IC Phoenix
 
Home ›  DD27 > DS1992L-F5+-DS1993L-F5+,iButton 1Kb/4Kb Memory
DS1992L-F5+-DS1993L-F5+ Fast Delivery,Good Price
Part Number:
If you need More Quantity or Better Price,Welcom Any inquiry.
We available via phone +865332716050 Email
Partno Mfg Dc Qty AvailableDescript
DS1992L-F5+ |DS1992LF5+MAIXMN/a3000avaiiButton 1Kb/4Kb Memory
DS1993L-F5+ |DS1993LF5+MAIXMN/a3000avaiiButton 1Kb/4Kb Memory


DS1992L-F5+ ,iButton 1Kb/4Kb MemoryFEATURES  4096 bits of Read/Write Nonvolatile  Unique, Factory-Lasered and Tested 64-bit Memory ( ..
DS1993L-F5 ,1kbit/4kbit Memory iButtonTM DS1994 4-kbit Plus Time Memory iButtonTMFEATURESYYWW REGISTERED RR Unique, Factory-Lasered and Tested 64-bit06DD17.35Registration Num ..
DS1993L-F5+ ,iButton 1Kb/4Kb Memoryblock diagram (Figure 1) shows the parasite-powered circuitry. This circuitry steals power whenever ..
DS1994L-F5 ,4kb plus time memory iButtonblock diagram (Figure 1) shows the parasite-powered circuitry. This circuitry steals power whenever ..
DS1994L-F5+ ,iButton 4Kb Memory Plus TimeFEATURES  4096 bits of Read/Write Nonvolatile Memory  Unique, Factory-Lasered, and Tested 64-bit ..
DS1995L-F5 ,16-kbit Memory iButtonDS1995TM16-kbit Memory iButtonwww.dalsemi.com§ Meets UL#913 (4th Edit.); Intrinsically SafeSPECIAL


DS1992L-F5+-DS1993L-F5+
iButton 1Kb/4Kb Memory
SPECIAL FEATURES  4096 bits of Read/Write Nonvolatile
Memory (DS1993)  1024 bits of Read/Write Nonvolatile
Memory (DS1992)  256-bit Scratchpad Ensures Integrity of Data
Transfer  Memory Partitioned into 256-bit Pages for
Packetizing Data  Data Integrity Assured with Strict
Read/Write Protocols  Operating Temperature Range from -40°C to
+70°C  Over 10 years of data retention
ORDERING INFORMATION

DS1992L-F5+ F5 MicroCan
DS1993L-F5+ F5 MicroCan
+Denotes a lead(Pb)-free/RoHS-compliant product.
EXAMPLES OF ACCESSORIES

DS9096P Self-Stick Adhesive Pad
DS9101 Multipurpose Clip
DS9093RA Mounting Lock Ring
DS9093F Snap-In Fob
DS9092 iButton Probe
F5 MicroCan

COMMON iButton FEATURES
 Unique, Factory-Lasered and Tested 64-bit
Registration Number (8-bit Family Code +
48-bit Serial Number + 8-bit CRC Tester)
Assures Absolute Traceability Because No
Two Parts are Alike  Multidrop Controller for MicroLAN  Digital Identification and Information by
Momentary Contact  Chip-Based Data Carrier Compactly Stores
Information  Data Can be Accessed While Affixed to
Object  Economically Communicates to Bus Master
with a Single Digital Signal at 16.3kbps  Standard 16mm Diameter and 1-Wire®
Protocol Ensure Compatibility with iButton®
Family  Button Shape is Self-Aligning with Cup-
Shaped Probes  Durable Stainless Steel Case Engraved with
Registration Number Withstands Harsh
Environments  Easily Affixed with Self-Stick Adhesive
Backing, Latched by its Flange, or Locked
with a Ring Pressed onto its Rim  Presence Detector Acknowledges When
Reader First Applies Voltage  Meets UL 913, 5th Ed., Rev. 1997-02-24;
Intrinsically Safe Apparatus, Approved under
Entity Concept for use in Class I, Division 1,
Group A, B, C, and D Locations
DS1992/DS1993
1Kb/4Kb Memory iButton

1-Wire and iButton are registered trademarks of Maxim Integrated Products, Inc.
19-4865; Rev 4/11
DS1992/DS1993
iButton DESCRIPTION

