L9222D ,QUAD INVERTING TRANSISTOR SWITCHFEATURESFigure 1. Packages■ OUTPUT VOLTAGE TO 50V■ OUTPUT CURRENT TO 1.2A■ VERY LOW SATURATION VOLT ..
L9305A ,DUAL HIGH CURRENT RELAY DRIVERblock diagram unless otherwise5 ambspecified)Symbol Parameter Test Conditions Min. Typ. Max. UnitV5 ..
L9308 ,DUAL LOW SIDE DRIVERL9308DUAL LOW SIDE DRIVER. DARLINGTON OUTPUT STAGE. INPUT COMPARATOR WITH WIDE RANGECOMMON MODE OPE ..
L9308 ,DUAL LOW SIDE DRIVERL9308DUAL LOW SIDE DRIVER. DARLINGTON OUTPUT STAGE. INPUT COMPARATOR WITH WIDE RANGECOMMON MODE OPE ..
L9308 ,DUAL LOW SIDE DRIVERBLOCK DIAGRAMOctober 1990 1/7This is advanced information on a new product now in development or un ..
L9332 ,Quad Intelligent Power Low Side SwitchFeaturesThe L9332 is a monolithic integrated quad low A Quad power low side driver with 3output s ..
LC7365N ,DTMF Tone Generator for Pushbutton TelephoneBlock DiagramLC7365NLC7366NLC7365N,7366Nf-- _.lJl,'7 Bl-, I [---"e-o XMITJ: , Trununk01: " Mute I3. ..
LC7366N ,DTMF Tone Generator for Pushbutton TelephoneFeatures. Low voltage CMOS process, for direct operation from telephone line. The L07365N can inter ..
LC7366NM ,DTMF Tone Generator for Pushbutton TelephoneFeaturesq High-density miniflat package (MFP-20). Low voltage CMOS process for direct operation fro ..
LC7366NM ,DTMF Tone Generator for Pushbutton Telephonel OEEring number:EN 2888A 1CMOS LSILC7365NM, 7366NMDTMF Tone Generatorfor Pushbutton TelephoneNo.28 ..
LC7367 ,DTMF/PULSE Switchable DialerFeatures(1) Low voltage CMOS process for direct operation from telephone line.(2) Possible to use s ..
LC7367J ,DTMF/PULSE Switchable DialerFeaturesPackage Dimensions• Low voltage CMOS process for direct operation from tele-unit:mmphone li ..
L9222D
QUAD INVERTING TRANSISTOR SWITCH
1/7
L9222May 2004
FEATURES OUTPUT VOLTAGE TO 50V OUTPUT CURRENT TO 1.2A VERY LOW SATURATION VOLTAGE TTL COMPATIBLE INPUTS INTEGRAL SUPPRESSION DIODE
DESCRIPTIONThe L9222 monolithic quad transistor switch is de-
signed for high current, high voltage switching ap-
plications.
Each of the four switches is controlled by a logic
input and all four are controlled by a common en-
able input. All inputs are TTL-compatible for direct
connection to logic circuits. Each switch consists
of an open-collector transistor plus a clamp diode
for applications with inductive loads.
The emitters of the four switches are connected to-
gether to GND. The switches of the same device
may be paralled. The device is intended to drive
coils such as relays, solenoids, unipolar stepper
motors, LED etc.
QUAD INVERTING TRANSISTOR SWITCH
Figure 2. BLOCK DIAGRAMREV. 3
L9222
Table 2. ABSOLUTE MAXIMUM RATINGS
Figure 3. PIN CONNECTION (Top view)
Table 3. TRUTH TABLEFor each input :
H= High level
L= Low level
X = Don’t care
Table 4. THERMAL DATA
3/7
L9222
Table 5. ELECTRICAL CHARACTERISTICS VCC = 5Vdc ± 5% VEN = 5V – 40 ≤ Tj ≤ 125°C unless otherwise specified
L9222
Figure 4. Powerdip (12+2+2 0Mechanical Data & Package Dimensions
5/7
L9222
Figure 5. SO20L Mechanical Data & Package Dimensions
L9222
Table 6. Revision History
