IC Phoenix
 
Home ›  MM33 > MAX192ACAP-MAX192ACWP-MAX192AEAP-MAX192AEPP-MAX192AEWP-MAX192BCAP-MAX192BCPP-MAX192BCWP-MAX192BEAP-MAX192BEPP-MAX192BEWP,Low-Power, 8-Channel, Serial 10-Bit ADC
MAX192ACAP-MAX192ACWP-MAX192AEAP-MAX192AEPP-MAX192AEWP Fast Delivery,Good Price
Part Number:
If you need More Quantity or Better Price,Welcom Any inquiry.
We available via phone +865332716050 Email
Partno Mfg Dc Qty AvailableDescript
MAX192AEPPMAXIM ?N/a5avaiLow-Power, 8-Channel, Serial 10-Bit ADC
MAX192ACAPMAXN/a61avaiLow-Power, 8-Channel, Serial 10-Bit ADC
MAX192ACAPMAXIMN/a41avaiLow-Power, 8-Channel, Serial 10-Bit ADC
MAX192ACWPMAXIMN/a2avaiLow-Power, 8-Channel, Serial 10-Bit ADC
MAX192ACWPMAXN/a1874avaiLow-Power, 8-Channel, Serial 10-Bit ADC
MAX192AEAPMAXN/a64avaiLow-Power, 8-Channel, Serial 10-Bit ADC
MAX192AEWPMAXIMN/a18avaiLow-Power, 8-Channel, Serial 10-Bit ADC
MAX192BCAPMAXN/a16avaiLow-Power, 8-Channel, Serial 10-Bit ADC
MAX192BCAPMAXIMN/a478avaiLow-Power, 8-Channel, Serial 10-Bit ADC
MAX192BCPPMAXIMN/a45avaiLow-Power, 8-Channel, Serial 10-Bit ADC
MAX192BCWPMAXIMN/a10avaiLow-Power, 8-Channel, Serial 10-Bit ADC
MAX192BEAPMAXN/a29avaiLow-Power, 8-Channel, Serial 10-Bit ADC
MAX192BEAPMAXIMN/a28avaiLow-Power, 8-Channel, Serial 10-Bit ADC
MAX192BEPPMAXIM ?N/a5avaiLow-Power, 8-Channel, Serial 10-Bit ADC
MAX192BEWPMAXIMN/a560avaiLow-Power, 8-Channel, Serial 10-Bit ADC


MAX192ACWP ,Low-Power, 8-Channel, Serial 10-Bit ADCFeaturesCH5 6 15 DOUTCH6 7 14 DGNDCH7 8 13 AGNDSee last page for Typical Operating Circuit.12AGND 9 ..
MAX192ACWP ,Low-Power, 8-Channel, Serial 10-Bit ADCApplicationsAutomotive___________________Pin ConfigurationPen-Entry SystemsTOP VIEWConsumer Electro ..
MAX192AEAP ,Low-Power, 8-Channel, Serial 10-Bit ADCMAX19219-0247; Rev. 1; 4/97Low-Power, 8-Channel,Serial 10-Bit ADC' 8-Channel Single-Ended or 4-Chan ..
MAX192AEAP+ ,Low-Power, 8-Channel, Serial 10-Bit ADCMAX19219-0247; Rev. 1; 4/97Low -Pow er, 8-Channel,Serial 10-Bit ADC♦ 8-Channel Single-Ended or 4-Ch ..
MAX192AEPP ,Low-Power, 8-Channel, Serial 10-Bit ADCELECTRICAL CHARACTERISTICS(V = 5V ±5%, f = 2.0MHz, external clock (50% duty cycle), 15 clocks/conve ..
MAX192AEPP+ ,Low-Power, 8-Channel, Serial 10-Bit ADCApplicationsAutomotive___________________Pin ConfigurationPen-Entry SystemsTOP VIEWConsumer Electro ..
MAX489 ,Low-Power, Slew-Rate-Limited RS-485/RS-422 TransceiversApplicationsMAX1487 are low-power transceivers for RS-485 and RS-MAX3430: ±80V Fault-Protected, Fai ..
MAX4890ETJ+ ,1000 Base-T, ±15kV ESD Protection LAN Switches
MAX4892ETX+ ,1000 Base-T, ±15kV ESD Protection LAN Switches
MAX4896ETP+ ,Space-Saving, 8-Channel Relay/Load DriverApplications● Industrial Equipment ● ATEV = 2.7V TO 5.5VCC● White Goods0.1µFVRELAY● Power-Grid Moni ..
MAX489CPD ,Low-Power / Slew-Rate-Limited RS-485/RS-422 TransceiversGeneral Description ________
MAX489CPD+ ,Low-Power, Slew-Rate-Limited RS-485/RS-422 TransceiversMAX481/MAX483/MAX485/MAX487–MAX491/MAX1487Low-Power, Slew-Rate-LimitedRS-485/RS-422 Transceivers