The DS1992/DS1993 memory iButtons (hereafter referred to as DS199x) are rugged read/write data
carriers that act as a localized database, easily accessible with minimal hardware. The nonvolatile
memory and optional timekeeping capability offer a simple solution to storing and retrieving vital
information pertaining to the object to which the iButton is attached. Data is transferred serially through
the 1-Wire protocol that requires only a single data lead and a ground return.
The scratchpad is an additional page that acts as a buffer when writing to memory. Data is first written to
the scratchpad where it can be read back. After the data has been verified, a copy scratchpad command
transfers the data to memory. This process ensures data integrity when modifying the memory. A 48-bit
serial number is factory lasered into each DS199x to provide a guaranteed unique identity that allows for
absolute traceability. The durable MicroCan package is highly resistant to environmental hazards such as
dirt, moisture, and shock. Its compact coin-shaped profile is self-aligning with mating receptacles,
allowing the DS199x to be easily used by human operators. Accessories permit the DS199x to be
mounted on almost any surface including plastic key fobs, photo-ID badges, and PC boards.
Applications include access control, work-in-progress tracking, electronic travelers, storage of calibration
constants, and debit tokens.
OPERATION

The DS199x have three main data components: 1) 64-bit lasered ROM, 2) 256-bit scratchpad, and 3)
1024-bit (DS1992) or 4096-bit (DS1993) SRAM. All data is read and written least significant bit first.
The memory functions are not available until the ROM function protocol has been established. This
protocol is described in the ROM functions flow chart (Figure 9). The master must first provide one of
four ROM function commands: 1) read ROM, 2) match ROM, 3) search ROM, or 4) skip ROM. After a
ROM function sequence has been successfully executed, the memory functions are accessible and the
master can then provide any one of the four memory function commands (Figure 6).
PARASITE POWER

The block diagram (Figure 1) shows the parasite-powered circuitry. This circuitry steals power whenever
the data input is high. The data line provides sufficient power as long as the specified timing and voltage
requirements are met. The advantages of parasite power are two-fold: 1) by parasiting off this input,
battery power is not consumed for 1-Wire ROM function commands, and 2) if the battery is exhausted for
any reason, the ROM may still be read normally. The remaining circuitry of the DS1992 and DS1993 is
solely operated by battery energy.
64-BIT LASERED ROM

Each DS199x contain a unique ROM code that is 64 bits long. The first 8 bits are a 1-Wire family code.
The next 48 bits are a unique serial number. The last 8 bits are a CRC of the first 56 bits (see Figure 2).
The 1-Wire CRC is generated using a polynomial generator consisting of a shift register and XOR gates
as shown in Figure 3. The polynomial is X8 + X5 + X4 + 1. Additional information about the Maxim
1-Wire Cyclic Redundancy Check is available in the Book of DS19xx iButton Standards. The shift
register bits are initialized to zero. Then starting with the least significant bit of the family code, 1 bit at a
time is shifted in. After the 8th bit of the family code has been entered, then the serial number is entered.
After the 48th bit of the serial number has been entered, the shift register contains the CRC value.
Shifting in the 8 bits of CRC should return the shift register to all zeros.
DS1992/DS1993
Figure 1. DS1992/DS1993 BLOCK DIAGRAM

SRAM
16 PAGES of 256-
BITs (1993)
256-BIT
SCRATCHPAD
1-W
ROM
CONTROL
FUNCTION64-BIT
ROM
LASERED
PARASITE-
CIRCUITRY
POWERED
MEMORY
FUNCTION
CONTROL
1-WIRE
PORT
3V LITHIUM
4 PAGES of 256-
BITs (1992)Figure 2. 64-BIT LASERED ROM
MSB LSB

8-Bit CRC Code

48-Bit Serial Number
8-Bit Family Code
(06h)1993
(08h)1992
MSB LSB MSB LSB MSB LSB
Figure 3. 1-Wire CRC CODE
0X1X2X3X4X5X6X7X8
Polynomial = X8 + X5 + X4 + 1st
STAGEnd
STAGErd
STAGEth
STAGEth
STAGEth
STAGEth
STAGEth
STAGE
INPUT DATA
DS1992/DS1993
Figure 4a. DS1993 MEMORY MAP

PAGE 0
PAGE
PAGE 1
PAGE 2
PAGE 3
PAGE 4
PAGE 5
PAGE 6
PAGE 7
PAGE 8
PAGE 9
PAGE 10
PAGE 11
PAGE 12
PAGE 13
PAGE 14
PAGE 15
SCRATCHPAD
MEMORY
0000h
0020h
0040h
0060h
0080h
00A0h
00C0h
00E0h
0100h
0120h
0140h
0160h
0180h
01A0h
01C0h
01E0h
NOTE: Each page is 32 bytes (256 bits). The hex values
represent the starting address for each page or register.
Figure 4b. DS1992 MEMORY MAP

