IC Phoenix
 
Home ›  MM22 > MAX1112CAP-MAX1112EAP-MAX1113EEE-MAX1113EPE,+5V, Low-Power, Multi-Channel, Serial 8-Bit ADCs
MAX1112CAP-MAX1112EAP-MAX1113EEE-MAX1113EPE Fast Delivery,Good Price
Part Number:
If you need More Quantity or Better Price,Welcom Any inquiry.
We available via phone +865332716050 Email
Partno Mfg Dc Qty AvailableDescript
MAX1112CAPMAXIN/a98avai+5V, Low-Power, Multi-Channel, Serial 8-Bit ADCs
MAX1112CAPMAXN/a22avai+5V, Low-Power, Multi-Channel, Serial 8-Bit ADCs
MAX1112CAPMAXIMN/a11avai+5V, Low-Power, Multi-Channel, Serial 8-Bit ADCs
MAX1112EAPMAXIMN/a5avai+5V, Low-Power, Multi-Channel, Serial 8-Bit ADCs
MAX1113EEEMAXIM N/a93avai+5V, Low-Power, Multi-Channel, Serial 8-Bit ADCs
MAX1113EEEMAXN/a14avai+5V, Low-Power, Multi-Channel, Serial 8-Bit ADCs
MAX1113EPEMAXIMN/a1500avai+5V, Low-Power, Multi-Channel, Serial 8-Bit ADCs


MAX1113EPE ,+5V, Low-Power, Multi-Channel, Serial 8-Bit ADCsELECTRICAL CHARACTERISTICS(V = +4.5V to +5.5V; unipolar input mode; COM = 0V; f = 500kHz, external ..
MAX1115EKA+T ,Single-Supply, Low-Power, Serial 8-Bit ADCsApplicationsLow-Power, Hand-Held Portable DevicesPIN- TOP PART TEMP RANGEPACK A G E M A RKSystem D ..
MAX1116EKA+T ,Single-Supply, Low-Power, Serial 8-Bit ADCsFeaturesThe MAX1115/MAX1116 low-power, 8-bit, analog-to-♦ Single Supplydigital converters (ADCs) fe ..
MAX1117EKA+T ,Single-Supply, Low-Power, 2-Channel, Serial 8-Bit ADCsApplicationsOrdering InformationLow-Power, Handheld Portable DevicesPIN- TOP PART TEMP. RANGESystem ..
MAX1118EKA ,Single-Supply, Low-Power, 2-Channel, Serial 8-Bit ADCsFeaturesThe MAX1117/MAX1118/MAX1119 low-power, 8-bit, Single Supplydual-channel, analog-to-digital ..
MAX1118EKA-T ,Single-Supply, Low-Power, 2-Channel, Serial 8-Bit ADCsFeaturesThe MAX1117/MAX1118/MAX1119 low-power, 8-bit,♦ Single Supplydual-channel, analog-to-digital ..
MAX3468CSA+ ,+5V, Fail-Safe, 40Mbps, PROFIBUS RS-485/RS-422 Transceivers
MAX3471CUA ,1.6A / RS-485/RS-422 / Half-Duplex / Differential Transceiver for Battery-Powered Systems
MAX3471CUA ,1.6A / RS-485/RS-422 / Half-Duplex / Differential Transceiver for Battery-Powered Systems
MAX3471CUA+ ,1.6µA, RS-485/RS-422, Half Duplex, Differential Transceiver for Battery-Powered Systems
MAX3471CUA+T ,1.6µA, RS-485/RS-422, Half Duplex, Differential Transceiver for Battery-Powered Systems
MAX3471EUA ,1.6A / RS-485/RS-422 / Half-Duplex / Differential Transceiver for Battery-Powered Systems