MAX192ACAP-MAX192ACWP-MAX192AEAP-MAX192AEPP-MAX192AEWP-MAX192BCAP-MAX192BCPP-MAX192BCWP-MAX192BEAP-MAX192BEPP-MAX192BEWP
Low-Power, 8-Channel, Serial 10-Bit ADC
________________General Description
The MAX192 is a low-cost, 10-bit data-acquisition system
that combines an 8-channel multiplexer, high-bandwidth
track/hold, and serial interface with high conversion
speed and ultra-low power consumption. The device
operates with a single +5V supply. The analog inputs are
software configurable for single-ended and differential
(unipolar/bipolar) operation.
The 4-wire serial interface connects directly to SPI™,
QSPI™, and Microwire™ devices, without using external
logic. A serial strobe output allows direct connection to
TMS320 family digital signal processors. The MAX192
uses either the internal clock or an external serial-
interface clock to perform successive approximation A/D
conversions. The serial interface can operate beyond
4MHz when the internal clock is used. The MAX192 has
an internal 4.096V reference with a drift of ±30ppm typi-
cal. A reference-buffer amplifier simplifies gain trim and
two sub-LSBs reduce quantization errors.
The MAX192 provides a hardwired SHDNpin and two
software-selectable power-down modes. Accessing the
serial interface automatically powers up the device, and
the quick turn-on time allows the MAX192 to be shut
down between conversions. By powering down
between conversions, supply current can be cut to
under 10µA at reduced sampling rates.
The MAX192 is available in 20-pin DIP and SO pack-
ages, and in a shrink-small-outline package (SSOP)
that occupies 30% less area than an 8-pin DIP. The
data format provides hardware and software compati-
bility with the MAX186/MAX188. For anti-aliasing filters,
consult the data sheets for the MAX291–MAX297.
________________________Applications

Automotive
Pen-Entry Systems
Consumer Electronics
Portable Data Logging
Robotics
Battery-Powered Instruments, Battery
Management
Medical Instruments
____________________________Features
8-Channel Single-Ended or 4-Channel Differential
Inputs
Single +5V OperationLow Power:1.5mA (operating)
2µA (power-down)
Internal Track/Hold, 133kHz Sampling RateInternal 4.096V Reference4-Wire Serial Interface is Compatible
with SPI, QSPI, Microwire, and TMS320
20-Pin DIP, SO, SSOP PackagesPin-Compatible 12-Bit Upgrade (MAX186/MAX188)
_______________Ordering Information
MAX192
Low-Power, 8-Channel,
Serial 10-Bit ADC
___________________Pin Configuration

SPI and QSPI are trademarks of Motorola Corp.
Microwire is a trademark of National Semiconductor Corp.
19-0247; Rev. 1; 4/97
See last page for Typical Operating Circuit.
MAX192
Low-Power, 8-Channel,
Serial 10-Bit ADC