PAGE 0
PAGE
PAGE 1
PAGE 2
PAGE 3
SCRATCHPAD
MEMORY
0000h
0020h
0040h
0060h
NOTE: Each page is 32 bytes (256 bits). The hex values
represent the starting address for each page or register.
DS1992/DS1993
MEMORY

The memory map in Figure 4 shows a 32-Byte page called the scratchpad, and additional 32-Byte pages
called memory. The DS1992 contains pages 0 though 3 that make up the 1024-bit SRAM. The DS1993
contain pages 0 through 15 that make up the 4096-bit SRAM.
The scratchpad is an additional page that acts as a buffer when writing to memory. Data is first written to
the scratchpad where it can be read back. After the data has been verified, a copy scratchpad command
transfers the data to memory. This process ensures data integrity when modifying the memory.
MEMORY FUNCTION COMMANDS

The Memory Function Flow Chart (Figure 6) describes the protocols necessary for accessing the memory.
An example follows the flow chart. Three address registers are provided as shown in Figure 5. The first
two registers represent a 16-bit target address (TA1, TA2). The third register is the ending offset/data
status byte (E/S).
The target address points to a unique Byte location in memory. The first 5 bits of the target address
(T4:T0) represent the Byte offset within a page. This Byte offset points to one of 32 possible Byte
locations within a given page. For instance, 00000b points to the first Byte of a page where as 11111b
would point to the last Byte of a page.
The third register (E/S) is a read only register. The first 5 bits (E4: E0) of this register are called the
ending offset. The ending offset is a Byte offset within a page (1 of 32 Bytes). Bit 5 (PF) is the partial
Byte flag. Bit 6 (OF) is the overflow flag. Bit 7 (AA) is the authorization accepted flag.
Figure 5. ADDRESS REGISTERS
7 6 5 4 3 2 1 0
TARGET ADDRESS (TA1) T7 T6 T5 T4 T3 T2 T1 T0
TARGET ADDRESS (TA2) T15 T14 T13 T12 T11 T10 T9 T8
ENDING ADDRESS WITH
DATA STATUS (E/S)
(READ ONLY)
AA OF PF E4 E3 E2 E1 E0
Write Scratchpad Command [0Fh]

After issuing the write scratchpad command, the user must first provide the 2-Byte target address,
followed by the data to be written to the scratchpad. The data is written to the scratchpad starting at the
byte offset (T4:T0). The ending offset (E4:E0) is the Byte offset at which the host stops writing data. The
maximum ending offset is 11111b (31d). If the host attempts to write data past this maximum offset, the
overflow flag (OF) is set and the remaining data is ignored. If the user writes an incomplete Byte and an
overflow has not occurred, the partial Byte flag (PF) is set.
Read Scratchpad Command [AAh]

This command can be used to verify scratchpad data and target address. After issuing the read scratchpad
command, the user can begin reading. The first two Bytes are the target address. The next Byte is the
ending offset/data status Byte (E/S) followed by the scratchpad data beginning at the Byte offset (T4: T0).
DS1992/DS1993
Copy Scratchpad [55h]

This command is used to copy data from the scratchpad to memory. After issuing the copy scratchpad
command, the user must provide a 3-byte authorization pattern. This pattern must exactly match the data
contained in the three address registers (TA1, TA2, E/S, in that order). If the pattern matches, the AA
(Authorization Accepted) flag is set and the copy begins. A logic 0 is transmitted after the data has been
copied until the user issues a reset pulse. Any attempt to reset the part is ignored while the copy is in
progress. Copy typically takes 30µs.
The data to be copied is determined by the three address registers. The scratchpad data from the
beginning offset through the ending offset is copied to memory, starting at the target address. Anywhere
from 1 to 32 Bytes can be copied to memory with this command. Whole Bytes are copied even if only
partially written. The AA flag is cleared only by executing a write scratchpad command.
Read Memory [F0h]