MAX1112CAP-MAX1112EAP-MAX1113EEE-MAX1113EPE
+5V, Low-Power, Multi-Channel, Serial 8-Bit ADCs
General Description
The MAX1112/MAX1113 are low-power, 8-bit, 8-chan-
nel analog-to-digital converters (ADCs) that feature an
internal track/hold, voltage reference, clock, and serial
interface. They operate from a single +4.5V to +5.5V
supply and consume only 135µA while sampling at
rates up to 50ksps. The MAX1112’s 8 analog inputs
and the MAX1113’s 4 analog inputs are software-con-
figurable, allowing unipolar/bipolar and single-
ended/differential operation.
Successive-approximation conversions are performed
using either the internal clock or an external serial-inter-
face clock. The full-scale analog input range is deter-
mined by the 4.096V internal reference, or by an
externally applied reference ranging from 1V to VDD.
The 4-wire serial interface is compatible with the SPI™,
QSPI™, and MICROWIRE™ serial-interface standards.
A serial-strobe output provides the end-of-conversion
signal for interrupt-driven processors.
The MAX1112/MAX1113 have a software-program-
mable, 2µA automatic power-down mode to minimize
power consumption. Using power-down, the supply
current is reduced to 13µA at 1ksps, and only 82µA at
10ksps. Power-down can also be controlled using the
SHDNinput pin. Accessing the serial interface automat-
ically powers up the device.
The MAX1112 is available in 20-pin SSOP and DIP
packages. The MAX1113 is available in small 16-pin
QSOP and DIP packages.
________________________Applications

Portable Data Logging
Hand-Held Measurement Devices
Medical Instruments
System Diagnostics
Solar-Powered Remote Systems
4–20mA-Powered Remote
Data-Acquisition Systems
____________________________Features
+4.5V to +5.5V Single SupplyLow Power: 135µA at 50ksps
13µA at 1ksps
8-Channel Single-Ended or 4-Channel Differential
Inputs (MAX1112)
4-Channel Single-Ended or 2-Channel Differential
Inputs (MAX1113)
Internal Track/Hold; 50kHz Sampling RateInternal 4.096V ReferenceSPI/QSPI/MICROWIRE-Compatible Serial InterfaceSoftware-Configurable Unipolar or Bipolar InputsTotal Unadjusted Error:±1LSB (max)
±0.3LSB (typ)
MAX1112/MAX1113
+5V, Low-Power, Multi-Channel,
Serial 8-Bit ADCs
Functional Diagram
Pin Configurations appear at end of data sheet.

SPI and QSPI are trademarks of Motorola, Inc.
MICROWIRE is a trademark of National Semiconductor Corp.
MAX1112/MAX1113
+5V, Low-Power, Multi-Channel,
Serial 8-Bit ADCs
ABSOLUTE MAXIMUM RATINGS

Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
VDDto AGND..............................................................-0.3V to 6V
AGND to DGND.......................................................-0.3V to 0.3V
CH0–CH7, COM, REFIN,
REFOUT to AGND...................................-0.3V to (VDD+ 0.3V)
Digital Inputs to DGND...............................................-0.3V to 6V
Digital Outputs to DGND............................-0.3V to (VDD+ 0.3V)
Continuous Power Dissipation (TA= +70°C)
16 Plastic DIP (derate 10.53mW/°C above +70°C)......842mW
16 QSOP (derate 8.30mW/°C above +70°C)................667mW
16 CERDIP (derate 10.00mW/°C above +70°C) ..........800mW
20 Plastic DIP (derate 11.11mW/°C above +70°C)......889mW
20 SSOP (derate 8.00mW/°C above +70°C)................640mW
20 CERDIP (derate 11.11mW/°C above +70°C) ..........889mW
Operating Temperature Ranges
MAX1112C_P/MAX1113C_E................................0°C to +70°C
MAX1112E_P/MAX1113E_E.............................-40°C to +85°C
MAX1112MJP/MAX1113MJE..........................-55°C to +125°C
Storage Temperature Range.............................-65°C to +150°C
Lead Temperature (soldering, 10sec).............................+300°C
ELECTRICAL CHARACTERISTICS

(VDD= +4.5V to +5.5V; unipolar input mode; COM = 0V; fSCLK= 500kHz, external clock (50% duty cycle); 10 clocks/conversion
cycle (50ksps); 1µF capacitor at REFOUT; TA= TMIN toTMAX; unless otherwise noted.)
MAX1112/MAX1113
+5V, Low-Power, Multi-Channel,
Serial 8-Bit ADCs
ELECTRICAL CHARACTERISTICS (continued)

