IC Phoenix
 
Home ›  MM36 > MAX218CAP+-MAX218EAP+,1.8V to 4.25V Powered, True RS-232 Dual Transceiver
MAX218CAP+-MAX218EAP+ Fast Delivery,Good Price
Part Number:
If you need More Quantity or Better Price,Welcom Any inquiry.
We available via phone +865332716050 Email
Partno Mfg Dc Qty AvailableDescript
MAX218CAP+MAIXMN/a1500avai1.8V to 4.25V Powered, True RS-232 Dual Transceiver
MAX218EAP+ |MAX218EAPMAXN/a10avai1.8V to 4.25V Powered, True RS-232 Dual Transceiver


MAX218CAP+ ,1.8V to 4.25V Powered, True RS-232 Dual TransceiverFeaturesThe MAX218 RS-232 transceiver is intended for battery-BETTER THAN BIPOLAR!powered EIA/TIA-2 ..
MAX218CWP ,1.8V to 4.25V-Powered, True RS-232 Dual TransceiverFeaturesThe MAX218 RS-232 transceiver is intended for battery-BETTER THAN BIPOLAR!powered EIA/TIA-2 ..
MAX218EAP ,1.8V to 4.25V-Powered, True RS-232 Dual TransceiverMAX21819-0246; Rev 1; 7/951.8V to 4.25V-Powered,True RS-232 Dual Transceiver_______________
MAX218EAP+ ,1.8V to 4.25V Powered, True RS-232 Dual TransceiverApplicationsMAX218CWP 0°C to +70°C 20 Wide SOBattery-Powered EquipmentMAX218CAP 0°C to +70°C 20 SSO ..
MAX218EWP ,1.8V to 4.25V-Powered, True RS-232 Dual TransceiverGeneral Description ________
MAX2205EBS ,RF Power Detectors in UCSPELECTRICAL CHARACTERISTICS (MAX2205–MAX2208)(V = +2.7V to +5.0V, SHDN = +2.0V, no RF signal applied ..
MAX528CWG+ ,Octal, Serial, 8-Bit DAC with Output BuffersELECTRICAL CHARACTERISTICS - MAX528 (Unbuffered Mode: VDD = +12V, Vss = OV; Full-Buffered Mode: ..
MAX528EAG ,Octal, 8-Bit, Serial DACs with Output BufferFeatures ' Now Available in Space-Saving SSOP ' 8 Buffered Noninverting Outputs ' Buffer D ..
MAX528EPP+ ,Octal, Serial, 8-Bit DAC with Output BuffersGeneral Description The MAX528/MAX529 are monolithic devices combining an octal 8-bit, digital- ..
MAX528EWG ,Octal, 8-Bit, Serial DACs with Output Buffer19-4193; Rev 2; 5/94
MAX528EWG+ ,Octal, Serial, 8-Bit DAC with Output BuffersApplications Digital Gain and Offset Adjustment Digital Calibration Multiple Trim Pot Replac ..
MAX5290AETE ,Buffered, Fast-Settling, Dual, 12-/10-/8-Bit, Voltage-Output DACsFeaturesThe MAX5290–MAX5295 dual, 12-/10-/8-bit, voltage- Dual, 12-/10-/8-Bit Serial DACs in 4mm x ..


MAX218CAP+-MAX218EAP+
1.8V to 4.25V Powered, True RS-232 Dual Transceiver
_______________General Description
The MAX218 RS-232 transceiver is intended for battery-
powered EIA/TIA-232E and V.28/V.24 communications
interfaces that need two drivers and two receivers with
minimum power consumption. It provides a wide +1.8V
to +4.25V operating voltage range while maintaining
true RS-232 and EIA/TIA-562 voltage levels. The
MAX218 runs from two alkaline, NiCd, or NiMH cells
without any form of voltage regulator.
A shutdown mode reduces current consumption to
1μA, extending battery life in portable systems. While
shut down, all receivers can remain active or can be
disabled under logic control, permitting a system incor-
porating the CMOS MAX218 to monitor external
devices while in low-power shutdown mode.
A guaranteed 120kbps data rate provides compatibility
with popular software for communicating with personal
computers. Three-state drivers are provided on all
receiver outputs so that multiple receivers, generally of
different interface standards, can be wire-ORed at the
UART. The MAX218 is available in 20-pin DIP, SO, and
SSOP packages.
________________________Applications

