IC Phoenix
 
Home ›  DD32 > DS5001FP,128K Soft Microprocessor Chip
DS5001FP Fast Delivery,Good Price
Part Number:
If you need More Quantity or Better Price,Welcom Any inquiry.
We available via phone +865332716050 Email
Partno Mfg Dc Qty AvailableDescript
DS5001FPDALLASN/a1000avai128K Soft Microprocessor Chip


DS5001FP ,128K Soft Microprocessor Chipfeatures include the ability to save the operating state, power-fail reset, power-fail interrupt, a ..
DS5001FP-16 ,128k Soft Microprocessor ChipFEATURES PIN ASSIGNMENT (Top View) 8051-compatible microprocessor adapts to itstask– Accesses up t ..
DS5001FP-16+ ,128k Soft Microprocessor ChipFEATURES PIN CONFIGURATIONS  8051-Compatible Microprocessor Adapts to Its TOP VIEWTask  Acc ..
DS5001FP-16N+ ,128k Soft Microprocessor Chipfeatures include the ability to save the operating state, power-fail reset, power-fail interrupt, a ..
DS5002FM-C03 ,Secure Microprocessor ChipApplications microprocessor chip. In addition to the memory and Access 32kB, 64kB, or 128kB of NV S ..
DS5002FMN-16 ,Secure microprocessor chip, 8051-compatible, in-system programming, 16 MHzFEATURES The DS5002FP secure microprocessor chip is a  8051-Compatible Microprocessor for secure ..
EC3H06B ,NPN Epitaxial Planar Silicon Transistor UHF to S Band Low-Noise Amplifier and OSC ApplicationsFeatures Package Dimensions · Low noise : NF=0.9dB typ (f=1GHz).unit:mm: NF=1.4dB typ (f=1.5GHz).21 ..
EC4H07C ,Ultrahigh-Frequency TransistorsFeatures Package Dimensions•Low noise : NF=1.5dB typ (f=2GHz). unit : mm•High cut-off frequency : f ..
ECH8401 ,Medium Output MOSFETsAbsolute Maximum Ratings at Ta=25°CParameter Symbol Conditions Ratings UnitDrain-to-Source Voltage ..
ECH8402 ,Medium Output MOSFETsAbsolute Maximum Ratings at Ta=25°CParameter Symbol Conditions Ratings UnitDrain-to-Source Voltage ..
ECH8402 ,Medium Output MOSFETsOrdering number : ENN8148 ECH8402N-Channel Silicon MOSFETGeneral-Purpose Switching DeviceECH8402App ..
ECH8410 ,N-Channel Power MOSFET, 30V, 12A, 10mOhm, Single ECH8Maximum RatingsParameter Symbol Conditions Ratings UnitDrain-to-Source Voltage V 30 VDSSGate-to-Sou ..


DS5001FP
128K Soft Microprocessor Chip
FEATURES 8051-Compatible Microprocessor Adapts to Its
Task
Accesses up to 128kB of nonvolatile SRAM In-system programming through on-chip
serial port Can modify its own program or data memory Accesses memory on a separate byte-wide bus Performs CRC-16 check of NV RAM
memory Decodes memory and peripheral chip enables High-Reliability Operation Maintains all nonvolatile resources for over
10 years Power-fail reset Early warning power-fail interrupt Watchdog timer Lithium backs user SRAM for program/data
storage Precision bandgap reference for power
monitor Fully 8051 Compatible 128kB scratchpad RAM Two timer/counters On-chip serial port 32 parallel I/O port pins
Software Security Available with DS5002FP
Secure Microprocessor

This data sheet must be used in conjunction with the Secure
Microcontroller User’s Guide, available on our website at
/microcontrollers. The user’s guide contains

operating information, whereas the data sheet contains ordering
information, pinout, and electrical specifications
PIN CONFIGURATIONS

