IC Phoenix
 
Home ›  AA42 > ADV7192KST,Video Encoder with Six 10-Bit DACs, 54 MHz Oversampling and Progressive Scan Inputs
ADV7192KST Fast Delivery,Good Price
Part Number:
If you need More Quantity or Better Price,Welcom Any inquiry.
We available via phone +865332716050 Email
Partno Mfg Dc Qty AvailableDescript
ADV7192KSTADN/a51avaiVideo Encoder with Six 10-Bit DACs, 54 MHz Oversampling and Progressive Scan Inputs


ADV7192KST ,Video Encoder with Six 10-Bit DACs, 54 MHz Oversampling and Progressive Scan InputsFEATURES: FUNCTIONAL DESCRIPTION . . . . . . . . . 17BRIGHTNESS DETECT REGISTER . . . . . . . . . . ..
ADV7192KSTZ ,Video Encoder with Six 10-bit DACs, 54 MHz Oversampling and ProgressiveFEATURES: FUNCTIONAL DESCRIPTION . . . . . . . . . 17DNR BIT DESCRIPTIONS . . . . . . . . . . . . . ..
ADV7194KST ,Professional Extended-10⑩ Video Encoder with 54 MHz OversamplingFEATURES: FUNCTIONAL DESCRIPTION . . . . . . . . . 17BRIGHTNESS DETECT REGISTER . . . . . . . . . . ..
ADV7194KSTZ ,Professional Extended-10™ Video Encoder with 54 MHz OversamplingFEATURES: FUNCTIONAL DESCRIPTION . . . . . . . . . 17BRIGHTNESS DETECT REGISTER . . . . . . . . . . ..
ADV7196AKS ,Multiformat Progressive Scan/HDTV Encoder with Three 11-Bit DACs, 10-Bit Data Input, and MacrovisionGENERAL DESCRIPTIONAnticopy algorithm in 525p mode.The ADV7196A is a triple high-speed, digital-to- ..
ADV7197KS ,Multiformat HDTV Encoder with Three 11-Bit DACsGENERAL DESCRIPTIONcodes control the insertion of appropriate synchronization signalsThe ADV7197 is ..
AM27C64-90DI , 64 Kilobit (8 K x 8-Bit) CMOS EPROM
AM27H010 , 1 Megabit (131,072 x 8-bit) High Speed CMOS EPROM
AM27H010-45DC , 1 Megabit (131,072 x 8-bit) High Speed CMOS EPROM
AM27H010-45DI , 1 Megabit (131,072 x 8-bit) High Speed CMOS EPROM
AM27S03APC , 64-Bit Inverting-Output Bipolar RAM
AM27S03PC , 64-Bit Inverting-Output Bipolar RAM


ADV7192KST
Video Encoder with Six 10-Bit DACs, 54 MHz Oversampling and Progressive Scan Inputs
REV.0
Video Encoder with Six 10-Bit DACs, 54MHz
Oversampling and Progressive Scan Inputs
FEATURES
Six High-Quality 10-Bit Video DACs
10-Bit Internal Digital Video Processing
Multistandard Video Input
Multistandard Video Output
4� Oversampling with Internal 54MHz PLL
Programmable Video Control Includes:
Digital Noise Reduction
Gamma Correction
Black Burst
LUMA Delay
CHROMA Delay
Multiple Luma and Chroma Filters
Luma SSAF™ (Super Subalias Filter)
Average Brightness Detection
Field Counter
Macrovision Rev. 7.1
CGMS (Copy Generation Management System)
WSS (Wide Screen Signaling)
Closed Captioning Support.
Teletext Insertion Port (PAL-WST)
2-Wire Serial MPU Interface (I2C®-Compatible
and Fast I2C)2C Interface
Supply Voltage 5V and 3.3V Operation
80-Lead LQFP Package