VDDto AGND...........................................................-0.3V to +6V
AGND to DGND....................................................-0.3V to +0.3V
CH0–CH7 to AGND, DGND......................-0.3V to (VDD+ 0.3V)
CH0–CH7 Total Input Current..........................................±20mA
VREF to AGND..........................................-0.3V to (VDD+ 0.3V)
REFADJto AGND......................................-0.3V to (VDD+ 0.3V)
Digital Inputs to DGND..............................-0.3V to (VDD+ 0.3V)
Digital Outputs to DGND...........................-0.3V to (VDD+ 0.3V)
Digital Output Sink Current.................................................25mA
Continuous Power Dissipation (TA= +70°C)
Plastic DIP (derate 11.11mW/°C above +70°C).........889mW
SO (derate 10.00mW/°C above +70°C)......................800mW
SSOP (derate 8.00mW/°C above +70°C)...................640mW
CERDIP (derate 11.11mW/°C above +70°C)..............889mW
Operating Temperature Ranges
MAX192_C_P.....................................................0°C to +70°C
MAX192_E_P..................................................-40°C to +85°C
MAX192_MJP...............................................-55°C to +125°C
Storage Temperature Range............................-60°C to +150°C
Lead Temperature (soldering, 10sec)............................+300°C
ELECTRICAL CHARACTERISTICS

(VDD= 5V ±5%, fCLK= 2.0MHz, external clock (50% duty cycle), 15 clocks/conversion cycle (133ksps), 4.7µF capacitor at VREF pin,= TMINto TMAX, unless otherwise noted. Typical values are at TA= +25°C.)
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ABSOLUTE MAXIMUM RATINGS
MAX192
Low-Power, 8-Channel,
Serial 10-Bit ADC
ELECTRICAL CHARACTERISTICS (continued)

(VDD= 5V ±5%, fCLK= 2.0MHz, external clock (50% duty cycle), 15 clocks/conversion cycle (133ksps), 4.7µF capacitor at VREF pin,= TMINto TMAX, unless otherwise noted. Typical values are at TA= +25°C.)
Note 1:Tested at VDD= 5.0V; single-ended, unipolar.
Note 2:
Relative accuracy is the deviation of the analog value at any code from its theoretical value after the full-scale range has
been calibrated.
Note 3:
Grounded on-channel; sine wave applied to all off channels.
Note 4:
Conversion time defined as the number of clock cycles times the clock period; clock has 50% duty cycle.
Note 5:
Guaranteed by design. Not subject to production testing.
Note 6:
The common-mode range for the analog inputs is from AGND to VDD.
Note 7:
Sample tested to 0.1% AQL.
Note 8:
External load should not change during conversion for specified accuracy.
Note 9:
Measured at VSUPPLY+ 5% and VSUPPLY- 5% only.
MAX192
Low-Power, 8-Channel,
Serial 10-Bit ADC
ELECTRICAL CHARACTERISTICS (continued)

(VDD= 5V ±5%, fCLK= 2.0MHz, external clock (50% duty cycle), 15 clocks/conversion cycle (133ksps), 4.7µF capacitor at VREF pin,= TMINto TMAX, unless otherwise noted. Typical values are at TA= +25°C.)
Note 5:Guaranteed by design. Not subject to production testing.
MAX192
Low-Power, 8-Channel,
Serial 10-Bit ADC
TIMING CHARACTERISTICS

(VDD= 5V ±5%, TA= TMINto TMAX, unless otherwise noted.)
__________________________________________Typical Operating Characteristics
MAX192
Low-Power, 8-Channel,
Serial 10-Bit ADCs

Figure 1. Load Circuits for Enable TimeFigure 2. Load Circuits for Disabled Time
Pin Description
MAX192
Low-Power, 8-Channel,
Serial 10-Bit ADC

Figure 3.Block Diagram
Detailed Description

The MAX192 uses a successive-approximation conver-
sion technique and input track/hold (T/H) circuitry to
convert an analog signal to a 10-bit digital output. A
flexible serial interface provides easy interface to
microprocessors. No external hold capacitors are
required. Figure 3 shows the block diagram for the
MAX192.
Pseudo-Differential Input