Battery-Powered Equipment
Computers
Printers
Peripherals
Instruments
Modems
____________________________Features
BETTER THAN BIPOLAR!
Operates Directly from Two Alkaline, NiCd,
or NiMH Cells
+1.8V to +4.25V Supply Voltage Range120kbps Data RateLow-Cost Surface-Mount ComponentsMeets EIA/TIA-232E Specifications1μA Low-Power Shutdown ModeBoth Receivers Active During Low-Power ShutdownThree-State Receiver OutputsFlow-Through PinoutOn-Board DC-DC Converters20-Pin SSOP, Wide SO, or DIP Packages
______________Ordering Information

*Contact factory for dice specifications..8V to 4.25V-Powered,
True RS-232 Dual Transceiver
________________________________________________________________Maxim Integrated Products1

GND
C1+
GNDEN
SHDN
N.C.
TOP VIEW
C1-
T1OUT
T2OUTT2IN
T1IN
VCC
GND
R1IN
R2INR2OUT
R1OUT
DIP/SO/SSOP

MAX218
__________________Pin Configuration

T1OUT
T2OUT
T1IN
T2IN
R1OUT
R2OUT
R1IN
R2IN
GNDEN
VCC
SHDN
C1+
C1-6115, 17, 20
MAX218
ENABLE
ON/OFF
1.8V
TO
4.25V
__________Typical Operating Circuit
Call toll free 1-800-998-8800 for free samples or literature.

19-0246; Rev 1; 7/95
PARTTEMP. RANGE

MAX218CPP0°C to +70°C
MAX218C/D0°C to +70°CDice*
20 Plastic DIP
PIN-PACKAGE

MAX218CAP0°C to +70°C20 SSOP
MAX218EPP-40°C to +85°C
MAX218EAP-40°C to +85°C20 SSOP
20 Plastic DIP
MAX218EWP-40°C to +85°C20 Wide SO
MAX218CWP0°C to +70°C20 Wide SO
.8V to 4.25V-Powered,True RS-232 Dual Transceiver_______________________________________________________________________________________
ABSOLUTE MAXIMUM RATINGS
ELECTRICAL CHARACTERISTICS

(Circuit of Figure 1, VCC= 1.8V to 4.25V, C1 = 0.47μF, C2 = C3 = C4 = 1μF, L1 = 15μH, TA= TMINto TMAX, unless otherwise noted.
Typical values are at VCC= 3.0V, TA= +25°C.)
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
Supply Voltages
VCC....................................................................-0.3V to +4.6V
V+..........................................................(VCC- 0.3V) to +7.5V
V-.......................................................................+0.3V to -7.4V
VCCto V-..........................................................................+12V
LX................................................................-0.3V to (1V + V+)
Input Voltages
T_IN, EN, S—H—D—N–.................................................-0.3V to +7V
R_IN.................................................................................±25V
Output Voltages
T_OUT.............................................................................±15V)
R_OUT....................................................-0.3V to (VCC+ 0.3V)
Short-Circuit Duration, R_OUT, T_OUT to GND .......Continuous
Continuous Power Dissipation (TA= +70°C)
Plastic DIP (derate 11.11mW/°C above +70°C)..........889mW
Wide SO (derate 10.00mW/°C above +70°C)..............800mW
SSOP (derate 8.00mW/°C above +70°C)...................640mW
Operating Temperature Ranges
MAX218C_ P.....................................................0°C to +70°C
MAX218E_ P...................................................-40°C to +85°C
Storage Temperature Range ...........................-65°C to +150°C
Lead Temperature (soldering, 10sec) ...........................+300°C
All transmitter outputs loaded with 3kΩto ground
-15V < R_IN < +15V
No load, VCC= EN = S—H—D—N–= 3.0V, TA= +25°C
VCC= 1.8V to 3.6V
VCC= 1.8V to 4.25V
VCC= 1.8V to 4.25V
VCC= 2.0V to 4.25V
R_OUT, IOUT= 1.0mA
T_IN, EN, S—H—D—N–= 0V or VCC
T_IN
T_IN, EN, S—H—D—N–—H—D—N–= EN = 0V, all R_INs static—H—D—N–= 0V, EN = VCC, all R_INs static
R_OUT, 0V ≤R_OUT ≤VCC, EN = 0V
T_IN, EN, S—H—D—N–
R_OUT, IOUT= -0.4mA
CONDITIONS
±5±6Output Voltage Swing357Input Resistance0.7Input Hysteresis2.8Input Threshold High3.00.3Input Threshold Low0.4-25+25Input Voltage Range0.05±10Output Leakage CurrentVCC- 0.25VCC- 0.08Output Voltage High1.93.0Supply Current (Note 1)1.84.25Operating Voltage Range0.4Output Voltage Low0.001±1Input Leakage Current0.1Input Hysteresis0.67 x VCCInput Logic Threshold High
0.0410μA0.0410Shutdown Supply Current0.33 x VCCInput Logic Threshold Low
UNITSMINTYPMAXPARAMETER

