MAX2209EBS+T ,RF Power DetectorApplications Ordering InformationDual-Band WCDMA HandsetsPIN- TOP PART TEMP RANGEH ..
MAX220CPE ,+5V-Powered, Multichannel RS-232 Drivers/ReceiversELECTRICAL CHARACTERISTICS—MAX220/222/232A/233A/242/243(V = +5V ±10%, C1–C4 = 0.1µF‚ MAX220, C1 = 0 ..
MAX220CPE+ ,+5V-Powered, Multichannel RS-232 Drivers/ReceiversFeaturesThe MAX220–MAX249 family of line drivers/receivers isSaves Board Spaceintended for all EIA/ ..
MAX220CSE ,+5V-Powered, Multichannel RS-232 Drivers/ReceiversApplicationsPART TEMP. RANGE PIN-PACKAGEPortable ComputersMAX220CPE 0°C to +70°C 16 Plastic DIPLow- ..
MAX220CSE ,+5V-Powered, Multichannel RS-232 Drivers/ReceiversMAX220–MAX24919-4323; Rev 9; 4/00+5V-Powered, Multichannel RS-232Drivers/Receivers
MAX220CSE+ ,+5V-Powered, Multichannel RS-232 Drivers/ReceiversApplications• Interface Translation• Multidrop RS-232 Networks• Portable Diagnostics EquipmentAutoS ..
MAX529CWG ,Octal, 8-Bit, Serial DACs with Output BufferELECTRICAL CHARACTERISTICS - MAX528
(Unbuffered Mode: VDD = +12V, Vss = OV; Full-Buffered Mode: ..
MAX529CWG ,Octal, 8-Bit, Serial DACs with Output BufferELECTRICAL CHARACTERISTICS - MAX528
(Unbuffered Mode: VDD = +12V, Vss = OV; Full-Buffered Mode: ..
MAX529CWG+ ,Octal, Serial, 8-Bit DAC with Output BuffersELECTRICAL CHARACTERISTICS - MAX528
(Unbuffered Mode: VDD = +12V, Vss = OV; Full-Buffered Mode: ..
MAX529EPP ,Octal, 8-Bit, Serial DACs with Output BufferGeneral Description
The MAX528/MAX529 are monolithic devices combining
an octal 8-bit, digital- ..
MAX529EWG ,Octal, 8-Bit, Serial DACs with Output BufferApplications
Digital Gain and Offset Adjustment
Digital Calibration
Multiple Trim Pot Replac ..
MAX529EWG+T ,Octal, Serial, 8-Bit DAC with Output BuffersGeneral Description
The MAX528/MAX529 are monolithic devices combining
an octal 8-bit, digital- ..
MAX2209EBS+-MAX2209EBS+T
RF Power Detector
RF Power Detector
MAX2209
19-4946; Rev 0; 10/09
Ordering Information
Pin Configuration/Functional Diagram/Typical Operating Circuit
General Description
The MAX2209 is a wideband (800MHz to 2GHz) RF
power detector. It takes an RF signal from the directional
coupler at the input, and outputs a DC voltage propor-
tional to the RF peak voltage. The change in output
voltage versus temperature is very repeatable from part
to part and enables a lookup table based on nominal
behavior, minimizing the effective detection error to less
than Q0.5dB relative to room temperature.
The MAX2209 comes in a space-saving 2 x 2, 0.5mm
pitch wafer-level package (WLP) and requires only two
external components.
Applications
Dual-Band WCDMA Handsets
High-Speed Downlink Packet Access (HSDPA)
High-Speed Uplink Packet Access (HSUPA)
Features-25dBm to 0dBm Power Detection Range±0.5dB Detection Error Due to Temperature+2.7V to +5V Single-Supply OperationSpace-Saving 4-Bump, 1mm2 UCSP™ PackageOn-Chip 50I Termination and DC-Blocking
Capacitor
+Denotes a lead(Pb)-free/RoHS-compliant package.
UCSP is a trademark of Maxim Integrated Products, Inc.
