IC Phoenix
 
Home ›  BB32 > BTS410F2-BTS410F2 E3062A,Smart Highside Power Switch
BTS410F2-BTS410F2 E3062A Fast Delivery,Good Price
Part Number:
If you need More Quantity or Better Price,Welcom Any inquiry.
We available via phone +865332716050 Email
Partno Mfg Dc Qty AvailableDescript
BTS410F2INFN/a10avaiSmart Highside Power Switch (Overload protection Current limitation Short circuit protection Thermal shutdown)
BTS410F2 E3062A |BTS410F2E3062AINFINEONN/a2500avaiSmart Highside Power Switch


BTS410F2 E3062A ,Smart Highside Power SwitchCharacteristics Parameter and Conditions Symbol Values Unit min typ max Thermal resistance chip - ..
BTS410G2 ,PROFET Smart High Side Power SwitchGeneral DescriptionN channel vertical power FET with charge pump, ground referenced CMOS compatible ..
BTS410H2 ,PROFET Smart High Side Power SwitchGeneral DescriptionN channel vertical power FET with charge pump, ground referenced CMOS compatible ..
BTS412B2 ,Smart Highside Power Switch (Overload protection Current limitation Short circuit protection Thermal shutdown)General DescriptionN channel vertical power FET with charge pump, ground referenced CMOS compatible ..
BTS4130QGA , Smart High-Side Power Switch
BTS4130QGA , Smart High-Side Power Switch
BZX84C4V7 ,350mW ZENER DIODE 3.3 VOLTS THRU 33 VOLTS 5% TOLERANCEFeatures

BTS410F2-BTS410F2 E3062A
Smart Highside Power Switch
Smart Highside Power Switch
Features

• Overload protection
• Current limitation
• Short circuit protection
• Thermal shutdown
• Overvoltage protection (including load dump)
• Fast demagnetization of inductive loads
• Reverse battery protection1)
• Undervoltage and overvoltage shutdown with
auto-restart and hysteresis
• Open drain diagnostic output Open load detection in ON-state
• CMOS compatible input
• Loss of ground and loss of Vbb protection
• Electrostatic discharge (ESD) protection
Application

• µC compatible power switch with diagnostic feedback for 12 V and 24 V DC grounded loads
• Most suitable for inductive loads
• Replaces electromechanical relays, fuses and discrete circuits
General Description

N channel vertical power FET with charge pump, ground referenced CMOS compatible input and diagnostic
feedback, monolithically integrated in Smart SIPMOS technology. Providing embedded protective functions. bb
Signal GND
PROFET
Load GND
VLogic

Product Summary

Maximum Ratings at Tj = 25 °C unless otherwise specified
Thermal Characteristics

Supply voltages higher than Vbb(AZ) require an external current limit for the GND and status pins, e.g. with a
150 Ω resistor in the GND connection and a 15 kΩ resistor in series with the status pin. A resistor for the
protection of the input is integrated.
3) RI = internal resistance of the load dump test pulse generator
4) VLoad dump is setup without the DUT connected to the generator per ISO 7637-1 and DIN 40839
Electrical Characteristics
Load Switching Capabilities and Characteristics

Operating Parameters


6) At supply voltage increase up to Vbb= 5.6 V typ without charge pump, VOUT ≈Vbb - 2 V
BTS 410 F2 Protection Functions
Diagnostic Characteristics

) Integrated protection functions are designed to prevent IC destruction under fault conditions described in the
data sheet. Fault conditions are considered as “outside” normal operating range. Protection functions are not
designed for continuous repetitive operation.
10) Short circuit current limit for max. duration of td(SC) max=450 µs, prior to shutdown
11) Requires 150 Ω resistor in GND connection. The reverse load current through the intrinsic drain-source
diode has to be limited by the connected load. Note that the power dissipation is higher compared to normal
operating conditions due to the voltage drop across the intrinsic drain-source diode. The temperature
protection is not active during reverse current operation! Input and Status currents have to be limited (see
BTS 410 F2 Input and Status Feedback)

12) If a ground resistor RGND is used, add the voltage drop across this resistor.
Truth Table
L = "Low" Level X = don't care Z = high impedance, potential depends on external circuit
H = "High" Level Status signal after the time delay shown in the diagrams (see fig 5. page 12...13)

13) Power Transistor off, high impedance, versions BTS 410H, BTS 412B: internal pull up current source for
open load detection.
14) Low resistance short Vbb to output may be detected in ON-state by the no-load-detection
15) No current sink capability during undervoltage shutdown
Terms
PROFET
IN
OUT
GNDSTVIN
ISTINbb
IbbLOUTIGNDONGND
Input circuit (ESD protection)

ZDI1 6 V typ., ESD zener diodes are not to be used as
voltage clamp at DC conditions. Operation in this mode
may result in a drift of the zener voltage (increase of up
to 1 V).


ic,good price


TEL:86-533-2716050      FAX:86-533-2716790
   

©2020 IC PHOENIX CO.,LIMITED