M74HC374RM13TR ,OCTAL D-TYPE FLIP FLOP WITH 3 STATE OUTPUT (NON INVERTING)Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional o ..
M74HC377M1R ,OCTAL D TYPE FLIP FLOPM74HC377OCTAL D TYPE FLIP FLOP ■ HIGH SPEED : f = 66 ..
M74HC390M1R ,DUAL DECADE COUNTERM74HC390DUAL DECADE COUNTER ■ HIGH SPEED : f = 79 M ..
M74HC390RM13TR ,DUAL DECADE COUNTERlogic diagram has not be used to estimate propagation delays3/12M74HC390TIMING CHART
M74HC393B1R ,DUAL BINARY COUNTERABSOLUTE MAXIMUM RATINGS Symbol Parameter Value UnitV Supply Voltage-0.5 to +7 VCCV DC Input V ..
M74HC393M1R ,DUAL BINARY COUNTERM74HC393DUAL BINARY COUNTER ■ HIGH SPEED : f = 79 M ..
MAX1458CAE ,1%-Accurate / Digitally Trimmed Sensor Signal ConditionerApplicationsI.C. 3 14 INPPiezoresistive Pressure and AccelerationTEMP 4 MAX1458 13 BDRIVETransducer ..
MAX1459AAP ,2-Wire, 4-20mA Smart Signal ConditionerFeaturesThe MAX1459 highly integrated analog-sensor signal Highly Integrated Sensor Signal Conditi ..
MAX1459AAP+ ,2-Wire, 4-20mA Smart Signal ConditionerFeaturesThe MAX1459 highly integrated analog-sensor signal♦ Highly Integrated Sensor Signal Conditi ..
MAX145ACUA ,+2.7V, Low-Power, 2-Channel, 108ksps, Serial 12-Bit ADCs in 8-Pin レMAXApplications MAX144ACPA 0°C to +70°C 8 Plastic DIP ±0.5MAX144BCPA 0°C to +70°C 8 Plastic DI ..
MAX145ACUA ,+2.7V, Low-Power, 2-Channel, 108ksps, Serial 12-Bit ADCs in 8-Pin レMAXapplications, or for other circuits withINLdemanding power-consumption and space require-PART TEMP. ..
MAX145AEUA ,+2.7V, Low-Power, 2-Channel, 108ksps, Serial 12-Bit ADCs in 8-Pin レMAXFeaturesThe MAX144/MAX145 low-power, 12-bit analog-to-' Single-Supply Operation (+2.7V to +5.25V)di ..
M74HC374M1R-M74HC374RM13TR
OCTAL D-TYPE FLIP FLOP WITH 3 STATE OUTPUT (NON INVERTING)
1/11July 2001 HIGH SPEED:
fMAX = 90MHz (TYP.) at VCC = 6V LOW POWER DISSIPATION:CC = 4μA(MAX.) at TA =25°C HIGH NOISE IMMUNITY:NIH = VNIL = 28 % VCC (MIN.) SYMMETRICAL OUTPUT IMPEDANCE:
|IOH| = IOL = 6mA (MIN) BALANCED PROPAGATION DELAYS:
tPLH ≅ tPHL WIDE OPERATING VOLTAGE RANGE:CC (OPR) = 2V to 6V PIN AND FUNCTION COMPATIBLE WITH
74 SERIES 374
DESCRIPTIONThe M74HC374 is an high speed CMOS OCTAL
D-TYPE FLIP FLOP WITH 3-STATE OUTPUTS
NON INVERTING fabricated with sub-micron
silicon gate C2 MOS technology.
This 8 bit D-TYPE FLIP FLOP is controlled by a
clock input (CK) and an output enable input (OE).
On the positive transition of the clock, the Q
outputs will be set to the logic state that were
setup at the D inputs.
While the OE input is at low level, the eight outputs
will be in a normal logic state (high or low logic
level) and while OE is high the outputs will be in
a high impedance state.
The output control does not affect the internal
operation of flip-flops; that is, the old data can be
retained or the new data can be entered even
while the outputs are off.
All inputs are equipped with protection circuits
against static discharge and transient excess
voltage.
M74HC374OCTAL D-TYPE FLIP FLOP
WITH 3 STATE OUTPUT NON INVERTING
PIN CONNECTION AND IEC LOGIC SYMBOLS
ORDER CODES
M74HC3742/11
INPUT AND OUTPUT EQUIVALENT CIRCUIT PIN DESCRIPTION
TRUTH TABLE X: Don’t Care
Z: High Impedance
LOGIC DIAGRAM This logic diagram has not be used to estimate propagation delays
M74HC3743/11
ABSOLUTE MAXIMUM RATINGS Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is
not implied
(*) 500mW at 65 °C; derate to 300mW by 10mW/°C from 65°C to 85°C
RECOMMENDED OPERATING CONDITIONS
M74HC3744/11
DC SPECIFICATIONS
M74HC3745/11
AC ELECTRICAL CHARACTERISTICS (CL = 50 pF, Input tr = tf = 6ns)
CAPACITIVE CHARACTERISTICS 1) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without
load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. ICC(opr) = CPD x VCC x fIN + ICC/8 (per Flip
Flop) and the CPD when n pcs of Flip Flop operate, can be gained by the following equation: CPD(TOTAL) = 30 + 17 x n (pF)
M74HC3746/11
TEST CIRCUIT CL = 50pF/150pF or equivalent (includes jig and probe capacitance)
R1 = 1KΩ or equivalent
RT = ZOUT of pulse generator (typically 50Ω)
WAVEFORM 1: CK TO Qn PROPAGATION DELAYS, CK FMAX, Dn TO CK SETUP AND HOLD
TIMES (f=1MHz; 50% duty cycle)