EVALUATION KITAVAILABLE
PARTTEMP RANGEPIN-
PACKAGE
TOP
MARK
MAX2209EBS+-40NC to +85NC4 UCSPAGJ
RF INPUT
ADC
VCC
OUT
VCC
GND
RFIN
MAX2209
RF Power Detector
MAX2209
AC ELECTRICAL CHARACTERISTICS
(TA = -40NC to +85NC, 50I system, VCC = 2.8V. Typical values are at TA = +25NC, unless otherwise noted.) (Note 3)
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect device reliability.
VCC to GND .............................................................-0.3V to +6V
RFIN to GND .........................................-0.3V to + (VCC + 0.3V)
OUT to GND ..........................................-0.3V to + (VCC + 0.3V)
RFIN Input Power ..........................................................+10dBm
Continuous Power Dissipation (TA = +70NC)
4-Bump WLP (derate 3mW/NC above +70NC) .............238mW
Junction-to-Ambient Thermal
Resistance (BJA) (Note 1) ..........................................335NC/W
Operating Temperature Range ..........................-40NC to +85NC
Storage Temperature Range ............................-65NC to +160NC
Junction Temperature ....................................................+150NC
Bump Temperature (soldering, Note 2)Infrared (15s) ...............................................................+260NC
DC ELECTRICAL CHARACTERISTICS
(VCC = 2.7V to 5.0V, TA = -40NC to +85NC, no RF signal applied. Typical values are at VCC = 2.8V, TA = +25NC, unless otherwise
noted.) (Note 3)
ABSOLUTE MAXIMUM RATINGS
Note 1: Package thermal resistances were obtained using the method described in JEDEC specification JESD51-7, using a
4-layer board. For detailed information on package thermal considerations, refer to /thermal-tutorial.
Note 2: For detailed information on soldering, refer to Application Note 1891: Wafer-Level Packaging (WLP) and Its Applications.
CAUTION! ESD SENSITIVE DEVICENote 3: Guaranteed by production test at TA = +25NC. Guaranteed by design and characterization at TA = -40NC and
TA = +85NC.
Note 4: Guaranteed by design and characterization. See the Typical Operating Characteristics.
PARAMETERCONDITIONSMINTYPMAXUNITS
Supply Voltage2.75.0V
Supply Current3.66mA
Idle Output VoltageVCC = 2.8V, no RF signal35mV
Output Current Source CapabilityPIN = 0dBm, VOUT forced to 0.5V7501800FA
Output Current Sink CapabilityNo RF signal, VOUT forced to 2V300525FA
PARAMETERCONDITIONSMINTYPMAXUNITS
RF Input Frequency8002000MHz
RF Input VSWR800MHz-17dB2000MHz-12
Output Voltage, 836MHz-5dBm input0.88V-25dBm input0.06
Output Voltage, 1950MHz-5dBm input0.72V-25dBm input0.06
Residual Error after Room
Temperature Calibration
(TA = -40NC to +85NC) (Note 4)
-5dBm inputQ0.5
-25dBm inputQ1.5
MAX2209
RF Power Detector
Typical Operating Characteristics
(VCC = 2.8V, typical values are at TA = +25NC, unless otherwise noted.)
