IC Phoenix
 
Home ›  DD21 > DS1088L-DS1088LU-02-DS1088LU-66,Low-Cost Fixed-Frequency EconOscillator
DS1088L-DS1088LU-02-DS1088LU-66 Fast Delivery,Good Price
Part Number:
If you need More Quantity or Better Price,Welcom Any inquiry.
We available via phone +865332716050 Email
Partno Mfg Dc Qty AvailableDescript
DS1088LDSN/a40avaiLow-Cost Fixed-Frequency EconOscillator
DS1088LU-02 |DS1088LU02MAXIM ?N/a524avaiLow-Cost Fixed-Frequency EconOscillator
DS1088LU-66 |DS1088LU66DallasN/a340avaiLow-Cost Fixed-Frequency EconOscillator


DS1088LU-02 ,Low-Cost Fixed-Frequency EconOscillatorApplications♦ Power-Down ModePrinters♦ 1.0% Frequency Tolerance Over Temperature Copiersand Voltage ..
DS1088LU-02A+ ,Fixed-Frequency EconOscillator™Applications● 1% Frequency Tolerance Over Temperature and ● PrintersVoltage● Copiers● Wide Temperat ..
DS1088LU-66 ,Low-Cost Fixed-Frequency EconOscillatorELECTRICAL CHARACTERISTICS(V = 2.7V to 3.6V, T = -20°C to +85°C.)CC APARAMETER SYMBOL CONDITIONS MI ..
DS1089L ,3.3V Center Spread`Spectrum EconOscillatorApplications♦ Programmable Output Power-Down/Disable ModeAutomotive InfotainmentPrintersCopiers Ord ..
DS1089LU-A29+T ,3.3V Center Spread-Spectrum EconOscillator™Applications● Power-Down Mode● Printers● Programmable Output Power-Down/Disable Mode● Copiers● Comp ..
DS1090U-16 ,250 kHz to 500 kHz, Low-frequency, spread-spectrum econ oscillatorELECTRICAL CHARACTERISTICS(V = +3.0V to +5.5V, T = -40°C to +85°C, unless otherwise noted.)CC APARA ..
DTA113TKA , Digital transistor (built in resistor)
DTA113TKA , Digital transistor (built in resistor)
DTA113ZE , PNP -100mA -50V Digital Transistors (Bias Resistor Built-in Transistors)
DTA113ZUA , PNP -100mA -50V Digital Transistors (Bias Resistor Built-in Transistors)
DTA114 EK , DTA/DTC SERIES
DTA114ECA , Built-In Bias Resistors Enable The Configuration of An Inverter Circuit Without Connecting External Input Resistors


DS1088L-DS1088LU-02-DS1088LU-66
Low-Cost Fixed-Frequency EconOscillator
General Description
The DS1088L is a low-cost clock generator that pro-
duces a square-wave output without external timing
components. The fixed-frequency oscillator is available
in factory-calibrated frequencies from 312kHz to
133MHz. The DS1088L has a power-down pin for
power-sensitive applications.
Applications

Printers
Copiers
Automotive Telematics
Computer Peripherals
POS Terminals
Cable Modems
Features
Factory-Programmed, Square-Wave Generator
from 312kHz to 133MHz
Single OutputNo External Timing Components Required2.7V to 3.6V SupplyPower-Down Mode1.0% Frequency Tolerance Over Temperature
and Voltage
Wide Temperature Range (-20°C to +85°C)
DS1088L
Low-Cost Fixed-Frequency EconOscillator™
Pin Configuration
Typical Operating Circuit
Ordering Information

Rev 1; 5/05
EconOscillator is a trademark of Dallas Semiconductor.
DS1088L
Low-Cost Fixed-Frequency EconOscillator™
ABSOLUTE MAXIMUM RATINGS
RECOMMENDED OPERATING CONDITIONS

Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
DC ELECTRICAL CHARACTERISTICS

Voltage Range on VCCRelative to Ground ..........-0.5V to +6.0V
Voltage Range on PDNRelative
to Ground*..............................................-0.5V to (VCC+ 0.5V)
Operating Temperature Range...........................-20°C to +85°C
Storage Temperature Range ............................-55°C to +125°C
Soldering Temperature ....................See IPC/JEDEC J-STD-020
*Not to exceed +6.0V.
DS1088L
Low-Cost Fixed-Frequency EconOscillator™
OSCILLATOR CHARACTERISTICS
AC ELECTRICAL CHARACTERISTICS
Note 2:
This is the change in output frequency due to changes in voltage at TA= +25°C.
Note 3:
This is the change in output frequency due to changes in temperature from the +25°C frequency at VCC= 3.3V.
Note 4:
Guaranteed by design.
Note 5:
This indicates the time elapsed between power-up and the output becoming active. An on-chip delay is intentionally intro-
duced to allow the oscillator to stabilize. tSTABis equivalent to approximately 512 clock cycles and will depend on the pro-
grammed oscillator frequency.
Note 6:
Output disabled in 2 cycles or less of the output frequency.
Note 7:
Output voltage swings may be impaired at high frequencies combined with high-output loading.
Note 8:
Typical frequency shift due to aging is within ±0.2%. Aging stressing includes level 1 moisture reflow preconditioning (24hr
+125°C bake, 168hr +85°C/85%RH moisture soak, and three solder reflow passes +240°C +0°C/-5°C peak) followed by
1000hr (max) VCCbiased +125°C OP/L, 1000hr unbiased +150°C bake, 1000 temperature cycles at -55°C to +125°C and
168hr +121°C/2 ATM steam/unbiased autoclave.
DS1088L
Low-Cost Fixed-Frequency EconOscillator™
Typical Operating Characteristics

(VCC= 3.3V, TA= +25°C, unless otherwise noted.)
DS1088L
Low-Cost Fixed-Frequency EconOscillator™

Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
Detailed Description

The DS1088L is a low-cost clock generator that pro-
duces a square-wave output without external timing
components. The fixed-frequency oscillator is available
in factory-calibrated frequencies from 312kHz to
133MHz. The DS1088L has a power-down pin for
power-sensitive applications. A block diagram of the
DS1088L is shown in Figure1.
Output Frequency

The internal oscillator frequency is divided by the facto-
ry-programmed prescaler to produce an output fre-
quency of 312kHz to 133MHz. See the Standard
Frequency Optionstablefor a list of standard frequen-
cies. Contact factory for custom frequencies.
Power-Down Mode

The PDNpin disables the internal oscillator and the
oscillator output for power-sensitive applications. The
power-down pin must remain low for at least two output
frequency cycles plus 10µs for deglitching purposes.
On power-up, the output is disabled until power is sta-
ble and the voltage-controlled oscillator has generated
512 clock cycles.
Applications Information
Power-Supply Decoupling

To achieve the best results when using the DS1088L,
the power supply must be decoupled with 0.01µF and
0.1µF high-quality, ceramic, surface-mount capacitors.
Surface-mount components minimize lead inductance,
which improves performance, and tend to have ade-
quate high-frequency response for decoupling applica-
tions. These capacitors should be placed as close to
the VCCand GND pins as possible.
Chip Topology

TRANSISTOR COUNT: 4507
SUBSTRATE CONNECTED TO GROUND.
Package Information

For the latest package outline information, go to
Figure 1. Block Diagram
This datasheet has been :
www.ic-phoenix.com
Datasheets for electronic components.
ic,good price


TEL:86-533-2716050      FAX:86-533-2716790
   

©2020 IC PHOENIX CO.,LIMITED