IC Phoenix
 
Home ›  DD28 > DS2108S,Differential SCSI Switchable Terminator
DS2108S Fast Delivery,Good Price
Part Number:
If you need More Quantity or Better Price,Welcom Any inquiry.
We available via phone +865332716050 Email
Partno Mfg Dc Qty AvailableDescript
DS2108SDALLASN/a5747avaiDifferential SCSI Switchable Terminator


DS2108S ,Differential SCSI Switchable TerminatorFUNCTIONAL DESCRIPTIONThe DS2108 consists of power-down circuitry, eighteen 330-ohm and nine 150-oh ..
DS2108S/T&R ,Differential SCSI Switchable TerminatorFEATURES PIN ASSIGNMENT Fully compliant with SCSI, SCSI-2 and SCSI-3 standards1 24TPWR PD Conform ..
DS2109 ,Plug and Play SCSI TerminatorFUNCTIONAL DESCRIPTIONSCSI–2 (X3.131–1994) The DS2109 is designed to be a single chip terminationSC ..
DS2117M ,Ultra2 LVD/SE SCSI TerminatorFUNCTIONAL DESCRIPTIONThe DS2117 combines LVD and SE termination with DIFFSENSE sourcing and detect ..
DS2118M ,Ultra3 LVD/SE SCSI TerminatorFEATURES PIN CONFIGURATION Fully Compliant with SCSI SPI-2, SPI-3, SPI-4, Ultra160, and Ultra32 ..
DS2118MB ,Ultra2 LVD/SE SCSI TerminatorFEATURES PIN CONFIGURATION Fully Compliant with SCSI SPI-2, SPI-3, SPI-4, Ultra160, and Ultra32 ..


DS2108S
Differential SCSI Switchable Terminator
FEATURESFully compliant with SCSI, SCSI-2 and SCSI-
3 standardsConforms to EIA RS-485 standardProvides differential termination for 9 pairs of
signal linesOperates with SCSI signal voltages of -7 to
+12 VoltsLaser-trimmed 330 and 150-ohm terminationresistors have ±5% tolerance over full
temperature rangeSwitchable power-down modeLow power down capacitance of 6 pF24-pin plastic SOIC (DS2108S)
PIN ASSIGNMENT
DESCRIPTION

The DS2108 SCSI Terminator has been specifically designed for High Voltage Differential (HVD) SCSI
systems requiring switchable termination. The DS2108 integrates eighteen 330-ohm and nine 150-ohm
precise switched termination resistors into a monolithic IC. The surface mount SOIC package saves boardspace over conventional resistor SIPs. The termination resistors can be isolated from the SCSI bus under
software or hardware control. While in the powered down mode, the DS2108 isolates the nine terminator
blocks from the bus while adding only 6 pF capacitance to each signal line of the SCSI bus.
FUNCTIONAL DESCRIPTION

The DS2108 consists of power-down circuitry, eighteen 330-ohm and nine 150-ohm termination resistors
(Figure 1). The DS2108 can be removed from the circuit by bringing the power down pin (PD) low. Thepower down capacitance on the terminating resistors is 6 pF, well below the SCSI-3 allotment of 25 pF.
The DS2108 supports SCSI signal voltages of -7 to +12 volts when powered on or off. When all lines
settle into the quiescent state (no signal transitions), 56 mA is typically consumed. Only 1 mA is
typically consumed in the powered down mode.
DS2108
Differential SCSI Switchable Terminator

GND
R1P
R3P
R4P
R5P
R6P
R7P
R8P
R9P
GND
R2P
TPWR
R1N
R2N
R4N
R5N
R6N
R7N
R8N
R9N
TPWR
R3N
DS2108
DS2108 BLOCK DIAGRAM Figure 1
DS2108
TYPICAL DIFFERENTIAL SCSI BUS CONFIGURATION Figure 2
NOTES:

1. Two DS2108s required per 8–bit SCSI device and three DS2108s per 16–bit SCSI device.
2. Mid–bus termination effectively removed by grounding PD pin.
3. Termination power to be provided as specified in SCSI–3 Parallel Interface (SPI) document.
4. Local TERMPWR bypassing is recommended by the SPI document with values shown. The bypass
capacitors should be located as close as possible to the DS2108s. Only one pair of capacitors is
required per SCSI device (may be shared between DS2108s on same device).
PIN DESCRIPTION Table 1
DS2108
ABSOLUTE MAXIMUM RATINGS*

Voltage on Any Pin Relative to Ground-7.0V to +12.0V
Operating Temperature0°C to 70°C
Storage Temperature-55°C to +125°C
Soldering Temperature260°C for 10 seconds
* This is a stress rating only and functional operation of the device at these or any other conditions above
those indicated in the operation sections of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods of time may affect reliability.
RECOMMENDED OPERATING CONDITIONS
(0°C to 70°C)
DC CHARACTERISTICS
NOTES:

1. 4.00V < TERMPWR < 5.25V
2. 330 Ω=resistor between TERMPWR and -SIGNAL.
3. 150 Ω=resistor between -SIGNAL and +SIGNAL.
4. 330 Ω=resistor between +SIGNAL and GDN.
5. PD = 0.0V.
6. Signal pins left open.
7. Guaranteed by design; not production tested.
8. Signal lines RxN and RxP only.
DS2108
24-PIN SOIC (300-MIL)

The chamfer on the body is optional. If it is not present, a terminal 1 identifier must be positioned so that
½ or more of its area is contained in the hatched zone.
This datasheet has been :
www.ic-phoenix.com
Datasheets for electronic components.
ic,good price


TEL:86-533-2716050      FAX:86-533-2716790
   

©2020 IC PHOENIX CO.,LIMITED