IC Phoenix
 
Home ›  MM4 > M27V322-100B1-M27V322-100F1,32 MBIT (2MB X16) LOW VOLTAGE UV EPROM AND OTP EPROM
M27V322-100B1-M27V322-100F1 Fast Delivery,Good Price
Part Number:
If you need More Quantity or Better Price,Welcom Any inquiry.
We available via phone +865332716050 Email
Partno Mfg Dc Qty AvailableDescript
M27V322-100B1 |M27V322100B1STN/a146avai32 MBIT (2MB X16) LOW VOLTAGE UV EPROM AND OTP EPROM
M27V322-100F1 |M27V322100F1STN/a5380avai32 MBIT (2MB X16) LOW VOLTAGE UV EPROM AND OTP EPROM


M27V322-100F1 ,32 MBIT (2MB X16) LOW VOLTAGE UV EPROM AND OTP EPROMapplications where the content is programmedEM27V322only one time and erasure is not required, theM ..
M27W016-100M1 ,16 MBIT (1MB X16) 3V SUPPLY FLEXIBLEROM™ MEMORYAbsolute Maximum Ratings 15DC and AC PARAMETERS . 16Table 8. Operating and AC Measuremen ..
M27W064 ,64 MBIT (4MB X16) 3V SUPPLY FLEXIBLEROM?MEMORYAbsolute Maximum Ratings 14DC and AC PARAMETERS . 15Table 8. Operating and AC Measuremen ..
M27W064-100M1 ,64 MBIT (4MB X16) 3V SUPPLY FLEXIBLEROM™ MEMORYAbsolute Maximum Ratings 14DC and AC PARAMETERS . 15Table 8. Operating and AC Measuremen ..
M27W10180K6 ,1 MBIT (128KB X8) LOW VOLTAGE UV EPROM AND OTP EPROMLogic DiagramDESCRIPTIONThe M27W101 is a low voltage 1 Mbit EPROM of-fered in two range UV (ultra v ..
M27W10180K6 ,1 MBIT (128KB X8) LOW VOLTAGE UV EPROM AND OTP EPROMAbsolute Maximum Ratings Symbol Parameter Value Unit(3)T –40 to 85 °CA Ambient Operating Temperatur ..
M48T201V ,3.3V-5V TIMEKEEPER CONTROLLERAbsolute Maximum Ratings(Table2.) .... ...... ....... ...... ....... ...... ...... .....7DC AND AC ..
M48T201V85MH1 ,3.3V-5V TIMEKEEPER SupervisorAbsolute Maximum Ratings . . . . . . . 24DC AND AC PARAMETERS . 25Table 11. DC and AC Mea ..
M48T201V85MH1 ,3.3V-5V TIMEKEEPER SupervisorFEATURES SUMMARY . . . . . 1Figure 1. Package . . . . . . . 1DESCRIPTION . . . ..
M48T201V-85MH1 ,3.3V-5V TIMEKEEPER SupervisorLogic Diagram . . 4Table 1. Signal Names . . 4Figure 3. SOIC Connections . . . . ..
M48T201V-85MH1E ,3.3V-5V TIMEKEEPER SupervisorFEATURES SUMMARY■ CONVERTS LOW POWER SRAM INTO Figure 1. PackageNVRAMs■ YEAR 2000 COMPLIANTSNAPHAT ..
M48T201V-85MH1F ,3.3V-5V TIMEKEEPER SupervisorM48T201YM48T201V®5.0 or 3.3V TIMEKEEPER Supervisor


M27V322-100B1-M27V322-100F1
32 MBIT (2MB X16) LOW VOLTAGE UV EPROM AND OTP EPROM
1/14March 2001
M27V322

32 Mbit (2Mb x16) Low Voltage UV EPROM and OTP EPROM 3.3V ± 10% SUPPLY VOLTAGE in READ
OPERATION READ ACCESS TIME 100ns at VCC = 3.0V to 3.6V PIN COMPATIBLE WITH M27C322 WORD-WIDE CONFIGURABLE 32 Mbit MASK ROM REPLACEMENT LOW POWER CONSUMPTION Active Current 30mA at 5MHz Stand-by Current 60μA PROGRAMMING VOLTAGE: 12V ± 0.25V PROGRAMMING TIME: 50μs/word ELECTRONIC SIGNATURE Manufacturer Code: 0020h Device Code: 0034h
DESCRIPTION

The M27V322 is a 32 Mbit EPROM offered in the
UV range (ultra violet erase) and OTP range. It is
ideally suited for microprocessor systems requir-
ing large data or program storage. It is organised
as 2 MWords of 16 bit. The pin-out is compatible
with a 32 Mbit Mask ROM.
The FDIP42W (window ceramic frit-seal package)
has a transparent lid which allows the user to ex-
pose the chip to ultraviolet light to erase the bit pat-
tern. A new pattern can then be written rapidly to
the device by following the programming proce-
dure.
For applications where the content is programmed
only one time and erasure is not required, the
M27V322 is offered in PDIP42 and SDIP42 pack-
ages.
M27V322
from E to output (tELQV). Data is available at the
output after a delay of tGLQV from the falling edge
of GVPP, assuming that E has been low and the
addresses have been stable for at least tAVQV-
tGLQV.
Standby Mode

The M27V322 has a standby mode which reduces
the supply current from 30mA to 30μA. The
M27V322 is placed in the standby mode by apply-
ing a CMOS high signal to the E input.When in the
standby mode, the outputs are in a high imped-
ance state, independent of the GVPP input.
Two Line Output Control