SSAF is a trademark of Analog Devices Inc.
This device is protected by U.S. patent numbers 4631603, 4577216 and 4819098 and other intellectual property rights.
ITU-R and CCIR are used interchangeably in this document (ITU-R has replaced CCIR recommendations).2C is a registered trademark of Philips Corporation.
Throughout the document YUV refers to digital or analog component video.
APPLICATIONS
DVD Playback Systems
PC Video/Multimedia Playback Systems
Progressive Scan Playback Systems
GENERAL DESCRIPTION

The ADV7192 is part of the new generation of video encoders
from Analog Devices. The device builds on the performance of
previous video encoders and provides new features like interfac-
ing progressive scan devices, Digital Noise Reduction, Gamma
Correction, 4× Oversampling and 54MHz operation, Average
Brightness Detection, Black Burst Signal Generation, Chroma
Delay, an additional Chroma Filter, and other features.
The ADV7192 supports NTSC-M, NTSC-N (Japan), PAL N,
PAL M, PAL-B/D/G/H/I and PAL-60 standards. Input standards
supported include ITU-R.BT656 4:2:2 YCrCb in 8-Bit or 16-Bit
format and 3× 10-Bit YCrCb progressive scan format.
The ADV7192 can output Composite Video (CVBS), S-Video
(Y/C), Component YUV or RGB and analog progressive scan in
YPrPb format. The analog component output is also compatible
with Betacam, MII, and SMPTE/EBU N10 levels, SMPTE
170M NTSC, and ITU–R.BT 470 PAL.
Please see Detailed Description of Features for more informa-
tion about the ADV7192.
SIMPLIFIED FUNCTIONAL BLOCK DIAGRAM
ADV7192
CONTENTS

FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
APPLICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
GENERAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . 1
SIMPLIFIED FUNCTIONAL BLOCK DIAGRAM . . . . . . 1
SPECIFICATIONS
Static Performance 5 V . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Static Performance 3.3 V . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Dynamic Specifications 5 V . . . . . . . . . . . . . . . . . . . . . . . . 5
Dynamic Specifications 3.3 V . . . . . . . . . . . . . . . . . . . . . . . 5
Timing Characteristics 5 V . . . . . . . . . . . . . . . . . . . . . . . . 6
Timing Characteristics 3.3 V . . . . . . . . . . . . . . . . . . . . . . . 7
ABSOLUTE MAXIMUM RATINGS . . . . . . . . . . . . . . . . . 9
PIN CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
ORDERING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
PACKAGE THERMAL PERFORMANCE . . . . . . . . . . . . . 9
PIN FUNCTION DESCRIPTIONS . . . . . . . . . . . . . . . . . 10
DETAILED DESCRIPTION OF FEATURES . . . . . . . . . 11
GENERAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . .11
DATA PATH DESCRIPTION . . . . . . . . . . . . . . . . . . . . . 12
INTERNAL FILTER RESPONSE . . . . . . . . . . . . . . . . . . . 13
FEATURES: FUNCTIONAL DESCRIPTION . . . . . . . . . 17
BLACK BURST OUTPUT . . . . . . . . . . . . . . . . . . . . . . . . 17
BRIGHTNESS DETECT . . . . . . . . . . . . . . . . . . . . . . . . . . 17
CHROMA/LUMA DELAY . . . . . . . . . . . . . . . . . . . . . . . . 17
CLAMP OUTPUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
CSO, HSO AND VSO OUTPUTS . . . . . . . . . . . . . . . . . . . 17
COLOR BAR GENERATION . . . . . . . . . . . . . . . . . . . . . . 17
COLOR BURST SIGNAL CONTROL . . . . . . . . . . . . . . . 17
COLOR CONTROLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
CHROMINANCE CONTROL . . . . . . . . . . . . . . . . . . . . . 17
UNDERSHOOT LIMITER . . . . . . . . . . . . . . . . . . . . . . . . 18
DIGITAL NOISE REDUCTION . . . . . . . . . . . . . . . . . . . . 18
DOUBLE BUFFERING . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
GAMMA CORRECTION CONTROL . . . . . . . . . . . . . . . 18
NTSC PEDESTAL CONTROL . . . . . . . . . . . . . . . . . . . . . 18
POWER-ON RESET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
PROGRESSIVE SCAN INPUT . . . . . . . . . . . . . . . . . . . . . 18
REAL-TIME CONTROL, SUBCARRIER RESET, AND
TIMING RESET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
SCH PHASE MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
SLEEP MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
SQUARE PIXEL MODE . . . . . . . . . . . . . . . . . . . . . . . . . . 19
VERTICAL BLANKING DATA INSERTION
AND BLANK INPUT . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
YUV LEVELS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
16-BIT INTERFACE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
4× OVERSAMPLING AND INTERNAL PLL . . . . . . . . . 20
VIDEO TIMING DESCRIPTION . . . . . . . . . . . . . . . . . . . 20
MPU PORT DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . 28
REGISTER ACCESSES . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
REGISTER PROGRAMMING . . . . . . . . . . . . . . . . . . . . . 29
MODE REGISTERS 0–9 . . . . . . . . . . . . . . . . . . . . . . . 30–35
TIMING REGISTERS 0–17 . . . . . . . . . . . . . . . . . . . . . . .36
SUBCARRIER FREQUENCY AND
PHASE REGISTERS . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
CLOSED CAPTIONING REGISTERS . . . . . . . . . . . . . . . 37
NTSC PEDESTAL/PAL TELETEXT CONTROL
REGISTERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
TELETEXT CONTROL REGISTER . . . . . . . . . . . . . . . . 38
CGMS_WSS REGISTERS . . . . . . . . . . . . . . . . . . . . . . . . . 38
CONTRAST CONTROL REGISTERS . . . . . . . . . . . . . . . 39
HUE ADJUST CONTROL REGISTER (HCR) . . . . . . . . 40
HCR BIT DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . .40
BRIGHTNESS CONTROL REGISTER (BCR) . . . . . . . . 40
BCR BIT DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . .40
SHARPNESS RESPONSE REGISTER (PR) . . . . . . . . . . . 41
PR BIT DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . .41
DNR REGISTERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
DNR BIT DESCRIPTIONS . . . . . . . . . . . . . . . . . . . . . . . .41
GAMMA CORRECTION REGISTERS . . . . . . . . . . . . . . 43
BRIGHTNESS DETECT REGISTER . . . . . . . . . . . . . . . . 44
OUTPUT CLOCK REGISTER . . . . . . . . . . . . . . . . . . . . . 44
OCR BIT DESCRIPTIONS . . . . . . . . . . . . . . . . . . . . . . . .44
APPENDIX 1
Board Design and Layout Considerations . . . . . . . . . . . . 45
APPENDIX 2
Closed Captioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
APPENDIX 3
Copy Generation Management System (CGMS) . . . . . . . 48
APPENDIX 4
Wide Screen Signaling . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
APPENDIX 5
Teletext Insertion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
APPENDIX 6
Optional Output Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
APPENDIX 7
DAC Buffering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
APPENDIX 8
Recommended Register Values . . . . . . . . . . . . . . . . . . . . 53
APPENDIX 9
NTSC Waveforms (With Pedestal) . . . . . . . . . . . . . . . . . 57
NTSC Waveforms (Without Pedestal) . . . . . . . . . . . . . . . 58
PAL Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Video Measurement Plots . . . . . . . . . . . . . . . . . . . . . . . . 60
UV Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Output Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
APPENDIX 10
Vector Plots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
OUTLINE DIMENSIONS . . . . . . . . . . . . . . . . . . . . . . . . . 69
ADV7192
5 V SPECIFICATIONS1

