IC Phoenix
 
Home ›  DD23 > DS1251W-120+-DS1251W-120IND+-DS1251WP-120-DS1251WP-120+-DS1251Y-70-DS1251Y-70+-DS1251YP-70+,4096K NV SRAM with Phantom Clock
DS1251W-120+-DS1251W-120IND+-DS1251WP-120-DS1251WP-120+-DS1251Y-70 Fast Delivery,Good Price
Part Number:
If you need More Quantity or Better Price,Welcom Any inquiry.
We available via phone +865332716050 Email
Partno Mfg Dc Qty AvailableDescript
DS1251W-120+ |DS1251W120MAXIMN/a10avai4096K NV SRAM with Phantom Clock
DS1251W-120+ |DS1251W120MAXIM/DALLASN/a10avai4096K NV SRAM with Phantom Clock
DS1251W-120IND+ |DS1251W120INDDALLASN/a2avai4096K NV SRAM with Phantom Clock
DS1251WP-120 |DS1251WP120DALLASN/a717avai4096K NV SRAM with Phantom Clock
DS1251WP-120+ |DS1251WP120DALLASN/a2avai4096K NV SRAM with Phantom Clock
DS1251Y-70 |DS1251Y70DALLASN/a30avai4096K NV SRAM with Phantom Clock
DS1251Y-70+ |DS1251Y70+DALLASN/a180avai4096K NV SRAM with Phantom Clock
DS1251YP-70+ |DS1251YP70MAXIM/DALLASN/a2avai4096K NV SRAM with Phantom Clock


DS1251WP-120 ,4096K NV SRAM with Phantom ClockFEATURES PIN CONFIGURATIONS  Real-Time Clock Keeps Track of Hundredths TOP VIEW Of Seconds, Minut ..
DS1251WP-120+ ,4096K NV SRAM with Phantom Clock19-6079; Rev 11/11 DS1251/DS1251P 4096K NV SRAM with Phantom Clock
DS1251Y-150 , 4096K NV SRAM with Phantom Clock
DS1251Y-70 ,4096K NV SRAM with Phantom ClockPIN DESCRIPTION PIN NAME FUNCTION EDIP PowerCap 1 1 RST Active-Low Reset Input. This pin has an int ..
DS1251Y-70+ ,4096K NV SRAM with Phantom ClockPIN DESCRIPTION PIN NAME FUNCTION EDIP PowerCap 1 1 RST Active-Low Reset Input. This pin has an int ..
DS1251YP-70+ ,4096K NV SRAM with Phantom ClockPIN DESCRIPTION PIN NAME FUNCTION EDIP PowerCap 1 1 RST Active-Low Reset Input. This pin has an int ..
DTC114EE ,Pre-biased TransistorsTransistor) contains a single transistor with a monolithic bias networkconsisting of two resistors; ..
DTC114EET1 ,Bias Resistor TransistorMAXIMUM RATINGS (T = 25°C unless otherwise noted)ASC−75/SOT−416CASE 463xx MRating Symbol Value Un ..
DTC114EET1G ,Bias Resistor TransistorELECTRICAL CHARACTERISTICS (T = 25°C unless otherwise noted)ACharacteristic Symbol Min Typ Max Unit ..
DTC114EET1G ,Bias Resistor TransistorDTC114EET1 SeriesBias Resistor TransistorNPN Silicon Surface Mount Transistorwith Monolithic Bias R ..
DTC114EKA T146 , NPN 100mA 50V Digital Transistors
DTC114EKA T146 , NPN 100mA 50V Digital Transistors


DS1251W-120+-DS1251W-120IND+-DS1251WP-120-DS1251WP-120+-DS1251Y-70-DS1251Y-70+-DS1251YP-70+
4096K NV SRAM with Phantom Clock
FEATURES  Real-Time Clock Keeps Track of Hundredths
Of Seconds, Minutes, Hours, Days, Date of
the Month, Months, and Years  512K x 8 NV SRAM Directly Replaces
Volatile Static RAM or EEPROM  Embedded Lithium Energy Cell Maintains
Calendar Operation and Retains RAM Data  Watch Function is Transparent to RAM
Operation  Automatic Leap Year Compensation Valid
Up to 2100  Over 10 Years of Data Retention in the
Absence of Power  Full 10% Operating Range  Lithium Energy Source is Electrically
Disconnected to Retain Freshness Until
Power is Applied for the First Time  DIP Module Only Standard 32-Pin JEDEC Pinout Upward Compatible with the DS1248  PowerCap Module Board Only − Surface Mountable Package for Direct
Connection to PowerCap Containing
Battery and Crystal − Replaceable Battery (PowerCap) − Pin-for-Pin Compatible with Other
Densities of DS124xP Phantom Clocks  Underwriters Laboratories (UL) Recognized
(/qa/info/ul/)
PIN CONFIGURATIONS