The sampling architecture of the ADC’s analog com-
parator is illustrated in the Equivalent Input Circuit
(Figure 4). In single-ended mode, IN+ is internally
switched to CH0–CH7 and IN-is switched to AGND. In
differential mode, IN+ and IN-are selected from pairs
of CH0/CH1, CH2/CH3, CH4/CH5, and CH6/CH7. Refer
to Tables 1 and 2 to configure the channels.
In differential mode, IN-and IN+ are internally switched
to either one of the analog inputs. This configuration is
pseudo-differential to the effect that only the signal at
IN+ is sampled. The return side (IN-) must remain sta-
ble within ±0.5LSB (±0.1LSB for best results) with
respect to AGND during a conversion. Accomplish this
by connecting a 0.1µF capacitor from AIN-(the select-
ed analog input, respectively) to AGND.
During the acquisition interval, the channel selected as
the positive input (IN+) charges capacitor CHOLD. The
acquisition interval spans three SCLK cycles and ends
on the falling SCLK edge after the last bit of the input
control word has been entered. At the end of the acqui-
sition interval, the T/H switch opens, retaining charge
on CHOLDas a sample of the signal at IN+.
The conversion interval begins with the input multiplex-
er switching CHOLDfrom the positive input (IN+) to the
negative input (IN-). In single-ended mode, IN-is
simply AGND. This unbalances node ZERO at the input
of the comparator. The capacitive DAC adjusts during
the remainder of the conversion cycle to restore its
node ZERO to 0V within the limits of its resolution. This
action is equivalent to transferring a charge of
16pF x (VIN+ -VIN-) from CHOLDto the binary-weighted
capacitive DAC, which in turn forms a digital represen-
tation of the analog input signal.
Figure 4.Equivalent Input Circuit
MAX192
Track/Hold

The T/H enters its tracking mode on the falling clock
edge after the fifth bit of the 8-bit control word has been
shifted in. The T/H enters its hold mode on the falling
clock edge after the eighth bit of the control word has
been shifted in. If the converter is set up for single-ended
inputs, IN-is connected to AGND, and the converter
samples the “+” input. If the converter is set up for differ-
ential inputs, IN-connects to the “-” input, and the differ-
ence of IN+ -IN-is sampled. At the end of the conver-
sion, the positive input connects back to IN+, and
CHOLDcharges to the input signal.
The time required for the T/H to acquire an input signal is
a function of how quickly its input capacitance is charged.
If the input signal’s source impedance is high, the acquisi-
tion time lengthens and more time must be allowed
between conversions. Acquisition time is calculated by:
tAZ= 9 (RS+ RIN) 16pF
where RIN= 5kΩ, RS= the source impedance of the
input signal, and tAZ is never less than 1.5µs. Note that
source impedances below 5kW do not significantly affect
the AC performance of the ADC. Higher source imped-
ances can be used if an input capacitor is connected to
the analog inputs, as shown in Figure 5. Note that the
input capacitor forms an RC filter with the input source
impedance, limiting the ADC’s signal bandwidth.
Input Bandwidth

The ADC’s input tracking circuitry has a 4.5MHz
small-signal bandwidth, so it is possible to digitize
high-speed transient events and measure periodic sig-
nals with bandwidths exceeding the ADC’s sampling
rate by using undersampling techniques. To avoid
high-frequency signals being aliased into the frequency
band of interest, anti-alias filtering is recommended.
See the data sheets for the MAX291–MAX297 filters.
Analog Input Range and Input Protection

Internal protection diodes, which clamp the analog
input to VDDand AGND, allow the channel input pins to
swing from AGND -0.3V to VDD+ 0.3V without dam-
age. However, for accurate conversions near full scale,
the inputs must not exceed VDDby more than 50mV, or
be lower than AGND by 50mV.
If the analog input exceeds 50mV beyond the sup-
plies, do not forward bias the protection diodes of
off channels over 2mA.