VCC= 0V, -2V < T_OUT < +2V±24±100Output Short-Circuit Current300Output Resistance
DC CHARACTERISTICS
EIA/TIA-232E RECEIVER INPUTS
LOGIC
EIA/TIA-232E TRANSMITTER OUTPUTS
Note 1:
Entire supply current for the circuit of Figure 1.
.8V to 4.25V-Powered,True RS-232 Dual Transceiver
_______________________________________________________________________________________3
TIMING CHARACTERISTICS

(Circuit of Figure 1, VCC= 1.8V to 4.25V, C1 = 0.47μF, C2 = C3 = C4 = 1μF, L1 = 15μH, TA= TMINto TMAX, unless otherwise noted.
Typical values are at VCC= 3.0V, TA= +25°C.)
1000pF ||3kΩload each transmitter,
150pF load each receiver= +25°C, VCC= 3.0V, RL= 3kΩto 7kΩ, = 50pF to 2500pF, measured from
+3V to -3V or -3V to +3V
2500pF ||3kΩload
150pF load
150pF load
2500pF ||3kΩload
CONDITIONS
200500tDRReceiver Output Disable Time90300tER
kbps120Data Rate
Receiver Output Enable Time
V/μs3.030Transition Region Slew Rate
1.82.7tPLHTTransmitter Propagation Delay140450tETTransmitter Output Enable Time290700tPHLR
260700tPLHRReceiver Propagation Delay1.92.7tPHLT
UNITSMINTYPMAXSYMBOLPARAMETER
500tDTTransmitter Output Disable Time
______________________________________________________________Pin Description

Receiver InputsR2IN, R1IN11, 12
Transmitter Outputs; swing between V+ and V-.T2OUT, T1OUT13, 14
Negative Supply generated on-boardV-15
Terminals for Negative Charge-Pump CapacitorC1-, C1+16, 18
Positive Supply generated on-boardV+19
Ground. Connect all GND pins to ground.GND5, 17, 20
Supply Voltage Input; 1.8V to 4.25V. Bypass to GND with at least 1μF. See Capacitor
Selectionsection.VCC6
Transmitter InputsT1IN, T2IN7, 8
Receiver Outputs; swing between GND and VCC.R1OUT, R2OUT9, 10
Receiver Output Enable Control. Connect to VCCfor normal operation. Connect to GND to
force the receiver outputs into high-Z state.EN4
Shutdown Control. Connect to VCCfor normal operation. Connect to GND to shut down the
power supply and to disable the drivers. Receiver status is not changed by this control.S—H—D—N–3
PIN

Not internally connectedN.C.2
Inductor/Diode Connection PointLX1
FUNCTIONNAME
.8V to 4.25V-Powered,True RS-232 Dual Transceiver_______________________________________________________________________________________
TRANSMITTER OUTPUT VOLTAGE vs.
LOAD CAPACITANCE AT 120kbps

MAX3218-04
LOAD CAPACITANCE (pF)
(V
VOUT+
VOUT-
SLEW RATE vs.
TRANSMITTER CAPACITANCE

MAX3218-05
LOAD CAPACITANCE (pF)
(V
+SLEW
-SLEW
DATA RATE 120kbps,
TRANSMITTERS LOADED WITH
3kW PLUS INDICATED CAPACITANCE
__________________________________________Typical Operating Characteristics

