IC Phoenix
 
Home ›  DD23 > DS1245-DS1245AB-100-DS1245AB-120-DS1245AB-120.-DS1245AB-70-DS1245ABP-100IND+-DS1245Y-100-DS1245Y-120-DS1245Y-70-DS1245Y-85-DS1245YP-100IND+,1024K Nonvolatile SRAM
DS1245-DS1245AB-100-DS1245AB-120-DS1245AB-120.-DS1245AB-70 Fast Delivery,Good Price
Part Number:
If you need More Quantity or Better Price,Welcom Any inquiry.
We available via phone +865332716050 Email
Partno Mfg Dc Qty AvailableDescript
DS1245DSN/a2000avai3.3V 1024k Nonvolatile SRAM
DS1245AB-100 |DS1245AB100DALLASN/a1000avai1024K Nonvolatile SRAM
DS1245AB-120 |DS1245AB120N/a1avai1024K Nonvolatile SRAM
DS1245AB-120. |DS1245AB120DALLASN/a11avai1024K Nonvolatile SRAM
DS1245AB-70 |DS1245AB70DALLASN/a2000avai1024K Nonvolatile SRAM
DS1245ABP-100IND+ |DS1245ABP100INDDALLASN/a5avai1024k Nonvolatile SRAM
DS1245Y-100 |DS1245Y100DALLASN/a4130avai1024K Nonvolatile SRAM
DS1245Y-100 |DS1245Y100DSN/a200avai1024K Nonvolatile SRAM
DS1245Y-120 |DS1245Y120DSN/a200avai1024K Nonvolatile SRAM
DS1245Y-70 |DS1245Y70DALLASN/a3198avai1024K Nonvolatile SRAM
DS1245Y-70 |DS1245Y70DALLAS,DALLAN/a25000avai1024K Nonvolatile SRAM
DS1245Y-85 |DS1245Y85DALLAS特价N/a500avai1024K Nonvolatile SRAM
DS1245YP-100IND+ |DS1245YP100INDDALLASN/a5avai1024k Nonvolatile SRAM


DS1245Y-70 ,1024K Nonvolatile SRAMFEATURES PIN ASSIGNMENT 10 years minimum data retention in theNC 32 V1 CCabsence of external power ..
DS1245Y-70 ,1024K Nonvolatile SRAMDS1245Y/AB1024k Nonvolatile SRAMwww.dalsemi.com
DS1245Y-70+ ,1024k Nonvolatile SRAMFEATURES PIN ASSIGNMENT  10 years minimum data retention in the NC 1 32 V CCabsence of externa ..
DS1245Y-70IND ,1024k Nonvolatile SRAM19-5638; Rev 11/10 DS1245Y/AB 1024k Nonvolatile SRAM www .maxim-ic.com
DS1245Y-70IND ,1024k Nonvolatile SRAM19-5638; Rev 11/10 DS1245Y/AB 1024k Nonvolatile SRAM www .maxim-ic.com
DS1245Y-70IND. ,1024k Nonvolatile SRAMFEATURES PIN ASSIGNMENT  10 years minimum data retention in the NC 1 32 V CCabsence of externa ..
DTB114GK , −500mA / −50V Digital transistors (with built-in resistors)
DTB122JK , Digital transistor (built-in resistors)
DTB123 , Digital transistors (built-in resistors)
DTB123E , DIGITAL TRANSISTOR
DTB123EK , -500mA / -50V Digital transistors (with built-in resistors)
DTB123EK , -500mA / -50V Digital transistors (with built-in resistors)


DS1245-DS1245AB-100-DS1245AB-120-DS1245AB-120.-DS1245AB-70-DS1245ABP-100IND+-DS1245Y-100-DS1245Y-120-DS1245Y-70-DS1245Y-85-DS1245YP-100IND+
1024k Nonvolatile SRAM
FEATURES10 years minimum data retention in the
absence of external powerData is automatically protected during powerlossReplaces 128k x 8 volatile static RAM,
EEPROM or Flash memoryUnlimited write cyclesLow-power CMOSRead and write access times as fast as 70 nsLithium energy source is electrically
disconnected to retain freshness until power is
applied for the first timeFull ±10% VCC operating range (DS1245Y)Optional ±5% VCC operating range
(DS1245AB)Optional industrial temperature range of
-40°C to +85°C, designated INDJEDEC standard 32-pin DIP packageNew PowerCap Module (PCM) packageDirectly surface-mountable moduleReplaceable snap-on PowerCap provideslithium backup batteryStandardized pinout for all nonvolatile
SRAM productsDetachment feature on PowerCap allows
easy removal using a regular screwdriver
PIN ASSIGNMENT
PIN DESCRIPTION

A0 - A16 - Address Inputs
DQ0 - DQ7 - Data In/Data Out - Chip Enable - Write Enable - Output Enable
VCC - Power (+5V)GND - Ground
DS1245Y/AB
1024k Nonvolatile SRAM

32-PIN ENCAPSULATED PACKAGE
740 MIL EXTENDED
A14
DQ1
DQ0
VCC
DQ7
DQ5
DQ6
A16
A12
DQ2
GND
DQ4
DQ3NCA15A16NCVCC
WEOECEDQ7DQ6DQ5DQ4DQ3DQ2DQ1DQ0GNDNC
34-PIN POWERCAP MODULE (PCM)
(USES DS9034PC POWERCAP)
DS1245Y/AB
DESCRIPTION