DS5001FP
128k Soft Microprocessor Chip

P0.4AD4
CE2
PE2
BA9
P0.3/AD3
BA8
P0.2/AD2
BA13
P0.1/AD1
R/W
P0.0/AD0
VCC0
VCC
MSEL
P1.0
BA14
P1.1
BA12
P1.2
BA7
P1.3
PE3
PE4
BA6
P2.6/A14
CE3
CE4
BD3
P2.5/A13
BD2
P2.4/A12
BD1
P2.3/A11
BD0
VLI
BA15
GND
P2.2/A10
P2.1/A9
P2.0/A8
XTAL1
XTAL2
P3.7/RD
P3.6/WR
P3.5/TI
PF
VRST
P3.4/T0
DS5001FP

P1.4
BA5
P1.5
BA4
P1.6
BA3
P1.7
PROG
BA2
RST
BA1
P3.0/RXD
BA0
P3.1/TXD
P3.2/INT0P3.3/INT1
BA11 P0.5/AD5 PE1 P0.6/AD6 BA10 P0.7/AD7 CE1 N.C. CE1N BD7 ALE BD6 PSEN BD5 P2.7/A15 BD4
25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65
MQFP
MQFP

TOP VIEW
DS5001FP
ORDERING INFORMATION
PART TEMP RANGE MAX CLOCK
SPEED (MHz)
PIN-
PACKAGE

DS5001FP-16 0°C to +70°C 16 80 MQFP
DS5001FP-16+ 0°C to +70°C 16 80 MQFP
DS5001FP-16N -40°C to +85°C 16 80 MQFP
DS5001FP-16N+ -40°C to +85°C 16 80 MQFP
DS5001FP-12-44 0°C to +70°C 12 44MQFP
DS5001FP-12-44+ 0°C to +70°C 12 44 MQFP
+ Denotes a Pb-free/RoHS-compliant device.
DESCRIPTION

The DS5001FP 128k soft microprocessor chip is an 8051-compatible microprocessor based on NV RAM
technology and designed for systems that need large quantities of nonvolatile memory. It provides full
compatibility with the 8051 instruction set, timers, serial port, and parallel I/O ports. By using NV RAM
instead of ROM, the user can program and then reprogram the microprocessor while in-system. The
application software can even change its own operation, which allows frequent software upgrades,
adaptive programs, customized systems, etc. In addition, by using NV SRAM, the DS5001FP is ideal for
data logging applications. It also connects easily to a Dallas real-time clock.
The DS5001FP provides the benefits of NV RAM without using I/O resources. It uses a nonmultiplexed
byte-wide address and data bus for memory access. This bus performs all memory access and provides
decoded chip enables for SRAM, which leaves the 32 I/O port pins free for application use. The
DS5001FP uses ordinary SRAM and battery-backs the memory contents for over 10 years at room
temperature with a small external battery. A DS5001FP also provides high-reliability operation in harsh
environments. These features include the ability to save the operating state, power-fail reset, power-fail
interrupt, and watchdog timer.
A user programs the DS5001FP through its on-chip serial bootstrap loader. The bootstrap loader
supervises the loading of software into NV RAM, validates it, and then becomes transparent to the user.
Software can be stored in multiple 32kB or one 128kB CMOS SRAM(s). Using its internal partitioning,
the DS5001FP can divide a common RAM into user-selectable program and data segments. This partition
can be selected at program loading time, but can then be modified later at any time. The microprocessor
decodes memory access to the SRAM and addresses memory through its byte-wide bus. Memory portions
designated code or ROM are automatically write-protected by the microprocessor. Combining program
and data storage in one device saves board space and cost.
The DS5001FP offers several bank switches for access to even more memory. In addition to the primary
data area of 64kB, a peripheral selector creates a second 64kB data space with four accompanying chip
enables. This area can be used for memory-mapped peripherals or more data storage. The DS5001FP can
also use its expanded bus on ports 0 and 2 (like an 8051) to access an additional 64kB of data space.
Lastly, the DS5001FP provides one additional bank switch that changes up to 60kB of the NV RAM
program space into data memory. Thus, with a small amount of logic, the DS5001 accesses up to 252kB
of data memory.
The DS2251T is available (Refer to the data sheet at /microcontrollers.) for users
who want a preconstructed module using the DS5001FP, RAM, lithium cell, and a real-time clock. For
more details, refer to the Secure Microcontroller User’s Guide. For users desiring software security, the
DS5002FP is functionally identical to the DS5001FP but provides superior firmware security. The 44-pin
DS5001FP
Figure 1. BLOCK DIAGRAM