Because EPROMs are usually used in larger
memory arrays, this product features a 2 line con-
trol function which accommodates the use of mul-
tiple memory connection. The two line control
function allows: the lowest possible memory power dissipation, complete assurance that output bus contention
will not occur.
For the most efficient use of these two control
lines, E should be decoded and used as the prima-
ry device selecting function, while GVPP should be
made a common connection to all devices in the
array and connected to the READ line from the
system control bus. This ensures that all deselect-
ed memory devices are in their low power standby
mode and that the output pins are only active
when data is required from a particular memory
device.
Table 1. Signal Names
DEVICE OPERATION

The operating modes of the M27V322 are listed in
the Operating Modes Table. A single power supply
is required in the read mode. All inputs are TTL
compatible except for VPP and 12V on A9 for the
Electronic Signature.
Read Mode

The M27V322 has a word-wide organization. Chip
Enable (E) is the power control and should be
used for device selection. Output Enable (G) is the
output control and should be used to gate data to
the output pins independent of device selection.
Assuming that the addresses are stable, the ad-
dress access time (tAVQV) is equal to the delay
3/14
M27V322
Table 2. Absolute Maximum Ratings (1)

Note:1. Except for the rating "Operating Temperature Range", stresses above those listed in the Table "Absolute Maximum Ratings" may
cause permanent damage to the device. These are stress ratings only and operation of the device at these or any other conditions
above those indicated in the Operating sections of this specification is not implied. Exposure to Absolute Maximum Rating condi-
tions for extended periods may affect device reliability. Refer also to the STMicroelectronics SURE Program and other relevant qual-
ity documents. Minimum DC voltage on Input or Output is –0.5V with possible undershoot to –2.0V for a period less than 20ns. Maximum DC
voltage on Output is VCC +0.5V with possible overshoot to VCC +2V for a period less than 20ns. Depends on range.
Table 3. Operating Modes

Note: X = VIH or VIL, VID = 12V ± 0.5V.
Table 4. Electronic Signature

Note: Outputs Q15-Q8 are set to '0'.
M27V322
Table 5. AC Measurement Conditions
Table 6. Capacitance (1)
(TA = 25 °C, f = 1 MHz)
Note:1. Sampled only, not 100% tested.
put control and by properly selected decoupling
capacitors. It is recommended that a 0.1μF ceram-
ic capacitor is used on every device between VCC
and VSS. This should be a high frequency type of
low inherent inductance and should be placed as
close as possible to the device. In addition, a
4.7μF electrolytic capacitor should be used be-
tween VCC and VSS for every eight devices. This
capacitor should be mounted near the power sup-
ply connection point. The purpose of this capacitor
is to overcome the voltage drop caused by the in-
ductive effects of PCB traces.
System Considerations

The power switching characteristics of Advanced
CMOS EPROMs require careful decoupling of the
supplies to the devices. The supply current ICC
has three segments of importance to the system
designer: the standby current, the active current
and the transient peaks that are produced by the
falling and rising edges of E. The magnitude of the
transient current peaks is dependent on the ca-
pacitive and inductive loading of the device out-
puts. The associated transient voltage peaks can
be suppressed by complying with the two line out-
5/14
M27V322
Table 7. Read Mode DC Characteristics (1)

(TA = –40 to 85 °C or 0 to 70 °C; VCC = 3.3V ± 10%; VPP = VCC)
Note:1. VCC must be applied simultaneously with or before VPP and removed simultaneously or after VPP. Maximum DC voltage on Output is VCC +0.5V.
Table 8. Read Mode AC Characteristics (1)

(TA = –40 to 85 °C or 0 to 70 °C; VCC = 3.3V ± 10%; VPP = VCC)
Note:1. VCC must be applied simultaneously with or before VPP and removed simultaneously or after VPP Sampled only, not 100% tested. Speed obtained with High Speed measurement conditions.
M27V322
Table 9. Programming Mode DC Characteristics (1)

(TA = 25 °C; VCC = 6.25V ± 0.25V; VPP = 12V ± 0.25V)
Note:1. VCC must be applied simultaneously with or before VPP and removed simultaneously or after VPP.
7/14
M27V322
Table 10. MARGIN MODE AC Characteristics (1)

(TA = 25 °C; VCC = 6.25V ± 0.25V; VPP = 12V ± 0.25V)
Note:1. VCC must be applied simultaneously with or before VPP and removed simultaneously or after VPP.
Table 11. Programming Mode AC Characteristics (1)

(TA = 25 °C; VCC = 6.25V ± 0.25V; VPP = 12V ± 0.25V)
Note:1. VCC must be applied simultaneously with or before VPP and removed simultaneously or after VPP. Sampled only, not 100% tested.
Programming

When delivered (and after each erasure for UV
EPROM), all bits of the M27V322 are in the "1"
state. Data is introduced by selectively program-
ming "0"s into the desired bit locations. Although
only "0"s will be programmed, both "1"s and "0"s
can be present in the data word. The only way to
change a "0" to a "1" is by die exposition to ultravi-
olet light (UV EPROM). The M27V322 is in the
programming mode when VPP input is at 12.V,
GVPP is at VIH and E is pulsed to VIL. The data to
be programmed is applied to 16 bits in parallel to
the data output pins. The levels required for the
address and data inputs are TTL. VCC is specified
to be 6.25V ± 0.25V.
ic,good price


TEL:86-533-2716050      FAX:86-533-2716790
   

©2020 IC PHOENIX CO.,LIMITED