DIGITAL INPUTS
VOLTAGE REFERENCE
POWER REQUIREMENTS
NOTESAll measurements are made in 4× Oversampling Mode unless otherwise specified.Temperature range TMIN to TMAX: 0°C to 70°C.Guaranteed by characterization.For all inputs but PAL_NTSC and ALSB.For PAL_NTSC and ALSB inputs.For all outputs but VSO/TTX/CLAMP.For VSO/TTX/CLAMP output.Measurement made in 2× Oversampling Mode.IDAC is the total current required to supply all DACs including the VREF Circuitry.All six DACs ON.ICCT or the circuit current, is the continuous current required to drive the digital core without IPLL.
Specifications subject to change without notice.
(VAA = 5 V, VREF = 1.235 V, RSET1,2 = 1200 � unless otherwise noted. All specifications TMIN to TMAX2
unless otherwise noted.)
SPECIFICATIONS
ADV7192–SPECIFICATIONS
3.3 V SPECIFICATIONS1

DIGITAL OUTPUTS
POWER REQUIREMENTS
NOTESAll measurements are made in 4× Oversampling Mode unless otherwise specified and are guaranteed by characterization. In 2× Oversampling Mode, power require-
ment for the ADV7192 is typically 3.0V.Temperature range TMIN to TMAX: 0°C to 70°C.For all inputs but PAL_NTSC and ALSB.For PAL_NTSC and ALSB inputs.For all outputs but VSO/TTX/CLAMP.For VSO/TTX/CLAMP output.Measurement made in 2× Oversampling Mode.IDAC is the total current required to supply all DACs including the VREF Circuitry.All six DACs ON.ICCT or the circuit current, is the continuous current required to drive the digital core without IPLL.
Specifications subject to change without notice.
(VAA = 3.3 V, VREF = 1.235 V, RSET1,2 = 1200 � unless otherwise noted. All specifications TMIN to TMAX2
unless otherwise noted.)
ADV7192
5 V DYNAMIC–SPECIFICATIONS1

NOTESAll measurements are made in 4× Oversampling Mode unless otherwise specified and are guaranteed by characterization.Temperature range TMIN to TMAX: 0°C to 70°C.Values in parentheses apply to 2× Oversampling Mode.
Specifications subject to change without notice.
3.3 V DYNAMIC–SPECIFICATIONS1

NOTESAll measurements are made in 4× Oversampling Mode unless otherwise specified and are guaranteed by characterization.Temperature range TMIN to TMAX: 0°C to 70°C.Values in parentheses apply to 2× Oversampling Mode.
Specifications subject to change without notice.
(VAA = 5 V � 250 mV, VREF = 1.235 V, RSET1,2 = 1200 � unless otherwise noted. All
specifications TMIN to TMAX2 unless otherwise noted.)
(VAA = 3.3 V � 150 mV, VREF = 1.235 V, RSET1,2 = 1200 � unless otherwise noted. All
specifications TMIN to TMAX2 unless otherwise noted.)
ADV7192
5 V TIMING CHARACTERISTICS