PIN DESCRIPTION
PIN
80 PIN 44 PIN NAME FUNCTION

11, 9, 7,
5, 1, 79,
77, 75
31
(P0.5)
P0.0–
P0.7
General-Purpose I/O Port 0. This port is open-drain and cannot drive a logic 1. It

requires external pullups. Port 0 is also the multiplexed expanded address/data bus.
When used in this mode, it does not require pullups.
15, 17,
19, 21,
25, 27,
29, 31
44
(P1.3)
P1.0–
P1.7 General-Purpose I/O Port 1

49, 50,
51, 56,
58, 60,
64, 66 P2.0–
P2.7
General-Purpose I/O Port 2. Also serves as the MSB of the address in expanded

memory accesses, and as pins of the RPC mode when used.
36 8 P3.0/RX
General-Purpose I/O Port Pin 3.0. Also serves as the receive signal for the on

board UART. This pin should not be connected directly to a PC COM port.
38 10 P3.1/TX
General-Purpose I/O Port Pin 3.1. Also serves as the transmit signal for the on

board UART. This pin should not be connected directly to a PC COM port.
39 — P3.2/
INT0
General-Purpose I/O Port Pin 3.2. Also serves as the active-low external interrupt

0.
40 11 P3.3/
INT1
General-Purpose I/O Port Pin 3.3. Also serves as the active-low external interrupt

1.
41 — P3.4/T0 General-Purpose I/O Port Pin 3.4. Also serves as the timer 0 input.
44 12 P3.5/T1 General-Purpose I/O Port Pin 3.5. Also serves as the timer 1 input.
45 13 P3.6/WR General-Purpose I/O Port Pin. Also serves as the write strobe for expanded bus
operation.
46 — P3.7/RD General-Purpose I/O Port Pin. Also serves as the read strobe for expanded bus
operation.
68 25 PSEN
Program Store Enable. This active-low signal is used to enable an external

program memory when using the expanded bus. It is normally an output and should
be unconnected if not used. PSEN also is used to invoke the bootstrap loader. At this
time, PSEN is pulled down externally. This should only be done once the DS5001FP
is already in a reset state. The device that pulls down should be open drain since it
must not interfere with PSEN under normal operation.
34 6 RST
Active-High Reset Input. A logic 1 applied to this pin will activate a reset state.

This pin is pulled down internally so this pin can be left unconnected if not used. An
RC power-on reset circuit is not needed and is not recommended.
70 27 ALE
Address Latch Enable. Used to demultiplex the multiplexed expanded address/data

bus on port 0. This pin is normally connected to the clock input on a ’373 type
transparent latch.
47, 48 14, 15 XTAL2,
XTAL1
Crystal Connections. Used to connect an external crystal to the internal oscillator.

XTAL1 is the input to an inverting amplifier and XTAL2 is the output.
52 16 GND Logic Ground
13 39 VCC Power Supply, +5V
12 38 VCCO
VCC Output. This is switched between VCC and VLI by internal circuits based on the

level of VCC. When power is above the lithium input, power will be drawn from VCC.
The lithium cell remains isolated from a load. When VCC is below VLI, the VCCO
switches to the VLI source. VCCO should be connected to the VCC pin of an SRAM.
PIN DESCRIPTION (continued)
PIN
80 PIN 44 PIN NAME FUNCTION