13
10
11
12
14
31
Encapsulated Package
740-Mil Flush

A14 A7
A5
A4
A3
A2
A1
A0
DQ1
DQ0
VCC
A15
A17
WE
A13
A8
A9
A11
OE
A10
CE
DQ7
DQ5
DQ6
32
30
29
28
27
26
25
24
23
22
21
19
20 A16
A12
A6
A18/RST
DQ2
GND
15
16
18
17
DQ4
DQ3
DS1251
RST 2 A15
A16 N.C. VCC
WE
OE CE DQ7 DQ6
DQ5 DQ4
DQ3
DQ2 DQ1
DQ0
GND 6 9
10
11
12 13 14
15
16 17
A17 A14 33 32
31 30
29 28 27 26
25
24 23
22
21
20 19
18
A13
A12 A11
A10 A9 A8
A7 A6
A5 A4
A3
A2 A1
A0
34 A18
X1 GND VBAT X2
PowerCap Module Board
(Uses DS9034PCX+ PowerCap)
DS1251P

TOP VIEW
DS1251/DS1251P
4096K NV SRAM with Phantom Clock

19-6079; Rev 11/11
DS1251/DS1251P
ORDERING INFORMATION
PART TEMP RANGE VOLTAGE
RANGE (V) PIN-PACKAGE

DS1251W-120+ 0°C to +70°C 3.3 32 EDIP (0.740a)
DS1251W-120IND+ -40°C to +85°C 3.3 32 EDIP (0.740a)
DS1251WP-120+ 0°C to +70°C 3.3 34 PowerCap*
DS1251WP-120IND+ -40°C to +85°C 3.3 34 PowerCap*
DS1251Y-70+ 0°C to +70°C 5.0 32 EDIP (0.740a)
DS1251YP-70+ 0°C to +70°C 5.0 34 PowerCap*
DS1251YP-70IND+ -40°C to +85°C 5.0 34 PowerCap*
+ Denotes a lead(Pb)-free/RoHS-compliant package.
*DS9034PCX+ or DS9034I-PCX+ (PowerCap) required. Must be ordered separately.
PIN DESCRIPTION
PIN NAME FUNCTION EDIP PowerCap
1 RST Active-Low Reset Input. This pin has an internal pullup resistor connected to VCC. 34 A18
Address Inputs 3 A16 32 A14 30 A12 25 A7 24 A6 23 A5 22 A4 21 A3
10 20 A2
11 19 A1
12 18 A0
23 28 A10
25 29 A11
26 27 A9
27 26 A8
28 31 A13
30 33 A17
31 2 A15
13 16 DQ0
Data In/Data Out
14 15 DQ1
15 14 DQ2
17 13 DQ3
18 12 DQ4
19 11 DQ5
20 10 DQ6
21 9 DQ7
DS1251/DS1251P
PIN DESCRIPTION (continued)
PIN NAME FUNCTION EDIP PowerCap

22 8 CE Active-Low Chip-Enable Input
24 7 OE Active-Low Output-Enable Input
29 6 WE Active-Low Write-Enable Input
32 5 VCC Power-Supply Input 4 N.C. No Connection
16 17 GND Ground
DESCRIPTION

The DS1251 4096K NV SRAM with Phantom Clock is a fully static nonvolatile RAM (organized as
512K words by 8 bits) with a built-in real-time clock. The DS1251Y has a self-contained lithium energy
source and control circuitry, which constantly monitors VCC for an out-of-tolerance condition. When such
a condition occurs, the lithium energy source is automatically switched on and write protection is
unconditionally enabled to prevent garbled data in both the memory and real-time clock.
The phantom clock provides timekeeping information including hundredths of seconds, seconds, minutes,
hours, days, dates, months, and years. The date at the end of the month is automatically adjusted for
months with fewer than 31 days, including correction for leap years. The phantom clock operates in either
24-hour or 12-hour format with an AM/PM indicator.
PACKAGES

