IC Phoenix
 
Home ›  K > K1 > 18pcs of K3022PG,Optocouplers
K3022PG from IC-PHOENIX Fast Delivery,Good Price
Part Number:
If you need more quantity or better price,Welcom Any inquiry.
We available via phone +865332796365 Email
K3022PG 18pcs , DIP6,Optocouplers
Partno Mfg Dc Qty Available
K3022PG N/a 18
K3022PG from VIS, 45pcs,Optocouplers
K3022PG from VISHAY, Vishay 1260pcs,Optocouplers

Rev. 1.9, 26-Oct-04 3K3020P/ K3020PG SeriesVishay SemiconductorsRSTest condition:dV/dtcrV = 2/3 VS DRM(Sine wave)R =33kV~LI dV/dtFT crqV =30VeffRL(Sine wave)R =2kL95 10813Figure 1. Test circuit for dV/dt and dV/dtcr crq95 10814I ≥ IF FTI =0Fdv/dt dv/dtcrq crdv/dt Highest value of the “rate of rise of off-state voltage” which does not cause any switching from thecroff-state to the on-statedv/dt Highest value of the “rate of rise of communicating voltage” which does not switch on the device again,crqafter the voltage has decreased to zero and the trigger current is switched from I to zeroFTFigure 2. 270+5 VMVAC ~0.1 µFTTLGalvanic separation95 10815Figure 3. Motor control circuit Document Number 835052 Rev. 1.9, 26-Oct-04K3020P/ K3020PG SeriesVishay SemiconductorsFeatures • Isolation materials according to UL 94-VO~ ~6 54  Pollution degree 2 (DIN/VDE 0110 resp. IEC 60664)17221  Climatic classification 55/100/21 (IEC 60068 part 1)1 2 3  Special construction: Therefore, extra low cou-A (+) C (–) ncpling capacity of typical 0.2 pF, high Common Note: Pin 5 must not be connectedMode Rejection I offered into 4 groupsFT  Rated impulse voltage (transient overvoltage) Pbe3V = 6 kV peak Pb-freeIOTM  Isolation test voltage (partial discharge test volt- Circuits for safe protective separation against electri-age) V = 1.6 kV cal shock according to safety class II (reinforced iso-pdlation):  Rated isolation voltage (RMS includes DC) V = 600 V (848 V peak)  For appl. class I - IV at mains voltage ≤ 300 VIOWM RMS  Rated recurring peak voltage (repetitive)  For appl. class I - III at mains voltage ≤ 600 V accord-V = 600 V ing to DIN EN 60747-5-2(VDE0884)/ DIN EN 60747-IORM RMS5-5 pending, table 2, suitable for.  Thickness through insulation ≥ 0.75 mm  Creepage current resistance according to VDE 0303/IEC 60112 Comparative Tracking Order InformationIndex: CTI = 275Part Remarks  Lead-free componentK3020P I < 30 mA, V = 400 V, DIP-6 300 milFT DRM  Component in accordance to RoHS 2002/95/EC K3021P I < 15 mA, V = 400 V, DIP-6 300 milFT DRMand WEEE 2002/96/ECK3022P I < 10 mA, V = 400 V, DIP-6 300 milFT DRMAgency Approvals K3023P I < 5 mA, V = 400 V, DIP-6 300 milFT DRM  UL1577, File No. E76222 System Code C, Double K3036P I < 3.6 mA, V = 400 V, DIP-6 300 milFT DRMProtectionK3020PG I < 30 mA, V = 400 V, DIP-6 400 milFT DRM  BSI: BS EN 41003, BS EN 60095 (BS 415), BS EN K3021PG I < 15 mA, V = 400 V, DIP-6 400 milFT DRM60950 (BS 7002), Certificate number 7081 and K3022PG I < 10 mA, V = 400 V, DIP-6 400 milFT DRM7402K3023PG I < 5 mA, V = 400 V, DIP-6 400 mil  DIN EN 60747-5-2 (VDE0884) FT DRMDIN EN 60747-5-5 pendingK3036PG I < 3.6 mA, V = 400 V, DIP-6 400 milFT DRM  FIMKO (SETI): EN 60950, Certificate No. 12398G = Leadform 10.16 mm; G is not marked on the body

K3023P ,OptocouplersElectrical CharacteristicsT = 25 °C, unless otherwise specifiedambMinimum and maximum values are te ..
K3023P ,Optocouplers Document Number 835054 Rev. 1.9, 26-Oct-04K3020P/ K3020PG SeriesVishay SemiconductorsMaximum Safet ..
K3023PG ,OptocouplersApplicationsDescriptionMonitorsThe K3020P/ K3020PG series consists of a pho-Air conditionerstotrans ..
K3296 ,MOS FIELD EFFECT TRANSISTORELECTRICAL CHARACTERISTICS(TA = 25°C)CHARACTERISTICS SYMBOL TEST CONDITIONS MIN. TYP. MAX. UNITDrai ..
K3351K ,TECHNIK - HIGH RELIABILITY FOR LOW COST
KCF25A20 , FRD - Low Forward Voltage Drop
KCF25A20 , FRD - Low Forward Voltage Drop
KCH20A10 , Low Forward Voltage Drop Diode
ic,good price


TEL:86-533-2796365      FAX:86-533-2716790
   

©2018 IC PHOENIX CO.,LIMITED