The MAX192 can be configured for differential (unipolar
or bipolar) or single-ended (unipolar only) inputs, as
selected by bits 2 and 3 of the control byte (Table 3).
In the single-ended mode, set the UNI/BIP bit to unipolar.
In this mode, analog inputs are internally referenced to
AGND, with a full-scale input range from 0V to VREF.
In differential mode, both unipolar and bipolar settings
can be used. Choosing unipolar mode sets the differen-
tial input range at 0V to VREF. The output code is invalid
(code zero) when a negative differential input voltage is
applied. Bipolar mode sets the differential input range to
±VREF/ 2. Note that in this differential mode, the com-
mon-mode input range includes both supply rails. Refer
to Tables 4a and 4b for input voltage ranges.
Quick Look

To evaluate the analog performance of the MAX192
quickly, use Figure 5’s circuit. The MAX192 requires a
control byte to be written to DIN before each
conversion. Tying DIN to +5V feeds in control bytes of
Low-Power, 8-Channel,
Serial 10-Bit ADC
Table 1.Channel Selection in Single-Ended Mode (SGL/DIF= 1)
MAX192
Low-Power, 8-Channel,
Serial 10-Bit ADC
Table 3.Control-Byte Format
Table 2.Channel Selection in Differential Mode (SGL/DIF= 0)
MAX192
Low-Power, 8-Channel,
Serial 10-Bit ADC

$FF (HEX), which trigger single-ended conversions on
CH7 in external clock mode without powering down
between conversions. In external clock mode, the
SSTRB output pulses high for one clock period before
the most significant bit of the conversion result comes
out of DOUT. Varying the analog input to CH7 should
alter the sequence of bits from DOUT. A total of 15
clock cycles is required per conversion. All transitions
of the SSTRB and DOUT outputs occur on the falling
edge of SCLK.
How to Start a Conversion

A conversion is started on the MAX192 by clocking
a control byte into DIN. Each rising edge on SCLK,
with CSlow, clocks a bit from DIN into the MAX192’s
internal shift register. After CSfalls, the first arriving
logic “1” bit defines the MSB of the control byte. Until
this first “start” bit arrives, any number of logic “0” bits
can be clocked into DIN with no effect. Table 3 shows
the control-byte format.
The MAX192 is compatible with Microwire, SPI, and
QSPI devices. For SPI, select the correct clock polarity
and sampling edge in the SPI control registers: set
CPOL = 0 and CPHA = 0. Microwire and SPI both
transmit a byte and receive a byte at the same time.
Using the Typical Operating Circuit, the simplest soft-
ware interface requires only three 8-bit transfers to per-
form a conversion (one 8-bit transfer to configure the
ADC, and two more 8-bit transfers to clock out the
12-bit conversion result).
Example: Simple Software Interface

Make sure the CPU’s serial interface runs in master
mode so the CPU generates the serial clock. Choose a
clock frequency from 100kHz to 2MHz.Set up the control byte for external clock mode,
call it TB1. TB1 should be of the format:
1XXXXX11 binary, where the Xs denote the par-
ticular channel and conversion-mode selected.Use a general-purpose I/O line on the CPU to
pull CSon the MAX192 low.Transmit TB1 and simultaneously receive a byte
and call it RB1. Ignore RB1.Transmit a byte of all zeros ($00 HEX) and
simultaneously receive byte RB2.Transmit a byte of all zeros ($00 HEX) and
simultaneously receive byte RB3.Pull CSon the MAX192 high.
Figure 6 shows the timing for this sequence. Bytes RB2
and RB3 will contain the result of the conversion
padded with one leading zero, two sub-LSB bits, and
three trailing zeros. The total conversion time is a func-
tion of the serial clock frequency and the amount of
dead time between 8-bit transfers. Make sure that the
total conversion time does not exceed 120µs, to avoid
excessive T/H droop.
Digital Output

In unipolar input mode, the output is straight binary
(Figure 15). For bipolar inputs in differential mode, the
output is twos-complement (Figure 16). Data is clocked
out at the falling edge of SCLK in MSB-first format.
Internal and External Clock Modes

