M74HC86M1R ,QUAD EXCLUSIVE OR GATEABSOLUTE MAXIMUM RATINGS Symbol Parameter Value UnitV Supply Voltage-0.5 to +7 VCCV DC Input V ..
M74HC86M1R ,QUAD EXCLUSIVE OR GATEAbsolute Maximum Ratings are those values beyond which damage to the device may occur. Functional o ..
M74HC86RM13TR ,QUAD EXCLUSIVE OR GATEM74HC86QUAD EXCLUSIVE OR GATE ■ HIGH SPEED:t = 12ns (TYP.) at V = 6VPD CC■ LOW POWER DISSIPATION:I ..
M74HCT00 ,QUAD 2-INPUT NAND GATEM74HCT00QUAD 2-INPUT NAND GATE ■ HIGH SPEED: t = 12ns (TYP.) at V = 4.5VPD CC■ LOW POWER DISSIPATI ..
M74HCT00RM13TR ,QUAD 2-INPUT NAND GATEM74HCT00QUAD 2-INPUT NAND GATE ■ HIGH SPEED: t = 12ns (TYP.) at V = 4.5VPD CC■ LOW POWER DISSIPATI ..
M74HCT00TTR ,QUAD 2-INPUT NAND GATEAbsolute Maximum Ratings are those values beyond which damage to the device may occur. Functional o ..
MAX15013AASA+T ,175V/2A, High-Speed, Half-Bridge MOSFET DriversApplicationsOrdering InformationTelecom Half-Bridge Power SuppliesPIN- PKGPART TEMP RANGETwo-Switch ..
MAX15013BASA+T ,175V/2A, High-Speed, Half-Bridge MOSFET Driversapplications. These♦ Up to 175V Input Operationdrivers are independently controlled and their 35ns ..
MAX1501ETE+T ,Highly Integrated, Linear Battery Charger with Thermal Regulation for Portable ApplicationsFeatures The MAX1501 intelligent, constant-current, constant- ♦ Stand-Alone 1-Cell Li+ Charging, M ..
MAX15023ETG+ ,Wide 4.5V to 28V Input, Dual-Output Synchronous Buck ControllerFeatures● 5.5V to 28V or 5V ±10% Input Supply RangeThe MAX15023 dual, synchronous step-down control ..
MAX15023ETG+T ,Wide 4.5V to 28V Input, Dual-Output Synchronous Buck ControllerElectrical Characteristics(V = 12V, R = 33kΩ, C = 4.7µF, C = 1µF, T = -40°C to +85°C, unless otherw ..
MAX15024AATB+T ,Single/Dual, 16ns, High Sink/Source Current Gate DriversFeaturesThe MAX15024/MAX15025 single/dual, high-speed♦ 8A Peak Sink Current/4A Peak Source CurrentM ..
M74HC86M1R-M74HC86RM13TR
QUAD EXCLUSIVE OR GATE
1/8July 2001 HIGH SPEED:
tPD = 12ns (TYP.) at VCC = 6V LOW POWER DISSIPATION:CC = 1μA(MAX.) at TA =25°C HIGH NOISE IMMUNITY:NIH = VNIL = 28 % VCC (MIN.) SYMMETRICAL OUTPUT IMPEDANCE:
|IOH| = IOL = 4mA (MIN) BALANCED PROPAGATION DELAYS:
tPLH ≅ tPHL WIDE OPERATING VOLTAGE RANGE:CC (OPR) = 2V to 6V PIN AND FUNCTION COMPATIBLE WITH
74 SERIES 86
DESCRIPTIONThe M74HC86 is an high speed CMOS QUAD
EXCLUSIVE OR GATE fabricated with silicon
gate C2 MOS technology.
Input and output buffer are installed, which
enables high noise immunity and stable output.
All inputs are equipped with protection circuits
against static discharge and transient excess
voltage.
M74HC86QUAD EXCLUSIVE OR GATE
PIN CONNECTION AND IEC LOGIC SYMBOLS
ORDER CODES
M74HC862/8
INPUT AND OUTPUT EQUIVALENT CIRCUIT PIN DESCRIPTION
TRUTH TABLE
ABSOLUTE MAXIMUM RATINGS Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is
not implied
(*) 500mW at 65 °C; derate to 300mW by 10mW/°C from 65°C to 85°C
RECOMMENDED OPERATING CONDITIONS
M74HC863/8
DC SPECIFICATIONS
AC ELECTRICAL CHARACTERISTICS (CL = 50 pF, Input tr = tf = 6ns)
CAPACITIVE CHARACTERISTICS 1) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without
load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. ICC(opr) = CPD x VCC x fIN + ICC/4 (per gate)
M74HC864/8
TEST CIRCUIT CL = 50pF or equivalent (includes jig and probe capacitance)
RT = ZOUT of pulse generator (typically 50Ω)
WAVEFORM : PROPAGATION DELAY TIME (f=1MHz; 50% duty cycle)
