M74HC365RM13TR ,BUS BUFFER (3-STATE) (NON INVERTING)ABSOLUTE MAXIMUM RATINGS Symbol Parameter ValueUnitV Supply Voltage-0.5 to +7 VCCV DC Input Vo ..
M74HC365TTR ,BUS BUFFER (3-STATE) (NON INVERTING)M74HC365HEX BUS BUFFER WITH 3 STATE OUTPUTS (NON INVERTING) ■ HIGH SPEED:t = 10ns (TYP.) at V = 6V ..
M74HC366M1R ,HEX BUS BUFFER (3-STATE)M74HC366HEX BUS BUFFER WITH 3 STATE OUTPUTS (INVERTING) ■ HIGH SPEED:t = 10ns (TYP.) at V = 6VPD C ..
M74HC367M1R ,NON INVERTING HEX BUS BUFFER (3-STATE)M74HC367HEX BUS BUFFERWITH 3 STATE OUTPUT NON INVERTING ■ HIGH SPEED: t = 9ns (TYP.) at V = 6VPD C ..
M74HC367RM13TR ,NON INVERTING HEX BUS BUFFER (3-STATE)Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional o ..
M74HC367TTR ,NON INVERTING HEX BUS BUFFER (3-STATE)ABSOLUTE MAXIMUM RATINGS Symbol Parameter Value UnitV Supply Voltage-0.5 to +7 VCCV DC Input V ..
MAX14527ETA+ ,Adjustable Overvoltage Protector with High AccuracyFeaturesThe MAX14527/MAX14528 overvoltage protection♦ Input Voltage Protection Up to +28Vdevices fe ..
MAX14527ETA+T ,Adjustable Overvoltage Protector with High AccuracyMAX14527/MAX1452819-4357; Rev 0; 10/08Adjustable Overvoltage Protectorwith High Accuracy
MAX14528ETA+T ,Adjustable Overvoltage Protector with High AccuracyApplications Ordering InformationCell PhonesTOP OVLOPART PIN-PACKAGEMARK (V)Media PlayersMAX14527ET ..
MAX1452AAE ,Low-Cost Precision Sensor Signal Conditionerblock diagram appears at the end of data sheet.Transducers and Transmitters Strain GaugesPin Config ..
MAX1452AAE+ ,Low-Cost Precision Sensor Signal ConditionerBlock Diagram and Pin Configurations appear at ● Accelerometersthe end of data sheet.● Humidity Sen ..
MAX1452AAE+T ,Low-Cost Precision Sensor Signal ConditionerElectrical Characteristics(V = V = +5V, V = 0V, T = +25°C, unless otherwise noted.)DD DDF SS APARAM ..
M74HC365M1R-M74HC365RM13TR -M74HC365TTR
BUS BUFFER (3-STATE) (NON INVERTING)
1/10July 2001 HIGH SPEED:
tPD = 10ns (TYP.) at VCC = 6V LOW POWER DISSIPATION:
ICC = 4μA(MAX.) at TA=25°C HIGH NOISE IMMUNITY:
VNIH = VNIL = 28 % VCC (MIN.) SYMMETRICAL OUTPUT IMPEDANCE:OH | = IOL = 6mA (MIN) BALANCED PROPAGATION DELAYS: PLH ≅ t PHL WIDE OPERATING VOLTAGE RANGE:CC (OPR) = 2V to 6V PIN AND FUNCTION COMPATIBLE WITH
74 SERIES 365
DESCRIPTIONThe 74HC365 is an advanced high-speed CMOS
HEX BUS BUFFER (3-STATE) fabricated with
silicon gate C2 MOS technology.
All six buffers are controlled by the combination of
two enable inputs (G1 and G2); all outputs of
these buffers are enabled only when both G1 and
G2 inputs are held low, under all other conditions
these outputs are disabled in a high-impedance
state.
The M74HC365 has non inverting outputs.
All inputs are equipped with protection circuits
against static discharge and transient excess
voltage.
M74HC365HEX BUS BUFFER
WITH 3 STATE OUTPUTS (NON INVERTING)
PIN CONNECTION AND IEC LOGIC SYMBOLS
ORDER CODES
M74HC3652/10
INPUT AND OUTPUT EQUIVALENT CIRCUIT PIN DESCRIPTION
TRUTH TABLE X : Don’t Care
Z : High Impedance
ABSOLUTE MAXIMUM RATINGS Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is
not implied
(*) 500mW at 65 °C; derate to 300mW by 10mW/°C from 65°C to 85°C
RECOMMENDED OPERATING CONDITIONS
M74HC3653/10
DC SPECIFICATIONS
M74HC3654/10
AC ELECTRICAL CHARACTERISTICS (CL = 50 pF, Input tr = tf = 6ns)
CAPACITIVE CHARACTERISTICS 1) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without
load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. ICC(opr) = CPD x VCC x fIN + ICC/6 (per gate)
M74HC3655/10
TEST CIRCUIT CL = 50pF/150pF or equivalent (includes jig and probe capacitance)
R1 = 1KΩ or equivalent
RT = ZOUT of pulse generator (typically 50Ω)
WAVEFORM 1: PROPAGATION DELAY TIMES (f=1MHz; 50% duty cycle)
M74HC3656/10
WAVEFORM 2 : OUTPUT ENABLE AND DISABLE TIMES (f=1MHz; 50% duty cycle)