The DS1245 1024k Nonvolatile SRAMs are1,048,576-bit, fully static, nonvolatile SRAMs organized as
131,072 words by 8 bits. Each complete NV SRAM has a self-contained lithium energy source and
control circuitry which constantly monitors VCC for an out-of-tolerance condition. When such a condition
occurs, the lithium energy source is automatically switched on and write protection is unconditionally
enabled to prevent data corruption. DIP-package DS1245 devices can be used in place of existing 128k x8 static RAMs directly conforming to the popular bytewide 32-pin DIP standard. DS1245 devices in the
PowerCap Module package are directly surface mountable and are normally paired with a DS9034PC
PowerCap to form a complete Nonvolatile SRAM module. There is no limit on the number of write
cycles that can be executed and no additional support circuitry is required for microprocessor interfacing.
READ MODE

The DS1245 executes a read cycle whenever WE (Write Enable) is inactive (high) and CE (Chip Enable)
and OE (Output Enable) are active (low). The unique address specified by the 17 address inputs (A0 -
A16) defines which of the 131,072 bytes of data is to be accessed. Valid data will be available to the eightdata output drivers within tACC (Access Time) after the last address input signal is stable, providing that and OE (Output Enable) access times are also satisfied. If OE and CE access times are not satisfied,
then data access must be measured from the later occurring signal (CE or OE) and the limiting parameter
is either tCO for CE or tOE for OE rather than address access.
WRITE MODE

The DS1245 executes a write cycle whenever the WE and CE signals are active (low) after address
inputs are stable. The later occurring falling edge of CE or WE will determine the start of the write cycle.
The write cycle is terminated by the earlier rising edge of CE or WE. All address inputs must be kept
valid throughout the write cycle. WE must return to the high state for a minimum recovery time (tWR)
before another cycle can be initiated. The OE control signal should be kept inactive (high) during write
cycles to avoid bus contention. However, if the output drivers are enabled (CE and OE active) then WE
will disable the outputs in tODW from its falling edge.
DATA RETENTION MODE

The DS1245AB provides full functional capability for VCC greater than 4.75 volts and write protects by4.5 volts. The DS1245Y provides full functional capability for VCC greater than 4.5 volts and write-
protects by 4.25 volts. Data is maintained in the absence of VCC without any additional support circuitry.
The nonvolatile static RAMs constantly monitor VCC. Should the supply voltage decay, the NV SRAMs
automatically write-protect themselves, all inputs become “don’t care,” and all outputs become high
impedance. As VCC falls below approximately 3.0 volts, a power switching circuit connects the lithiumenergy source to RAM to retain data. During power-up, when VCC rises above approximately 3.0 volts,
the power switching circuit connects external VCC to RAM and disconnects the lithium energy source.
Normal RAM operation can resume after VCC exceeds 4.75 volts for the DS1245AB and 4.5 volts for the
DS1245Y.
FRESHNESS SEAL

Each DS1245 device is shipped from Dallas Semiconductor with its lithium energy source disconnected,guaranteeing full energy capacity. When VCC is first applied at a level greater than 4.25 volts, the lithium
energy source is enabled for battery back-up operation.
DS1245Y/AB
PACKAGES

The DS1245 devices are available in two packages: 32-pin DIP and 34-pin PowerCap Module (PCM).
The 32-pin DIP integrates a lithium battery, an SRAM memory and a nonvolatile control function into a
single package with a JEDEC-standard 600-mil DIP pinout. The 34-pin PowerCap Module integrates
SRAM memory and nonvolatile control along with contacts for connection to the lithium battery in the
DS9034PC PowerCap. The PowerCap Module package design allows a DS1245 PCM device to besurface mounted without subjecting its lithium backup battery to destructive high-temperature reflow
soldering. After a DS1245 PCM is reflow soldered, a DS9034PC PowerCap is snapped on top of the
PCM to form a complete Nonvolatile SRAM module. The DS9034PC is keyed to prevent improper
attachment. DS1245 PowerCap Modules and DS9034PC PowerCaps are ordered separately and shipped
in separate containers. See the DS9034PC data sheet for further information.
ABSOLUTE MAXIMUM RATINGS*

Voltage on Any Pin Relative to Ground -0.3V to +7.0VOperating Temperature 0°C to 70°C, -40°C to +85°C for Ind parts
Storage Temperature -40°C to +70°C, -40°C to +85°C for Ind parts
Soldering Temperature 260°C for 10 secondsThis is a stress rating only and functional operation of the device at these or any other conditionsabove those indicated in the operation sections of this specification is not implied. Exposure to
absolute maximum rating conditions for extended periods of time may affect reliability.
RECOMMENDED DC OPERATING CONDITIONS (tA: See Note 10)
DC ELECTRICAL (VCC=5V ±=5% for DS1245AB)
CHARACTERISTICS (tA: See Note 10) (VCC=5V ±=10% for DS1245Y)
DS1245Y/AB
CAPACITANCE (tA=25°C)
AC ELECTRICAL (VCC=5V ±=5% for DS1245AB)
CHARACTERISTICS (tA: See Note 10) (VCC=5V ±=10% for DS1245Y)
DS1245Y/AB
AC ELECTRICAL (VCC=5V ±=5% for DS1245AB)
CHARACTERISTICS (tA: See Note 10) (VCC=5V ±=10% for DS1245Y)
DS1245Y/AB
READ CYCLE

SEE NOTE 1
WRITE CYCLE 1

SEE NOTES 2, 3, 4, 6, 7, 8, and 12
ic,good price


TEL:86-533-2716050      FAX:86-533-2716790
   

©2020 IC PHOENIX CO.,LIMITED