O1I/O2I/O5I/O6I/O3I/O4
Functional Diagram
Applications Information
Design ConsiderationsMaximum protection against ESD damage results from
proper board layout (see the Layout Recommendations
section). A good layout reduces the parasitic series
inductance on the ground line, supply line, and protect-
ed signal lines. The MAX3205E/MAX3207E/MAX3208E
ESD diodes clamp the voltage on the protected lines
during an ESD event and shunt the current to GND or
VCC. In an ideal circuit, the clamping voltage (VC) is
defined as the forward voltage drop (VF) of the protec-
tion diode, plus any supply voltage present on the cath-
ode.
For positive ESD pulses:= VCC+ VF
For negative ESD pulses:=-VF
The effect of the parasitic series inductance on the
lines must also be considered (Figure 1).
For positive ESD pulses:
For negative ESD pulses:
where IESDis the ESD current pulse.
During an ESD event, the current pulse rises from zero
to peak value in nanoseconds (Figure 2). For example,
in a 15kV IEC 61000 Air-Gap Discharge ESD event, the
pulse current rises to approximately 45A in 1ns (di/dt =
45 x 109). An inductance of only 10nH adds an addi-
tional 450V to the clamp voltage and represents
approximately 0.5in of board trace. Regardless of the
device’s specified diode clamp voltage, a poor layout
with parasitic inductance significantly increases the
effective clamp voltage at the protected signal line.
Minimize the effects of parasitic inductance by placing
the MAX3205E/MAX3207E/MAX3208E as close to the
connector (or ESD contact point) as possible.
A low-ESR 0.1µF capacitor is recommended between
VCCand GND in order to get the maximum ESD protec-
tion possible. This bypass capacitor absorbs the
charge transferred by a positive ESD event. Ideally, the
supply rail (VCC) would absorb the charge caused by a
positive ESD strike without changing its regulated
value. All power supplies have an effective output
impedance on their positive rails. If a power supply’s
effective output impedance is 1Ω, then by using V = I x
R, the clamping voltage of VCincreases by the equa-
tion VC= IESDx ROUT. A +8kV IEC 61000-4-2 ESD
event generates a current spike of 24A. The clamping
voltage increases by VC= 24A x 1Ω, or VC= 24V.
Again, a poor layout without proper bypassing increas-
es the clamping voltage. A ceramic chip capacitor
mounted as close as possible to the MAX3205E/
MAX3207E/MAX3208E VCCpin is the best choice for
this application. A bypass capacitor should also be
placed as close to the protected device as possible.LxdILxdICFDESDESD () ()=−+⎛⎜⎞⎟+⎛⎜⎞⎟⎛⎜⎞⎟()213VLxdILxdICCCFDESDESD () () =++⎛⎜⎞⎟+⎛⎜⎞⎟()112
MAX3205E/MAX3207E/MAX3208E
Dual, Quad, and Hex High-Speed
Differential ESD-Protection ICsPROTECTED
LINE
GROUND RAIL
POSITIVE SUPPLY RAIL
I/O_
Figure 1. Parasitic Series Inductance
tR = 0.7ns to 1ns30ns
60ns
100%
90%
10%
PEAK
Figure 2. IEC 61000-4-2 ESD Generator Current Waveform
MAX3205E/MAX3207E/MAX3208E
±15kV ESD ProtectionESD protection can be tested in various ways. The
MAX3205E/MAX3207E/MAX3208E are characterized
for protection to the following limits:±15kV using the Human Body Model±8kV using the Contact Discharge Method specified
in IEC 61000-4-2±15kV using the IEC 61000-4-2 Air-Gap Discharge
Method
ESD Test ConditionsESD performance depends on a number of conditions.
Contact Maxim for a reliability report that documents
test setup, methodology, and results.
Human Body ModelFigure 3 shows the Human Body Model, and Figure 4
shows the current waveform it generates when dis-
charged into a low impedance. This model consists of
a 100pF capacitor charged to the ESD voltage of inter-
est, which is then discharged into the device through a
1.5kΩresistor.
IEC 61000-4-2The IEC 61000-4-2 standard covers ESD testing and
performance of finished equipment. The MAX3205E/
MAX3207E/MAX3208E help users design equipment
that meets Level 4 of IEC 61000-4-2. The main differ-
ence between tests done using the Human Body Model
and IEC 61000-4-2 is higher peak current in IEC 61000-
4-2. Because series resistance is lower in the IEC
61000-4-2 ESD test model (Figure 5), the ESD-
withstand voltage measured to this standard is general-
ly lower than that measured using the Human Body
Model. Figure 2 shows the current waveform for the
±8kV, IEC 61000-4-2 Level 4, ESD Contact Discharge
test. The Air-Gap Discharge test involves approaching
the device with a charged probe. The Contact
Discharge method connects the probe to the device
before the probe is energized.
Dual, Quad, and Hex High-Speed
Differential ESD-Protection ICsCHARGE-CURRENT-
LIMIT RESISTOR
DISCHARGE
RESISTANCE
STORAGE
CAPACITOR
100pF
1MΩ
RD
1.5kΩ
HIGH-
VOLTAGE
SOURCE
DEVICE
UNDER
TEST
Figure 3. Human Body ESD Test Model
IP 100%
90%
36.8%
tRLTIME
tDL
CURRENT WAVEFORM
PEAK-TO-PEAK RINGING
(NOT DRAWN TO SCALE)
10%
AMPERES
Figure 4. Human Body Model Current Waveform
CHARGE-CURRENT-
LIMIT RESISTOR
DISCHARGE
RESISTANCE
STORAGE
CAPACITOR
150pF
50MΩ TO 100MΩ
RD
330Ω
HIGH-
VOLTAGE
SOURCE
DEVICE
UNDER
TEST
Figure 5. IEC 61000-4-2 ESD Test Model