INPUT POWER (dBm)
OUT (V)-10-15-20
OUTPUT VOLTAGE vs. INPUT POWER
(RF = 836MHz)
MAX2209 toc01
INPUT POWER (dBm)
OUT (V)-10-15-20
OUTPUT VOLTAGE vs. INPUT POWER
(RF = 1950MHz)
MAX2209 toc02
OUTPUT VOLTAGE vs. FREQUENCY
MAX2209 toc03
INPUT FREQUENCY (MHz)
OUT (V)
PIN = -15dBm
PIN = -10dBm
PIN = -5dBm
INPUT POWER (dBm)
ERROR (dB)-10-15-20
ERROR DUE TO TEMPERATURE
(RF = 836MHz, 58 UNITS)
MAX2209 toc04-40°C
+85°C
INPUT POWER (dBm)
ERROR (dB)-10-15-20
MAX2209 toc05
-40°C
+85°C
ERROR DUE TO TEMPERATURE
(RF = 1950MHz, 58 UNITS)SIGMA OF -40°C ERROR
INPUT POWER (dBm)
SIGMA (dB)
MAX2209 toc06-10-15-20-250
RF = 1950MHz
RF = 836MHz
SIGMA OF +85°C ERROR
SIGMA (dB)-10-15-20
MAX2209 toc07
RF = 1950MHz
RF = 836MHz
RESIDUAL ERROR AFTER ROOM
TEMPERATURE CALIBRATION
MAX2209 toc08
ERROR (dB)
RF = 836MHz, 58 UNITS, -40°C
RESIDUAL ERROR AFTER ROOM
TEMPERATURE CALIBRATION
MAX2209 toc09
ERROR (dB)
RF = 836MHz, 58 UNITS, +85°C
RF Power Detector
MAX2209
Typical Operating Characteristics (continued)
(VCC = 2.8V, typical values are at TA = +25NC, unless otherwise noted.)
RESIDUAL ERROR AFTER ROOM
TEMPERATURE CALIBRATION
MAX2209 toc10
INPUT POWER (dBm)
ERROR (dB)
RF = 1950MHz, 58 UNITS, -40°C
RESIDUAL ERROR AFTER ROOM
TEMPERATURE CALIBRATION
MAX2209 toc11
INPUT POWER (dBm)
ERROR (dB)
RF = 1950MHz, 58 UNITS, +85°C
TIME (s)
OUT (V)
5.0E-071.0E-061.5E-062.0E-06
0.0E+00
SETTLING TIME FROM RF POWER
(ON/OFF RF = 836MHz)
MAX2209 toc12
PIN = -5dBm
PIN = -7dBm
PIN = -10dBm
PIN = -15dBm
MAX2209
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied.
RF Power Detector
Package Information
For the latest package outline information and land pat-
terns, go to /packages. Note that “+”, “#”, or “-” in the package code indicates RoHS
status only. Package drawings may show a different suf-
fix character, but the drawing pertains to the package
regardless of RoHS status.
PACKAGE TYPEPACKAGE CODEDOCUMENT NO.
4 UCSPB4+421-0117
Chip Information
PROCESS: BIPOLAR
Pin Description
Detailed Description
The MAX2209 power detector is designed to oper-
ate from 800MHz to 2.0GHz. The device is ideal for
wideband code-division multiple access (WCDMA),
cdma2000M, and high-speed downlink/uplink packet
access. The MAX2209 accepts an RF signal at the input,
and outputs a temperature-independent voltage related
to the input signal voltage. The output voltage expressed
in dBV is proportional to the input power expressed in
dBm. The device has a detection range from -25dBm to
0dBm.
Applications Information
The MAX2209 contains an internal termination resistor
for use with directional couplers. The typical application
circuit is shown in Figure 1. The output of the detector
goes to an ADC for further processing by the baseband
system. Connect a series resistor and shunt capacitor to
the MAX2209 output to reduce residual amplitude ripple.
Layout
There are two areas that require attention: the GND pin
and the supply bypassing. Connect the GND pin to the
PCB ground with a GND via as close as possible, and
bypass VCC to ground with a capacitor as close as pos-
sible to the part.
Figure 1. Typical Application Circuit
cdma2000 is a registered trademark of the Telecommunications
Industry Association.
BUMPNAMEFUNCTIONOUTDetector OutputVCCPower Supply. Bypass to GND with a capacitor as close as possible to the bump.GNDGround Connection. Connect to PCB ground plane with as low inductance as possible.RFINRF Input. Internally terminated to 50I. AC-couple the RF input to this pin.
RF INPUT
ADC
VCC
MAX2209
OUT
VCC
GND
RFIN
DIRECTIONAL
COUPLER
ANTENNA
This datasheet has been :
www.ic-phoenix.com
Datasheets for electronic components.
