M74HCT273 ,OCTAL D TYPE FLIP FLOP WITH CLEARM74HCT273OCTAL D TYPE FLIP FLOP WITH CLEAR ■ HIGH SPEED : ..
M74HCT273M1R ,OCTAL D TYPE FLIP FLOP WITH CLEARM74HCT273OCTAL D TYPE FLIP FLOP WITH CLEAR ■ HIGH SPEED : ..
M74HCT273RM13TR ,OCTAL D TYPE FLIP FLOP WITH CLEARAbsolute Maximum Ratings are those values beyond which damage to the device may occur. Functional o ..
M74HCT32M1R ,QUAD 2-INPUT OR GATEM74HCT32QUAD 2-INPUT OR GATE ■ HIGH SPEED: t = 13ns (TYP.) at V = 4.5VPD CC■ LOW POWER DISSIPATION ..
M74HCT32RM13TR ,QUAD 2-INPUT OR GATEAbsolute Maximum Ratings are those values beyond which damage to the device may occur. Functional o ..
M74HCT367 ,HCT367 NON INVERTING, HCT368 INVERTING HEX BUS BUFFER (3-STATE)M74HCT367HEX BUS BUFFERWITH 3 STATE OUTPUT NON INVERTING ■ HIGH SPEED: t = 14ns (TYP.) at V = 4.5V ..
MAX1512ETA+ ,EEPROM-Programmable TFT VCOM CalibratorELECTRICAL CHARACTERISTICS (continued)(Circuit of Figure 1, V = 3V, V = 10V, V = 5V, R = 30.1kΩ , T ..
MAX1512ETA+T ,EEPROM-Programmable TFT VCOM CalibratorFeaturesThe MAX1512 is a programmable VCOM-adjustment♦ 7-Bit Adjustable Sink-Current Outputsolution ..
MAX1513ETP ,2.7 to 5.5 V, TFT-LCD power-supply controllerFeatures♦ 2.7V to 5.5V Input Supply RangeThe MAX1513/MAX1514 provide complete power-sup-ply solutio ..
MAX1513ETP+ ,TFT-LCD Power-Supply ControllersFeatures♦ 2.7V to 5.5V Input Supply RangeThe MAX1513/MAX1514 provide complete power-sup-ply solutio ..
MAX1513ETP+T ,TFT-LCD Power-Supply ControllersELECTRICAL CHARACTERISTICS(Circuit of Figure 1, V = 3V, V = 10V, SDFR = IN, C = 0.22µF, T = 0°C to ..
MAX1515ETG ,+1.3 V to +3.6 V, Low-voltage, internal switch, step-down/DDR regulatorfeatures dual internal♦ 1MHz Maximum Switching Frequencyn-channel MOSFET power switches for high ef ..
M74HCT273
OCTAL D TYPE FLIP FLOP WITH CLEAR
1/10August 2001 HIGH SPEED :
fMAX = 80 MHz (TYP.) at VCC = 4.5V LOW POWER DISSIPATION:CC =4μA(MAX.) at TA =25°C COMPATIBLE WITH TTL OUTPUTS : IH = 2V (MIN.) VIL = 0.8V (MAX) SYMMETRICAL OUTPUT IMPEDANCE:OH | = IOL = 4mA (MIN) BALANCED PROPAGATION DELAYS:
tPLH ≅ tPHL PIN AND FUNCTION COMPATIBLE WITH
74 SERIES 273
DESCRIPTIONThe M74HCT273 is an high speed CMOS OCTAL
D TYPE FLIP FLOP WITH CLEAR fabricated with
silicon gate C2 MOS technology.
Information signals applied to D inputs are
transferred to the Q outputs on the positive-going
edge of the clock pulse.
When the CLEAR input is held low, the Q output
are in the low logic level independent of the other
inputs.
All inputs are equipped with protection circuits
against static discharge and transient excess
voltage.
M74HCT273OCTAL D TYPE FLIP FLOP WITH CLEAR
PIN CONNECTION AND IEC LOGIC SYMBOLS
ORDER CODES
M74HCT2732/10
INPUT AND OUTPUT EQUIVALENT CIRCUIT PIN DESCRIPTION
TRUTH TABLE X : Don’t Care
LOGIC DIAGRAM This logic diagram has not be used to estimate propagation delays
M74HCT2733/10
ABSOLUTE MAXIMUM RATINGS Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is
not implied
(*) 500mW at 65 °C; derate to 300mW by 10mW/°C from 65°C to 85°C
RECOMMENDED OPERATING CONDITIONS
DC SPECIFICATIONS
M74HCT2734/10
AC ELECTRICAL CHARACTERISTICS (CL = 50 pF, Input tr = tf = 6ns)
CAPACITIVE CHARACTERISTICS 1) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without
load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. ICC(opr) = CPD x VCC x fIN + ICC/8 (per FLIP
FLOP), and the total CPD when n pcs of FLIP FLOP operate can be gained by the following equations: CPD (total) = 32 + 11 x n
M74HCT2735/10
TEST CIRCUIT CL = 50pF or equivalent (includes jig and probe capacitance)
RT = ZOUT of pulse generator (typically 50Ω)
WAVEFORM 1: PROPAGATION DELAY TIME, MINIMUM PULSE WIDTH (CLOCK), SETUP AND
HOLD TIME (nD TO CLOCK), CLOCK MAXIMUM FREQUENCY (f=1MHz; 50% duty cycle)
M74HCT2736/10
WAVEFORM 2 :PROPAGATION DELAY TIME (f=1MHz; 50% duty cycle)
WAVEFORM 3 : MINIMUM PULSE WIDTH (CLEAR), MINIMUM REMOVAL TIME (CLEAR TO
CLOCK)(f=1MHz; 50% duty cycle)