The DS1251 is available in two packages: 32-pin DIP and 34-pin PowerCap module. The 32-pin DIP
style module integrates the crystal, lithium energy source, and silicon in one package. The 34-pin
PowerCap module board is designed with contacts for connection to a separate PowerCap (DS9034PCX)
that contains the crystal and battery. This design allows the PowerCap to be mounted on top of the
DS1251P after the completion of the surface mount process. Mounting the PowerCap after the surface
mount process prevents damage to the crystal and battery because of the high temperatures required for
solder reflow. The PowerCap is keyed to prevent reverse insertion. The PowerCap Module Board and
PowerCap are ordered separately and shipped in separate containers.
RAM READ MODE

The DS1251 executes a read cycle whenever WE (write enable) is inactive (high) and CE (chip enable) is
active (low). The unique address specified by the 19 address inputs (A0–A18) defines which of the 512K
bytes of data is to be accessed. Valid data will be available to the eight data-output drivers within tACC
(access time) after the last address input signal is stable, providing that CE and OE (output enable) access
times and states are also satisfied. If OE and CE access times are not satisfied, then data access must be
measured from the later occurring signal (CE or OE) and the limiting parameter is either tCO for CE or
tOE for OE, rather than address access.
RAM WRITE MODE

The DS1251 is in the write mode whenever the WE and CE signals are in the active (low) state after
address inputs are stable. The latter occurring falling edge of CE or WE will determine the start of the
DS1251/DS1251P
be kept valid throughout the write cycle. WE must return to the high state for a minimum recovery time
(tWR ) before another cycle can be initiated. The OE control signal should be kept inactive (high) during
write cycles to avoid bus contention. However, if the output bus has been enabled (CE and OE active)
then WE will disable the outputs in tODW from its falling edge.
DATA RETENTION MODE

The 5V device is fully accessible and data can be written or read only when VCC is greater than VPF.
However, when VCC is below the power-fail point, VPF (point at which write protection occurs), the
internal clock registers and SRAM are blocked from any access. When VCC falls below the battery switch
point, VSO (battery supply level), device power is switched from the VCC pin to the backup battery. RTC
operation and SRAM data are maintained from the battery until VCC is returned to nominal levels.
The 3.3V device is fully accessible and data can be written or read only when VCC is greater than VPF.
When VCC falls below the power-fail point, VPF , access to the device is inhibited. If VPF is less than VBAT,
the device power is switched from VCC to the backup supply (VBAT ) when VCC drops below VPF . If VPF is
greater than VBAT, the device power is switched from VCC to the backup supply (VBAT ) when VCC drops
below VBAT. RTC operation and SRAM data are maintained from the battery until VCC is returned to
nominal levels.
All control, data, and address signals must be powered down when VCC is powered down.
PHANTOM CLOCK OPERATION

Communication with the phantom clock is established by pattern recognition on a serial bit stream of
64 bits, which must be matched by executing 64 consecutive write cycles containing the proper data on
DQ0. All accesses that occur prior to recognition of the 64-bit pattern are directed to memory.
After recognition is established, the next 64 read or write cycles either extract or update data in the
phantom clock, and memory access is inhibited.
Data transfer to and from the timekeeping function is accomplished with a serial bit stream under control
of chip enable, output enable, and write enable. Initially, a read cycle to any memory location using the and OE control of the phantom clock starts the pattern recognition sequence by moving a pointer to
the first bit of the 64-bit comparison register. Next, 64 consecutive write cycles are executed using the and WE control of the SmartWatch. These 64 write cycles are used only to gain access to the
phantom clock. Therefore, any address to the memory in the socket is acceptable. However, the write
cycles generated to gain access to the phantom clock are also writing data to a location in the mated
RAM. The preferred way to manage this requirement is to set aside just one address location in RAM as a
phantom clock scratch pad. When the first write cycle is executed, it is compared to bit 0 of the 64-bit
comparison register. If a match is found, the pointer increments to the next location of the comparison
register and awaits the next write cycle. If a match is not found, the pointer does not advance and all
subsequent write cycles are ignored. If a read cycle occurs at any time during pattern recognition, the
present sequence is aborted and the comparison register pointer is reset. Pattern recognition continues for
DS1251/DS1251P
from the timekeeping registers can proceed. The next 64 cycles will cause the phantom clock to either
receive or transmit data on DQ0, depending on the level of the OE pin or the WE pin. Cycles to other
locations outside the memory block can be interleaved with CE cycles without interrupting the pattern
recognition sequence or data transfer sequence to the phantom clock.
PHANTOM CLOCK REGISTER INFORMATION