53, 16,
8, 18,
80, 76,
4, 6, 20,
24, 26,
28, 30,
33, 35,
37
41, 36,
42, 32,
30, 34,
35, 43,
1, 2, 3,
4, 5, 7,
BA14–
BA0
Byte-Wide Address Bus Bits 14–0. This bus is combined with the nonmultiplexed

data bus (BD7–0) to access NV SRAM. Decoding is performed using CE1 through
CE4. Therefore, BA15 is not actually needed. Read/write access is controlled by W. BA14–0 connect directly to an 8k, 32k, or 128k SRAM. If an 8k RAM is
used, BA13 and BA14 are unconnected. If a 128k SRAM is used, the micro converts
CE2 and CE3 to serve as A16 and A15 respectively.
71, 69,
67, 65,
61, 59,
57, 55
28, 26,
24, 23,
21, 20,
19, 18
BD7–0
Byte-Wide Data Bus Bits 7–0. This 8-bit, bidirectional bus is combined with the

nonmultiplexed address bus (BA14–0) to access NV SRAM. Decoding is performed
on CE1 and CE2. Read/write access is controlled by R/W. BD7–0 connect directly to
an SRAM, and optionally to a real-time clock or other peripheral.
10 37 R/W
Read/Write. This signal provides the write enable to the SRAMs on the byte-wide

bus. It is controlled by the memory map and partition. The blocks selected as
program (ROM) are write-protected.
74 29 CE1
Chip Enable 1. This is the primary decoded chip enable for memory access on the

byte-wide bus. It connects to the chip enable input of one SRAM. CE1 is lithium-
backed. It remains in a logic high inactive state when VCC falls below VLI.
72 — CE1N Non-Battery-Backed Version of Chip Enable 1. This can be used with a 32kB
EPROM. It should not be used with a battery-backed chip.
2 33 CE2
Chip Enable 2. This chip enable is provided to access a second 32k block of

memory. It connects to the chip enable input of one SRAM. When MSEL = 0, the
micro converts CE2 into A16 for a 128k x 8 SRAM. CE2 is lithium-backed and
remains at a logic high when VCC falls below VLI.
63 22 CE3
Chip Enable 3. This chip enable is provided to access a third 32k block of memory.

It connects to the chip enable input of one SRAM. When MSEL = 0, the micro
converts CE3 into A15 for a 128k x 8 SRAM. CE3 is lithium-backed and remains at
a logic high when VCC falls below VLI.
62 — CE4
Chip Enable 4. This chip enable is provided to access a fourth 32k block of

memory. It connects to the chip-enable input of one SRAM. When MSEL = 0, this
signal is unused. CE4 is lithium-backed and remains at a logic high when VCC < VLI.
78 — PE1
Peripheral Enable 1. Accesses data memory between addresses 0000h and 3FFFh

when the PES bit is set to a logic 1. Commonly used to chip enable a byte-wide real-
time clock such as the DS1283. PE1 is lithium-backed and remains at a logic high
when VCC falls below VLI. Connect PE1 to battery-backed functions only.
3 — PE2
Peripheral Enable 2. Accesses data memory between addresses 4000h and 7FFFh

when the PES bit is set to a logic 1. PE2 is lithium-backed and remains at a logic
high when VCC falls below VLI. Connect PE2 to battery-backed functions only.
22 — PE3
Peripheral Enable 3. Accesses data memory between addresses 8000h and BFFFh

when the PES bit is set to a logic 1. PE3 is not lithium-backed and can be connected
to any type of peripheral function. If connected to a battery-backed chip, it needs
additional circuitry to maintain the chip enable in an inactive state when VCC < VLI.
23 — PE4
Peripheral Enable 4. Accesses data memory between addresses C000h and FFFFh

when the PES bit is set to a logic 1. PE4 is not lithium-backed and can be connected
to any type of peripheral function. If connected to a battery-backed chip, it needs
additional circuitry to maintain the chip enable in an inactive state when VCC < VLI.
32 — PROG
Invokes the bootstrap loader on a falling edge. This signal should be debounced

so that only one edge is detected. If connected to ground, the micro enters bootstrap
DS5001FP
PIN DESCRIPTION (continued)
PIN
80 PIN 44 PIN NAME FUNCTION