The MAX192 may use either an external serial clock or
the internal clock to perform the successive-approxima-
tion conversion. In both clock modes, the external clock
shifts data in and out of the MAX192. The T/H acquires
the input signal as the last three bits of the control byte
are clocked into DIN. Bits PD1 and PD0 of the control
byte program the clock mode. Figures 7 through 10
show the timing characteristics common to both
modes.
Table 4a.Unipolar Full Scale and Zero
Scale
External Clock
In external clock mode, the external clock not only
shifts data in and out, it also drives the analog-to-digital
conversion steps. SSTRB pulses high for one clock
period after the last bit of the control byte.
Successive-approximation bit decisions are made and
appear at DOUT on each of the next 12 SCLK falling
edges (see Figure 6). The first 10 bits are the true data
bits, and the last two are sub-LSB bits.
SSTRB and DOUT go into a high-impedance state whengoes high; after the next CSfalling edge, SSTRB will
output a logic low. Figure 8 shows the SSTRB timing in
external clock mode.
The conversion must complete in some minimum time, or
else droop on the sample-and-hold capacitors may
degrade conversion results. Use internal clock mode if the
clock period exceeds 10µs, or if serial-clock interruptions
could cause the conversion interval to exceed 120µs.
Internal Clock

In internal clock mode, the MAX192 generates its own
conversion clock internally. This frees the microproces-
sor from the burden of running the SAR conversion
clock, and allows the conversion results to be read
back at the processor’s convenience, at any clock rate
from zero to typically 10MHz. SSTRB goes low at the
start of the conversion and then goes high when the
conversion is complete. SSTRB will be low for a maxi-
mum of 10µs, during which time SCLK should remain
low for best noise performance. An internal register
stores data when the conversion is in progress. SCLK
clocks the data out at this register at any time after the
conversion is complete. After SSTRB goes high, the
next falling clock edge will produce the MSB of the
conversion at DOUT, followed by the remaining bits in
MSB-first format (Figure 9). CSdoes not need to be
held low once a conversion is started.
MAX192
Low-Power, 8-Channel,
Serial 10-Bit ADC

Figure 5.Quick-Look Circuit
MAX192
Low-Power, 8-Channel,
Serial 10-Bit ADC

Figure 6. 24-Bit External Clock Mode Conversion Timing (SPI, QSPI and Microwire Compatible)
Figure 7. Detailed Serial-Interface Timing
Pulling CShigh prevents data from being clocked into
the MAX192 and three-states DOUT, but it does not
adversely affect an internal clock-mode conversion
already in progress. When internal clock mode is
selected, SSTRB does not go into a high-impedance
state when CSgoes high.
Figure 10 shows the SSTRB timing in internal clock
mode. In internal clock mode, data can be shifted in
and out of the MAX192 at clock rates exceeding
4.0MHz, provided that the minimum acquisition time,
tAZ, is kept above 1.5µs.
Data Framing

The falling edge ofCSdoes notstart a conversion on
the MAX192. The first logic high clocked into DIN is inter-
preted as a start bit and defines the first bit of the control
byte. A conversion starts on the falling edge of SCLK,
after the eighth bit of the control byte (the PD0 bit) is
clocked into DIN. The start bit is defined as:
The first high bit clocked into DIN withCSlow any-
time the converter is idle, e.g. after VDDis applied.
The first high bit clocked into DIN after bit 3 of a
conversion in progress is clocked onto the DOUT pin.
If a falling edge onCSforces a start bit before bit 3
(B3) becomes available, then the current conversion
will be terminated and a new one started. Thus, the
fastest the MAX192 can run is 15 clocks per conver-
sion. Figure 11a shows the serial-interface timing nec-
essary to perform a conversion every 15 SCLK cycles
in external clock mode. If CSis low and SCLK is contin-
uous, guarantee a start bit by first clocking in 16 zeros.
ic,good price


TEL:86-533-2716050      FAX:86-533-2716790
   

©2020 IC PHOENIX CO.,LIMITED