The phantom clock information is contained in eight registers of 8 bits, each of which is sequentially
accessed 1 bit at a time after the 64-bit pattern recognition sequence has been completed. When updating
the phantom clock registers, each register must be handled in groups of 8 bits. Writing and reading
individual bits within a register could produce erroneous results. These read/write registers are defined in
Figure 2.
Data contained in the phantom clock register is in binary-coded decimal format (BCD). Reading and
writing the registers is always accomplished by stepping through all eight registers, starting with bit 0 of
register 0 and ending with bit 7 of register 7.
PHANTOM CLOCK REGISTER DEFINITION Figure 1

NOTE: THE PATTERN RECOGNITION IN HEX IS C5, 3A, A3, 5C, C5, 3A, A3, 5C. THE ODDS OF THIS PATTERN BEING ACCIDENTALLY

DUPLICATED AND CAUSING INADVERTENT ENTRY TO THE PHANTOM CLOCK IS LESS THAN 1 IN 1019. THIS PATTERN IS SENT TO
THE PHANTOM CLOCK LSB TO MSB.
DS1251/DS1251P
PHANTOM CLOCK REGISTER DEFINITION Figure 2

AM/PM/12/24 MODE

Bit 7 of the hours register is defined as the 12-hour or 24-hour mode-select bit. When high, the 12-hour
mode is selected. In the 12-hour mode, bit 5 is the AM/PM bit with logic high being PM. In the 24-hour
mode, bit 5 is the 20-hour bit (20–23 hours).
OSCILLATOR AND RESET BITS

Bits 4 and 5 of the day register are used to control the RST and oscillator functions. Bit 4 controls the
RST (pin 1). When the RST bit is set to logic 1, the RST input pin is ignored. When the RST bit is set to
logic 0, a low input on the RST pin will cause the phantom clock to abort data transfer without changing
data in the watch registers. Bit 5 controls the oscillator. When set to logic 1, the oscillator is off. When set
to logic 0, the oscillator turns on and the watch becomes operational. These bits are shipped from the
factory set to a logic 1.
ZERO BITS

Registers 1, 2, 3, 4, 5, and 6 contain one or more bits, which will always read logic 0. When writing these
DS1251/DS1251P
BATTERY LONGEVITY

The DS1251 has a lithium power source that is designed to provide energy for clock activity, and clock
and RAM data retention when the VCC supply is not present. The capability of this internal power supply
is sufficient to power the DS1251 continuously for the life of the equipment in which it is installed. For
specification purposes, the life expectancy is 10 years at +25°C with the internal clock oscillator running
in the absence of VCC power. Each DS1251 is shipped from Maxim with its lithium energy source
disconnected, guaranteeing full energy capacity. When VCC is first applied at a level greater than VPF, the
lithium energy source is enabled for battery-backup operation. Actual life expectancy of the DS1251 will
be much longer than 10 years since no lithium battery energy is consumed when VCC is present.
CLOCK ACCURACY (DIP MODULE)

The DS1251 is guaranteed to keep time accuracy to within ±1 minute per month at +25°C. The clock is
calibrated at the factory by Maxim using special calibration nonvolatile tuning elements. The DS1251
does not require additional calibration and temperature deviations will have a negligible effect in most
applications. For this reason, methods of field clock calibration are not available and not necessary.
CLOCK ACCURACY (POWERCAP MODULE)

The DS1251P and DS9034PCX are each individually tested for accuracy. Once mounted together, the
module is guaranteed to keep time accuracy to within ±1.53 minutes per month (35ppm) at +25°C.
DS1251/DS1251P
ABSOLUTE MAXIMUM RATINGS