42 — VRST
This I/O pin (open drain with internal pullup) indicates that the power supply
(VCC) has fallen below the VCCmin level and the micro is in a reset state. When

this occurs, the DS5001FP drives this pin to a logic 0. Because the micro is lithium-
backed, this signal is guaranteed even when VCC = 0V. Because it is an I/O pin, it
also forces a reset if pulled low externally. This allows multiple parts to synchronize
their power-down resets.
43 — PF
This output goes to a logic 0 to indicate that VCC < VLI and the micro has
switched to lithium backup. Because the micro is lithium-backed, this signal is

guaranteed even when VCC = 0V. The normal application of this signal is to control
lithium-powered current to isolate battery-backed functions from non-battery-backed
functions.
14 40 MSEL
Memory Select. This signal controls the memory size selection. When MSEL =

+5V, the DS5001FP expects to use 32k x 8 SRAMs. When MSEL = 0V, the
DS5001FP expects to use a 128k x 8 SRAM. MSEL must be connected regardless of
partition, mode, etc.
73 — N.C. No Connection
INSTRUCTION SET

The DS5001FP executes an instruction set that is object code-compatible with the industry standard 8051
microcontroller. As a result, software development packages such as assemblers and compilers that have
been written for the 8051 are compatible with the DS5001FP. A complete description of the instruction
set and operation are provided in the Secure Microcontroller User’s Guide. Also note that the DS5001FP
is embodied in the DS2251T module. The DS2251T combines the DS5001FP with between 32k and 128k
of SRAM, a lithium cell, and a real-time clock. This is packaged in a 72-pin SIMM module.
MEMORY ORGANIZATION

Figure 2 illustrates the memory map accessed by the DS5001FP. The entire 64k of program and 64k of
data are potentially available to the byte-wide bus. This preserves the I/O ports for application use. The
user controls the portion of memory that is actually mapped to the byte-wide bus by selecting the program
range and data range. Any area not mapped into the NV RAM is reached by the expanded bus on ports 0
and 2. An alternate configuration allows dynamic partitioning of a 64k space as shown in Figure 3.
Selecting PES=1 provides another 64k of potential data storage or memory-mapped peripheral space as
shown in Figure 4. These selections are made using special function registers. The memory map and its
controls are covered in detail in the Secure Microcontroller User’s Guide.
DS5001FP
Figure 2. MEMORY MAP IN NONPARTITIONABLE MODE (PM = 1)

DS5001FP
Figure 3. MEMORY MAP IN PARTITIONABLE MODE (PM = 0) NOTE: PARTITIONABLE MODE IS NOT SUPPORTED WHEN MSEL PIN = 0 (128kB MODE).
DS5001FP
Figure 4. MEMORY MAP WITH PES = 1

DS5001FP
Figure 5 illustrates a typical memory connection for a system using a 128kB SRAM. Note that in this
configuration, both program and data are stored in a common RAM chip Figure 6 shows a similar system
with using two 32kB SRAMs. The byte-wide address bus connects to the SRAM address lines. The
bidirectional byte-wide data bus connects the data I/O lines of the SRAM.
Figure 5. CONNECTION TO 128k x 8 SRAM

DS5001FP
Figure 6. DS5001FP CONNECTION TO 64k x 8 SRAM

POWER MANAGEMENT

The DS5001FP monitors VCC to provide power-fail reset, early warning power-fail interrupt, and switch
over to lithium backup. It uses an internal bandgap reference in determining the switch points. These are
called VPFW, VCCMIN, and VLI, respectively. When VCC drops below VPFW, the DS5001FP performs an
interrupt vector to location 2Bh if the power-fail warning was enabled. Full processor operation continues
regardless. When power falls further to VCCMIN, the DS5001FP invokes a reset state. No further code
execution is performed unless power rises back above VCCMIN. All decoded chip enables and the R/W
signal go to an inactive (logic 1) state. VCC is still the power source at this time. When VCC drops further
to below VLI, internal circuitry switches to the lithium cell for power. The majority of internal circuits are
disabled and the remaining nonvolatile states are retained. Any devices connected VCCO are powered by
the lithium cell at this time. VCCO is at the lithium battery voltage minus approximately 0.45V. This drop
varies depending on the load. Low power SRAMs should be used for this reason. When using the
DS5001FP, the user must select the appropriate battery to match the RAM data retention current and the
desired backup lifetime. Note that the lithium cell is only loaded when VCC < VLI. The User’s Guide has
more information on this topic. The trip points VCCMIN and VPFW are listed in the Electrical Specifications
DS5001FP
ABSOLUTE MAXIMUM RATINGS