(VDD= +4.5V to +5.5V; unipolar input mode; COM = 0V; fSCLK= 500kHz, external clock (50% duty cycle); 10 clocks/conversion
cycle (50ksps); 1µF capacitor at REFOUT; TA= TMIN toTMAX; unless otherwise noted.)
MAX1112/MAX1113
+5V, Low-Power, Multi-Channel,
Serial 8-Bit ADCs
ELECTRICAL CHARACTERISTICS (continued)

(VDD= +4.5V to +5.5V; unipolar input mode; COM = 0V; fSCLK= 500kHz, external clock (50% duty cycle); 10 clocks/conversion
cycle (50ksps); 1µF capacitor at REFOUT; TA= TMIN toTMAX; unless otherwise noted.)
MAX1112/MAX1113
+5V, Low-Power, Multi-Channel,
Serial 8-Bit ADCs
TIMING CHARACTERISTICS (Figures 8 and 9)

(VDD= +4.5V to +5.5V, TA= TMINto TMAX,unless otherwise noted.)
Note 1:
Relative accuracy is the analog value’s deviation (at any code) from its theoretical value after the full-scale range is calibrated.
Note 2:
VREFIN= 4.096V, offset nulled.
Note 3:
On-channel grounded; sine wave applied to all off-channels.
Note 4:
Conversion time is defined as the number of clock cycles multiplied by the clock period; clock has 50% duty cycle.
Note 5:
Guaranteed by design. Not subject to production testing.
Note 6:
Common-mode range for the analog inputs is from AGND to VDD.
Note 7:
External load should not change during the conversion for specified accuracy.
Note 8:
External reference at 4.096V, full-scale input, 500kHz external clock.
Note 9:
Measured as |VFS (4.5V) - VFS(5.5V) |.
Note 10:
1µF at REFOUT; internal reference settling to 0.5LSB.
MAX1112/MAX1113
+5V, Low-Power, Multi-Channel,
Serial 8-Bit ADCs
__________________________________________Typical Operating Characteristics

(VDD= +5.0V; fSCLK = 500kHz; external clock (50% duty cycle); RL= ¥; TA = +25°C, unless otherwise noted.)
MAX1112/MAX1113
+5V, Low-Power, Multi-Channel,
Serial 8-Bit ADCs
Pin Description

Figure 1. Load Circuits for Enable Time
Figure 2. Load Circuits for Disable Time
MAX1112/MAX1113
+5V, Low-Power, Multi-Channel,
Serial 8-Bit ADCs
_______________Detailed Description

The MAX1112/MAX1113 analog-to-digital converters
(ADCs) use a successive-approximation conversion
technique and input track/hold (T/H) circuitry to convert
an analog signal to an 8-bit digital output. A flexible seri-
al interface provides easy interface to microprocessors
(µPs). Figure 3 shows the Typical Operating Circuit.
Pseudo-Differential Input

The sampling architecture of the ADC’s analog com-
parator is illustrated in Figure 4, the equivalent input cir-
cuit. In single-ended mode, IN+ is internally switched to
the selected input channel, CH_, and IN- is switched to
COM. In differential mode, IN+ and IN- are selected
from the following pairs: CH0/CH1, CH2/CH3,
CH4/CH5, and CH6/CH7. Configure the MAX1112
channels with Table 1 and the MAX1113 channels with
Table 2.
In differential mode, IN- and IN+ are internally switched
to either of the analog inputs. This configuration is
pseudo-differential to the effect that only the signal at
IN+ is sampled. The return side (IN-) must remain sta-
ble within ±0.5LSB (±0.1LSB for best results) with
respect to AGND during a conversion. To accomplish
this, connect a 0.1µF capacitor from IN- (the selected
analog input) to AGND if necessary.
During the acquisition interval, the channel selected as
the positive input (IN+) charges capacitor CHOLD. The
acquisition interval spans two SCLK cycles and ends
on the falling SCLK edge after the last bit of the input
control word has been entered. At the end of the acqui-
sition interval, the T/H switch opens, retaining charge
on CHOLDas a sample of the signal at IN+.
The conversion interval begins with the input multiplex-
er switching CHOLDfrom the positive input (IN+) to the
negative input (IN-). In single-ended mode, IN- is sim-
ply COM. This unbalances node ZERO at the input of
the comparator. The capacitive DAC adjusts during the
remainder of the conversion cycle to restore node
ZERO to 0V within the limits of 8-bit resolution. This
action is equivalent to transferring a charge of 18pF x
(VIN+- VIN-) from CHOLDto the binary-weighted capac-
itive DAC, which in turn forms a digital representation of
the analog input signal.
Track/Hold