Voltage Range on Any Pin Relative to Ground (5V product) . . . . . . . . . . . . . . . . . . . -0.3V to +6.0V (3.3V product) . . . . . . . . . . . . . . . . . -0.3V to +4.6V
Storage Temperature Range EDIP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-40°C to +85°C PowerCap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -55°C to +125°C
Lead Temperature (soldering, 10s) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +260°C Note: EDIP is wave or hand-soldered only
Soldering Temperature (reflow, PowerCap) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .+260°C
This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in
the operation sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended
periods of time can affect reliability.
OPERATING RANGE
RANGE TEMP RANGE
(NONCONDENSING) VCC (V)

Commercial 0°C to +70°C 3.3 ±10% or 5 ±10%
Industrial -40°C to +85°C 3.3 ±10% or 5 ±10%
RECOMMENDED OPERATING CONDITIONS

(TA = Over the operating range.)
PARAMETER SYMBOL MIN TYP MAX UNITS NOTES

Logic 1 Voltage All
Inputs
VCC = 5V ±10%
VIH
2.2 VCC + 0.3 11
VCC = 3.3V ±10% 2.0 VCC + 0.3
Logic 0 Voltage All
Inputs
VCC = 5V ±10%
VIL
-0.3 +0.8 11
VCC = 3.3V ±10% -0.3 +0.6
DS1251/DS1251P
DC ELECTRICAL CHARACTERISTICS

(TA = Over the operating range.) (5V)
0BPARAMETER SYMBOL MIN TYP MAX UNITS NOTES
Input Leakage Current IIL -1.0 +1.0 µA 12
I/O Leakage Current
CE ≥ VIH ≤ VCC IIO -1.0 +1.0 µA
Output Current at 2.4V IOH -1.0 mA
Output Current at 0.4V IOL 2.0 mA
Standby Current CE = 2.2V ICCS1 5 10 mA
Standby Current
CE = VCC - 0.5V ICCS2 3.0 5.0 mA
Operating Current tCYC = 70ns ICC01 85 mA
Write Protection Voltage VPF 4.25 4.37 4.50 V 11
Battery Switchover Voltage VSO VBAT 6BV 11
DC ELECTRICAL CHARACTERISTICS

(TA = Over the operating range.) (3.3V)
1BPARAMETER SYMBOL MIN TYP MAX UNITS NOTES
Input Leakage Current IIL -1.0 +1.0 µA 12
I/O Leakage Current
CE ≥ VIH ≤ VCC IIO -1.0 +1.0 µA
Output Current at 2.4V IOH -1.0 mA
Output Current at 0.4V IOL 2.0 mA
Standby Current CE = 2.2V ICCS1 5 7 mA
Standby Current
CE = VCC - 0.5V ICCS2 2.0 3.0 mA
Operating Current tCYC = 70ns ICC01 50 mA
Write Protection Voltage VPF 2.80 2.97 V 11
Battery Switchover Voltage VSO VBAT or
VPF 7BV 11
CAPACITANCE

(TA = +25°C)
2BPARAMETER SYMBOL MIN TYP MAX UNITS NOTES
Input Capacitance CIN 5 10 pF
Input/Output Capacitance CI/O 5 10 pF
DS1251/DS1251P
MEMORY AC ELECTRICAL CHARACTERISTICS

(TA = Over the operating range.) (5V)
3BPARAMETER SYMBOL DS1251Y-70 UNITS 8BNOTES MIN 9BMAX
Read Cycle Time tRC 70 ns
Access Time tACC 70 ns
OE to Output Valid tOE 35 ns
CE to Output Valid tCO 70 ns
OE or CE to Output Active tCOE 5 ns 5
Output High-Z from Deselection tOD 25 ns 5
Output Hold from Address Change tOH 5 ns
Write Cycle Time tWC 70 ns
Write Pulse Width tWP 50 ns 3
Address Setup Time tAW 0 ns
Write Recovery Time tWR 0 ns
Output High-Z from WE tODW 25 ns 5
Output Active from WE tOEW 5 ns 5
Data Setup Time tDS 30 ns 4
Data Hold Time from WE tDH 5 ns 4
ic,good price


TEL:86-533-2716050      FAX:86-533-2716790
   

©2020 IC PHOENIX CO.,LIMITED