Voltage Range on Any Pin Relative to Ground…………………………..…………………….-0.3V to (VCC + 0.5V)
Voltage Range on VCC Related to Ground………………………………………………………………-0.3V to 6.0V
Operating Temperature Range………………………………………………………………………...-40C to +85C
Storage Temperature Range (Note 1)………………………………………………………………..-55C to +125C
Soldering Temperature…………………………………………………….See IPC/JEDEC J-STD-020 Specification
This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operation
sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods of time may affect reliability.
Note 1: Storage temperature is defined as the temperature of the device when VCC = 0V and VLI = 0V. In

this state, the contents of SRAM are not battery-backed and are undefined.
DC CHARACTERISTICS

(VCC = 5V ±10%, TA = 0°C to +70°C.)
PARAMETER SYMBOL MIN TYP MAX UNITS NOTES

Input Low Voltage VIL -0.3 +0.8 V 1
Input High Voltage VIH1 2.0 VCC + 0.3 V 1
Input High Voltage
(RST, XTAL1, PROG) VIH2 3.5 VCC + 0.3 V 1
Output Low Voltage
at IOL = 1.6mA (Ports 1, 2, 3, PF) VOL1 0.15 0.45 V 1, 11
Output Low Voltage
at IOL = 3.2mA (Ports 0, ALE, PSEN,
BA15–0, BD7–0, R/W, CE1N, 1–4, PE1–4, VRST)
VOL2 0.15 0.45 V 1
Output High Voltage
at IOH = -80µA (Ports 1, 2, 3) VOH1 2.4 4.8 V 1
Output High Voltage
at IOH = -400µA (Ports 0, ALE, PSEN, , BA15–0, BD7–0, R/W, CE1N, 1–4, PE1–4, VRST)
VOH2 2.4 4.8 V 1
Input Low Current
VIN = 0.45V (Ports 1, 2, 3) IIL -50 µA
Transition Current; 1 to 0
VIN = 2.0V (Ports 1, 2, 3)
(0°C to +70°C)
ITL -500 µA
Transition Current; 1 to 0
VIN = 2.0V (Ports 1, 2, 3)
(-40°C to +85°C)
ITL -600 µA 10
DS5001FP
DC CHARACTERISTICS (continued)