The T/H enters its tracking mode on the falling clock
edge after the sixth bit of the 8-bit control byte has
been shifted in. It enters its hold mode on the falling
clock edge after the eighth bit of the control byte has
been shifted in. If the converter is set up for single-
ended inputs, IN- is connected to COM, and the con-
verter samples the “+” input; if it is set up for differential
inputs, IN- connects to the “-” input, and the difference
(IN+ - IN-) is sampled. At the end of the conversion, the
positive input connects back to IN+, and CHOLD
charges to the input signal.
Figure 3. Typical Operating Circuit
Figure 4. Equivalent Input Circuit
MAX1112/MAX1113
+5V, Low-Power, Multi-Channel,
Serial 8-Bit ADCs
Table 1a. MAX1112 Channel Selection in Single-Ended Mode (SGL/DIF= 1)
Table 1b. MAX1112 Channel Selection in Differential Mode (SGL/DIF= 0)
Table 2a. MAX1113 Channel Selection in Single-Ended Mode (SGL/DIF= 1)
Table 2b. MAX1113 Channel Selection in Differential Mode (SGL/DIF= 0)
MAX1112/MAX1113
+5V, Low-Power, Multi-Channel,
Serial 8-Bit ADCs
Table 3.Control-Byte Format

The time required for the T/H to acquire an input signal
is a function of how quickly its input capacitance is
charged. If the input signal’s source impedance is high,
the acquisition time lengthens, and more time must be
allowed between conversions. The acquisition time,
tACQ, is the minimum time needed for the signal to be
acquired. It is calculated by:
tACQ= 6 x (RS+ RIN) x 18pF
where RIN= 6.5kΩ, RS= the source impedance of the
input signal, and tACQis never less than 1µs. Note that
source impedances below 2.4kΩdo not significantly
affect the AC performance of the ADC.
Input Bandwidth

The ADC’s input tracking circuitry has a 1.5MHz small-
signal bandwidth, so it is possible to digitize high-
speed transient events and measure periodic signals
with bandwidths exceeding the ADC’s sampling rate by
using undersampling techniques. To avoid high-
frequency signals being aliased into the frequency
band of interest, anti-alias filtering is recommended.
Analog Inputs

Internal protection diodes, which clamp the analog
input to VDDand AGND, allow the channel input pins to
swing from (AGND - 0.3V) to (VDD+ 0.3V) without dam-
age. However, for accurate conversions near full scale,
the inputs must not exceed VDDby more than 50mV or
be lower than AGND by 50mV.
If the analog input exceeds 50mV beyond the sup-
plies, do not forward bias the protection diodes of
off channels over 2mA.

The MAX1112/MAX1113 can be configured for differen-
tial or single-ended inputs with bits 2 and 3 of the con-
trol byte (Table 3). In single-ended mode, analog inputs
are internally referenced to COM with a full-scale input
range from COM to VREFIN + COM. For bipolar opera-
tion, set COM to VREFIN/ 2.
In differential mode, choosing unipolar mode sets the
differential input range at 0V to VREFIN. In unipolar
mode, the output code is invalid (code zero) when a
negative differential input voltage is applied. Bipolar
mode sets the differential input range to ±VREFIN/ 2.
Note that in this mode, the common-mode input range
includes both supply rails. Refer to Table 4 for input
voltage ranges.
Quick Look

To quickly evaluate the MAX1112/MAX1113’s analog
performance, use the circuit of Figure 5. The
MAX1112/MAX1113 require a control byte to be written
to DIN before each conversion. Tying DIN to +5V feeds
ic,good price


TEL:86-533-2716050      FAX:86-533-2716790
   

©2020 IC PHOENIX CO.,LIMITED