The read memory command can be used to read the entire memory. After issuing the command, the user
must provide the 2-Byte target address. After the two Bytes, the user reads data beginning from the target
address and may continue until the end of memory, at which point logic 1’s are read. It is important to
realize that the target address registers contains the address provided. The ending offset/data status Byte
is unaffected.
The hardware of the DS199x provides a means to accomplish error-free writing to the memory section.
To safeguard reading data in the 1-Wire environment and to simultaneously speed up data transfers, it is
recommended to packetize data into data packets of the size of one memory page each. Such a packet
would typically store a 16-bit CRC with each page of data to ensure rapid, error-free data transfers that
eliminate having to read a page multiple times to determine if the received data is correct or not. (See
Application Note 114 for the recommended file structure to be used with the 1-Wire environment.)
DS1992/DS1993
Figure 6. MEMORY FUNCTIONS FLOW CHART
Master TX Memory
Function Command
DS199x sets Scratchpad
Offset = (T4:T0) and
Clears (PF, OF, AA)
DS199x sets (E4:E0)
= Scratchpad Offset
DS199x Increments
Scratchpad Offset
Bus Master TX
TA1 (T7:T0)
Bus Master TX
TA2 (T15:T8)
Master TX Data Byte
To Scratchpad Offset
Bus Master TX Reset 0FH Write
Scratchpad Bus Master TX Data
PF = 1
Bus Master
TX Reset
To Figure 6
Second Part
Bus Master RX
TA1 (T7:T0)
Bus Master RX
TA2 (T15:T8)
Master RX Ending
Offset with Data
Status (E/S)
DS199x Sets
Scratchpad
Offset=(T4:T0)
Bus Master
TX Reset DS199x Increments
Scratchpad Offset
Master RX Data
Byte From
Scratchpad Offset Scratch- pad Offset = 11111b
Scratchpad
AAH Read
Bus Master
RX "1"s
From Figure 6
Second Part
OF = 1
Scratch- pad Offset = 11111b
Partial
Byte Written
DS199x TX
Presence Pulse
(See Figure 9)
DS1992/DS1993
Figure 6. MEMORY FUNCTIONS FLOW CHART (continued)

Bus Master TX
TA1 (T7:T0)
Bus Master TX
TA2 (T15:T8)
Scratchpad
55H Copy
From Figure 6
First Part
Bus Master TX
E/S Byte
DS199x Copies Scratchpad Data
To Memory
Authorization Code Match
DS199x TX "1"s
DS199x TX "0"s
AA = 1
F0H
Read Memory N
To Figure 6
First Part Bus Master TX Reset
Bus Master TX Reset Y Y
Bus Master TX
TA1 (T7:T0)
Bus Master TX
TA2 (T15:T8)
DS199x sets Memory
Address = (T15:T0)
Master RX Data
Byte From Memory Address
Bus Master
TX Reset
Memory
DS199x
Address Counter
Increments
Bus Master
RX "1"s
Address
= 21Dh
DS1992/DS1993
MEMORY FUNCTION EXAMPLES

Example: Write two data Bytes to memory locations 0026h and 0027h (the seventh and eighth Bytes of
page 1). Read entire memory.
MASTER MODE DATA (LSB FIRST) COMMENTS

TX Reset Reset pulse (480µs to 960µs)
RX Presence Presence pulse
TX CCh Issue skip ROM command
TX 0Fh Issue write scratchpad command
TX 26h TA1, beginning offset = 6
TX 00h TA2, address = 0026h
TX <2 data Bytes> Write 2 Bytes of data to scratchpad
TX Reset Reset pulse
RX Presence Presence pulse
TX CCh Issue skip ROM command
TX Aah Issue read scratchpad command
RX 26h Read TA1, beginning offset = 6
RX 00h Read TA2, address = 0026h
RX 07h Read E/S, ending offset = 7, flags = 0
RX <2 data Bytes> Read scratchpad data and verify
TX Reset Reset pulse
RX Presence Presence pulse
TX CCh Issue skip ROM command
TX 55h Issue copy scratchpad command
TX 26h TA1
TA2 AUTHORIZATION CODE
E/S
TX 00h
TX 07h
TX Reset Reset pulse
RX Presence Presence pulse
TX CCh Issue skip ROM command
TX F0h Issue read memory command
TX 00h TA1, beginning offset = 6
TX 00h TA2, address = 0000h
RX <128 Bytes (DS1992)>
<512 Bytes (DS1993)> Read entire memory
TX Reset Reset pulse
RX Presence Presence pulse, done
ic,good price


TEL:86-533-2716050      FAX:86-533-2716790
   

©2020 IC PHOENIX CO.,LIMITED