IC Phoenix
 
Home ›  BB32 > BTS443P,Smart Highside Power Switch
BTS443P Fast Delivery,Good Price
Part Number:
If you need More Quantity or Better Price,Welcom Any inquiry.
We available via phone +865332716050 Email
Partno Mfg Dc Qty AvailableDescript
BTS443PINFINEONN/a2049avaiSmart Highside Power Switch


BTS443P ,Smart Highside Power Switchapplications!*) *) Not shorting all outputs will considerably increase the on-state resistance, re ..
BTS452R ,Smart Power High-Side-SwitchFeatures Product Summary• Overload protection Overvoltage protection V 62 Vbb(AZ)• Current limitati ..
BTS452R ,Smart Power High-Side-SwitchBlock Diagram+ VbbVoltageGateOvervoltage Currentsource protection limitprotectionVLogicOUTLimit for ..
BTS452T ,Smart Power High-Side-SwitchBlock Diagram+ VbbVoltageOvervoltage Current Gatesourceprotection limit protectionVLogicOUTLimit fo ..
BTS452T . ,Smart Power High-Side-SwitchFeatures Product Summary• Overload protection Overvoltage protection V 62 Vbb(AZ)• Current limitati ..
BTS462T ,Smart Power High-Side-SwitchFeatures Product Summary• Overload protection Overvoltage protection V 41 Vbb(AZ)• Current limitati ..
BZX84-C5V1 ,Voltage regulator diodesGeneral descriptionLow-power voltage regulator diodes in a small SOT23 (TO-236AB) Surface-Mounted D ..
BZX84C-5V1 ,Voltage regulator diodesGeneral descriptionLow-power voltage regulator diodes in a small SOT23 (TO-236AB) Surface-Mounted D ..
BZX84C5V1LT1 ,SEMICONDUCTOR(TECHNICAL DATA)ELECTRICAL CHARACTERISTICS − BZX84BxxxL (Tight Tolerance Series)(Pinout: 1-Anode, 2-No Connection, ..
BZX84C5V1LT1G , Zener Voltage Regulators
BZX84C5V1T-7-F , 150mW SURFACE MOUNT ZENER DIODE
BZX84C5V1TS-7-F , TRIPLE SURFACE MOUNT ZENER DIODE ARRAY


BTS443P
Smart Highside Power Switch
PROFET® Data Sheet BTS 443 P
Smart Highside Power Switch
Reversave

• Reverse battery protection by self turn on of
power MOSFET
Features

• Short circuit protection
• Current limitation
• Overload protection
• Thermal shutdown
• Overvoltage protection (including load dump)
• Loss of ground protection
• Loss of Vbb protection (with external diode for
charged inductive loads)
• Very low standby current
• Fast demagnetisation of inductive loads
• Electrostatic discharge (ESD) protection
• Optimized static electromagnetic compatibility (EMC)
Diagnostic Function

• Proportional load current sense (with defined fault signal during thermal shutdown)
Application

• Power switch with current sense diagnostic feedback for 12V and 24 V DC grounded loads
• All types of resistive, capacitive and inductive loads (no PWM with inductive loads)
• Replaces electromechanical relays, fuses and discrete circuits
General Description

N channel vertical power FET with charge pump, current controlled input and diagnostic feedback with load
current sense, integrated in Smart SIPMOS chip on chip technology. Providing embedded protective functions.
PROFET
Load GNDL
VIS
IIN
Logic GNDIN
Package
Data Sheet BTS 443 P
*) Not shorting all outputs will considerably increase the on-state resistance, reduce the peak current capability
and decrease the current sense accuracy
Maximum Ratings at Tj = 25 °C unless otherwise specified

) Short circuit is tested with 100mΩ and 20µH
2) VLoad dump is set-up without the DUT connected to the generator per ISO 7637-1 and DIN 40839
Data Sheet BTS 443 P
Thermal Characteristics


3) Thermal resistance RthCH case to heatsink (about 0.5 ... 0.9 K/W with silicone paste) not included! Device on 50mm*50mm*1.5mm epoxy PCB FR4 with 6cm2 (one layer, 70µm thick) copper area for Vbb
connection. PCB is vertical without blown air.
Electrical Characteristics
Load Switching Capabilities and Characteristics
Data Sheet BTS 443 P
Operating Parameters

Protection Functions 7)
Reverse Battery


5) VbIN=Vbb-VIN see diagram on page 11.
6) see also VON(CL) in circuit diagram on page 7.
7) Integrated protection functions are designed to prevent IC destruction under fault condition described in the
data sheet. Fault conditions are considered as “outside” normal operating range. Protection functions are not
Data Sheet BTS 443 P
Diagnostic Characteristics

If VON is higher, the sense current is no longer proportional to the load current due to sense current
Input

Data Sheet BTS 443 P
Truth Table

L = "Low" Level Z = high impedance, potential depends on external circuit
H = "High" Level

11) Low ohmic short to Vbb may reduce the output current IL and therefore also the sense current IIS.
Terms
ININbbOUTbIN
Two or more devices can easily be connected in
parallel to increase load current capability.
Data Sheet BTS 443 P
Input circuit (ESD protection)

Vbb
VbIN
VIN
ESD-Zener diode: 68 V typ., max 15 mA;
Current sense output

Normal operation V
VZ,IS = 68 V (typ.), RIS = 1 kΩ nominal (or 1 kΩ /n, if n
devices are connected in parallel). IS = IL/kilis can be
only driven by the internal circuit as long as
Vout - VIS > 5V. If you want to measure load currents
up to IL(M), RIS should be less than
ilisMLIV(.
Note: For large values of RIS the voltage VIS can reach
almost Vbb. See also overvoltage protection.
If you don't use the current sense output in your
application, you can leave it open.
Inductive and overvoltage output clamp

PROFET
VON is clamped to VON(Cl) = 42 V typ.
Overvoltage protection of logic part

Signal GND
Rbb = 200 Ω typ., VZ,IN = VZ,IS = 68 V typ., RIS = 1 kΩ
nominal. Note that when overvoltage exceeds 73 V typ.
a voltage above 5V can occur between IS and GND, if
RV, VZ,VIS are not used.
ic,good price


TEL:86-533-2716050      FAX:86-533-2716790
   

©2020 IC PHOENIX CO.,LIMITED