(Circuit of Figure 1, VCC= 1.8V, all transmitter outputs loaded with 3kΩ, TA = +25°C, unless otherwise noted.)
SUPPLY CURRENT vs.
SUPPLY VOLTAGE
MAX3218-01
SUPPLY VOLTAGE (V)
T (m
1 TRANSMITTER FULL DATA RATE1 TRANSMITTER 1/8 DATA RATE
RL = 3kW + 2500pF
240kbps
120kbps
20kbps
0kbps
TRANSMITTING SUPPLY CURRENT
vs. LOAD CAPACITANCE
AX3218-02
LOAD CAPACITANCE (pF)
(m
20kbps
120kbps
VCC = 2.4V
TRANSMITTER 1 OPERATING AT SPECIFIED BIT RATE,
TRANSMITTER 2 OPERATING
AT 1/16 THAT RATE.
235kbps
VOH
SHDN
T_OUT
2V/div
VOL
TIME TO EXIT SHUTDOWN
(ONE TRANSMITTER HIGH,
ONE TRANSMITTER LOW)

100ms/div
VCC = 1.8V
RL = 3kW || 2500pF
.8V to 4.25V-Powered,True RS-232 Dual Transceiver
_______________________________________________________________________________________5
_______________Detailed Description

The MAX218 line driver/receiver is intended for battery-
powered EIA/TIA-232 and V.28/V.24 communications
interfaces that require two drivers and two receivers.
The operating voltage extends from 1.8V to 4.25V, yet
the device maintains true RS-232 and EIA/TIA-562
transmitter output voltage levels. This wide supply volt-
age range permits direct operation from a variety of
batteries without the need for a voltage regulator. For
example, the MAX218 can be run directly from a single
lithium cell or a pair of alkaline cells. It can also be run
directly from two NiCd or NiMH cells from full-charge
voltage down to the normal 0.9V/cell end-of-life point.
The 4.25V maximum supply voltage allows the two
rechargeable cells to be trickle- or fast-charged while
driving the MAX218.
The circuit comprises three sections: power supply,
transmitters, and receivers. The power-supply section
converts the supplied input voltage to 6.5V, providing the
voltages necessary for the drivers to meet true RS-232
levels. External components are small and inexpensive.
The transmitters and receivers are guaranteed to oper-
ate at 120kbps data rates, providing compatibility with
LapLink™ and other high-speed communications soft-
ware. A shutdown mode extends battery life by reduc-
ing supply current to 0.04μA. While shut down, all
receivers can either remain active or be disabled under
logic control. With this feature, the MAX218 can be in
low-power shutdown mode and still monitor activity on
external devices. Three-state drivers are provided on
both receiver outputs.
Switch-Mode Power Supply

The switch-mode power supply uses a single inductor
with one diode and three small capacitors to generate
±6.5V from an input voltage in the 1.8V to 4.25V
range.
Inductor Selection

Use a 15μH inductor with a saturation current rating of at
least 350mA and less than 1Ωresistance. Table 1 lists
suppliers of inductors that meet the 15μH/350mA/1Ω
specifications.
Diode Selection

Key diode specifications are fast recovery time (<10ns),
average current rating (>100mA), and peak current rat-
ing (>350mA). Inexpensive fast silicon diodes, such as
the 1N6050, are generally recommended. More expen-
sive Schottky diodes improve efficiency and give slightly
better performance at very low VCCvoltages. Table 1
lists suppliers of both surface-mount and through-hole
diodes. 1N914s are usually satisfactory, but specifica-
tions and performance vary widely with different manu-
facturers.
Capacitor Selection

Use capacitors with values at least as indicated in
Figure 1. Capacitor C2 determines the ripple on V+,
but not the absolute voltage. Capacitors C1 and C3
determine both the ripple and the absolute voltage of
V-. Bypass VCCto GND with at least 1μF (C4) placed
close to pins 5 and 6. If the VCCline is not bypassed
elsewhere (e.g., at the power supply), increase C4 to
4.7μF.
You may use ceramic or polarized capacitors in all
locations. If you use polarized capacitors, tantalum
types are preferred because of the high operating fre-
quency of the power supplies (about 250kHz). If alu-
minum electrolytics are used, higher capacitance val-
ues may be required.
™ LapLink is a trademark of Traveling Software, Inc.
T1OUT
T2OUT
T1IN
T2IN
R1OUT
R2OUT
R1IN
R2IN
GNDEN
VCC
SHDN
C1+
C1-6115, 17, 20
MAX218
ENABLE
ON/OFF
1.8V
TO
4.25VFFF
0.47mF
15mH
D1
1N6050
Figure 1.Single-Supply Operation
.8V to 4.25V-Powered,True RS-232 Dual Transceiver_______________________________________________________________________________________
RS-232 Drivers