(VCC = 5V ±10%, TA = 0°C to +70°C.)
PARAMETER SYMBOL MIN TYP MAX UNITS NOTES

Input Leakage Current
0.45 < VIN < VCC (Port 0, MSEL) IIL +10 µA
RST Pulldown Resistor
(0°C to +70°C) RRE 40 150 k
RST Pulldown Resistor
(-40°C to +85°C) RRE 30 180 k 10
VRST Pullup Resistor RVR 4.7 k
PROG Pullup Resistor RPR 40 k
Power-Fail Warning Voltage
(0°C to +70°C) VPFW 4.25 4.37 4.50 V 1
Power-Fail Warning Voltage
(-40°C to +85°C) VPFW 4.1 4.37 4.6 V 1, 10
Minimum Operating Voltage
(0°C to +70°C) VCCMIN 4.00 4.12 4.25 V 1
Minimum Operating Voltage
(-40°C to +85°C) VCCMIN 3.85 4.09 4.25 V 1, 10
Operating Voltage VCC VCCMIN 5.5 V 1
Lithium Supply Voltage VLI 2.5 4.0 V 1
Operating Current at 16MHz ICC 36 mA 2
Idle Mode Current at 12MHz
(0°C to +70°C) IIDLE 7.0 mA 3
Idle Mode Current at 12MHz
(-40°C to +85°C) IIDLE 8.0 mA 3, 10
Stop Mode Current ISTOP 80 µA 4
Pin Capacitance CIN 10 pF 5
Output Supply Voltage (VCCO) VCCO1 VCC
-0.45 V 1, 2
Output Supply Battery-Backed Mode
(VCCO, CE1-4, PE1-2)
(0°C to +70°C)
VCCO2 VLI
-0.65 V 1, 8
Output Supply Battery-Backed Mode
(VCCO, CE1-4, PE1-2)
(-40°C to +85°C)
VCCO2 VLI
-0.9 V 1, 8, 10
Output Supply Current
at VCCO = VCC - 0.45V ICCO1 75 mA 6
Lithium-Backed Quiescent Current
(0°C to +70°C) ILI 5 75 nA 7
Lithium-Backed Quiescent Current
(-40°C to +85°C) ILI 75 500 nA 7
With BAT = 3.0V
(0°C to +70°C) 4.0 4.25 1
With BAT = 3.0V
(-40°C to +85°C) 3.85 4.25 1, 10 Reset Trip Point
in Stop Mode
With BAT = 3.0V
(0°C to +70°C) 4.4 4.65 1
DS5001FP
AC CHARACTERISTICS: EXPANDED BUS MODE TIMING SPECIFICATIONS

(VCC = 5V ±10%, TA = 0°C to +70°C.)
# PARAMETER SYMBOL MIN MAX UNITS
Oscillator Frequency 1/ tCLK 1.0 16 MHz
2 ALE Pulse Width tALPW 2tCLK - 40 ns Address Valid to ALE Low tAVALL tCLK - 40 ns Address Hold After ALE Low tAVAAV tCLK - 35 ns
at 12MHz 4tCLK - 150 5 ALE Low to Valid Instruction In
at 16MHz tALLVI 4tCLK - 90 ns ALE Low to PSEN Low tALLPSL tCLK - 25 ns PSEN Pulse Width tPSPW 3tCLK - 35 ns
at 12MHz 3tCLK - 150 8 PSEN Low to Valid Instruction
In at 16MHz tPSLVI 3tCLK - 90 ns Input Instruction Hold After PSEN Going High tPSIV 0 ns
10 Input Instruction Float After PSEN Going High tPSIX tCLK - 20 ns
11 Address Hold After PSEN Going High tPSAV tCLK - 8 ns
at 12MHz 5tCLK - 150 12 Address Valid to Valid
Instruction In at 16MHz tAVVI 5tCLK - 90 ns
13 PSEN Low to Address Float tPSLAZ 0 ns
14 RD Pulse Width tRDPW 6tCLK - 100 ns
15 WR Pulse Width tWRPW 6tCLK - 100 ns
at 12MHz 5tCLK - 165 16 RD Low to Valid Data In at 16MHz tRDLDV 5tCLK - 105 ns
17 Data Hold After RD High tRDHDV 0 ns
18 Data Float After RD High tRDHDZ 2tCLK - 70 ns
at 12MHz 8tCLK - 150 19 ALE Low to Valid Data In at 16MHz tALLVD 8tCLK - 90 ns
at 12MHz 9tCLK - 165 20 Valid Address to Valid Data In at 16MHz tAVDV 9tCLK - 105 ns
21 ALE Low to RD or WR Low tALLRDL 3tCLK - 50 3tCLK + 50 ns
22 Address Valid to RD or WR Low tAVRDL 4tCLK - 130 ns
23 Data Valid to WR Going Low tDVWRL tCLK - 60 ns
at 12MHz 7tCLK - 150 24 Data Valid to WR High at 16MHz tDVWRH 7tCLK - 90 ns
25 Data Valid After WR High tWRHDV tCLK - 50 ns
26 RD Low to Address Float tRDLAZ 0 ns
27 RD or WR High to ALE High tRDHALH tCLK - 40 tCLK + 50 ns
ic,good price


TEL:86-533-2716050      FAX:86-533-2716790
   

©2020 IC PHOENIX CO.,LIMITED