The two drivers are identical, and deliver EIA/TIA-232E
and EIA/TIA-562 output voltage levels when VDDis
between 1.8V and 4.25V. The transmitters drive up to
3kΩin parallel with 1000pF at up to 120kbps. Connect
unused driver inputs to either GND or VCC. Disable the
drivers by takingS—H—D—N–low. The transmitter outputs are
forced into a high-impedance state whenS—H—D—N–is low.
RS-232 Receivers

The two receivers are identical, and accept both
EIA/TIA-232E and EIA/TIA-562 input signals. The
CMOS receiver outputs swing rail-to-rail. When EN is
high, the receivers are active regardless of the state of—H—D—N–. When EN is low, the receiver outputs are put
into a high-impedance state. This allows two RS-232
ports (or two ports of different types) to be wired-ORed
at the UART.
Operating Modes
—H—D—N–and EN determine the MAX218’s mode of opera-
tion, as shown in Table 2.
Table 2. Operating Modes
Shutdown

WhenS—H—D—N–is low, the power supplies are disabled and
the transmitters are put into a high-impedance state.
Receiver operation is not affected by takingS—H—D—N–low.
Power consumption is dramatically reduced in shutdown
mode. Supply current is minimized when the receiver
inputs are static in any of three states: floating (ground),
GND, or VCC.
__________Applications Information
Operation from Regulated/Unregulated
Dual System Power Supplies

The MAX218 is intended for use with three different
power-supply sources: it can be powered directly from
a battery, from a 3.0V or 3.3V power supply, or simulta-
neously from both. Figure 1 shows the single-supply
configuration. Figure 2 shows the circuit for operation
from both a 3V supply and a raw battery supply—an
ideal configuration where a regulated 3V supply is
being derived from two cells. In this application, the
MAX218’s logic levels remain appropriate for interface
with 3V logic, yet most of the power for the MAX218 is
drawn directly from the battery, without suffering the
efficiency losses of the DC-DC converter. This pro-
longs battery life.
Bypass the input supplies with 0.1μF at VCC(C4) and at
least 1μF at the inductor (C5). Increase C5 to 4.7μF if
the power supply has no other bypass capacitor con-
nected to it.
MANUFACTURERPART NUMBERPHONEFAX

Murata-ErieLQH4N150K-TAUSA (404) 436-1300
Japan (075) 951-9111
USA (404) 436-3030
Japan (075) 955-6526
SumidaCD43150USA (708) 956-0666
Japan (03) 3607-5111
USA (708) 956-0702
Japan (03) 3607-5428
TDKNLC453232T-150KUSA (708) 803-6100
Japan (03) 3278-5111
USA (708) 803-6296
Japan (03) 3278-5358
Central SemiconductorCMPSH-3, SchottkyUSA (516) 435-1110USA (516) 435-1824
MotorolaMMBD6050LT1, SiliconUSA (408) 749-0510USA (408) 991-7420
PhilipsPMBD6050, SiliconUSA (401) 762-3800USA (401) 767-4493
Motorola1N6050, Silicon
1N5817, SchottkyUSA (408) 749-0510USA (408) 991-7420
Table 1. Suggested Component SuppliersS—H—D—N–ENRECEIVER
OUTPUT
DRIVER
OUTPUT
DC-DC
CONVERTER
LHigh-ZHigh-ZOFFHEnabledHigh-ZOFFLHigh-ZEnabledONHEnabledEnabledON
SUPPLY
CURRENT

Minimum
Minimum
Normal
Normal
Inductors—Surface Mount
Diodes—Surface Mount
Diodes—Through-Hole
ic,good price


TEL:86-533-2716050      FAX:86-533-2716790
   

©2020 IC PHOENIX CO.,LIMITED