PLL
NOTESTemperature range TMIN to TMAX: 0°C to 70°C.Guaranteed by characterization.Pixel Port consists of:
Data: P7–P0, Y0/P8–Y7/P15 Pixel Inputs
Control: HSYNC, VSYNC, BLANK
Clock: CLKINTeletext Port consists of:
Digital Output: TTXRQ
Data: TTX
Specifications subject to change without notice.
(VAA = 5 V � 250mV, VREF = 1.235 V, RSET1,2 = 1200 V unless otherwise noted. All
specifications TMIN to TMAX1 unless otherwise noted.)
3.3 V TIMING CHARACTERISTICS
NOTESTemperature range TMIN to TMAX: 0°C to 70°C.Guaranteed by characterization.Pixel Port consists of:
Data: P7–P0, Y0/P8–Y7/P15 Pixel Inputs
Control: HSYNC, VSYNC, BLANK
Clock: CLKINTeletext Port consists of:
Digital Output: TTXRQ
Data: TTX
Specifications subject to change without notice.
(VAA = 3.3 V � 150 mV, VREF = 1.235 V, RSET1,2 = 1200 � unless otherwise noted. All
specifications TMIN to TMAX1 unless otherwise noted.)2
ADV7192
Figure 1.MPU Port Timing Diagram
Figure 2.Pixel and Control Data Timing Diagram
Figure 3.Teletext Timing Diagram
Figure 4.Progressive Scan Input Timing
ABSOLUTE MAXIMUM RATINGS1
VAA to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Voltage on any Digital Input Pin . . GND – 0.5 V to VAA + 0.5 V
Storage Temperature (TS) . . . . . . . . . . . . . . –65°C to +150°C
Junction Temperature (TJ) . . . . . . . . . . . . . . . . . . . . . . 150°C
Body Temperature (Soldering, 10 secs) . . . . . . . . . . . . . 220°C
Analog Outputs to GND2 . . . . . . . . . . . . GND – 0.5V to VAA
NOTESStresses above those listed under Absolute Maximum Ratings may cause perma-
nent damage to the device. This is a stress rating only; functional operation of the
device at these or any other conditions above those listed in the operational sections
of this specification is not implied. Exposure to absolute maximum rating condi-
tions for extended periods may affect device reliability.Analog Output Short Circuit to any Power Supply or Common can be of an
indefinite duration.
PACKAGE THERMAL PERFORMANCE

The 80-lead package is used for this device. The junction-to-
ambient (θJA) thermal resistance in still air on a four-layer PCB
is 24.7°C.
To reduce power consumption when using this part the user
can run the part on a 3.3 V supply, turn off any unused DACs.
The user must at all times stay below the maximum junction
temperature of 110°C. The following equation shows how to
calculate this junction temperature:
Junction Temperature = (VAA × (IDAC + ICCT)) × θJA + 70°C TAMB
IDAC = 10 mA + (sum of the average currents consumed by
each powered-on DAC)
Average current consumed by each powered-on DAC =
(VREF × K )/RSET
VREF = 1.235 V
K = 4.2146
ORDERING GUIDE
CAUTION

ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000V readily
PIN CONFIGURATION
NC = NO CONNECT
Y[0]/P8
Y[1]/P9
Y[2]/P10
Y[3]/P11
Y[4]/P12
Y[5]/P13
Y[6]/P14
Y[7]/P15
Y[8]
Y[9]
VREF
COMP 1
DAC A
DAC B
VAA
AGND
DAC C
DAC D
AGND
VAA
DAC E
DAC F
COMP 2
RSET2
DGND
RESET
PAL_NTSC
RSET1
ALSB
SCRESET/RTC/TR
DGND
HSYNC
VSYNC
BLANK
TTXREQ
DGND
AGND
SCL
SDA
CLKIN
CLKOUT
Cb[4]Cb[5]Cb[6]Cb[7]Cb[8]Cb[9]
DGNDV
Cb[3]DGNDVSO
TTX
/CLAMP
CSO_HSOCb[2]Cb[1]Cb[0]Cr[9]Cr[8]Cr[7]Cr[6]Cr[5]V
Cr[4]Cr[3]Cr[2]Cr[1]Cr[0]
ADV7192
PIN FUNCTION DESCRIPTIONS

19, 20
22, 33, 43, 69,
DETAILED DESCRIPTION OF FEATURES
Clocking:
Single 27 MHz Clock Required to Run the Device
4� Oversampling with Internal 54MHz PLL
Square Pixel Operation
Advanced Power Management
Programmable Video Control Features:
Digital Noise Reduction
Black Burst Signal Generation
Pedestal Level
Hue, Brightness, Contrast, and Saturation
Clamping Output Signal
VBI (Vertical Blanking Interval)
Subcarrier Frequency and Phase
LUMA Delay
CHROMA Delay
Gamma Correction
Luma And Chroma Filters
Luma SSAF (Super Subalias Filter)
Average Brightness Detection
Field Counter
Interlaced/Noninterlaced Operation
Complete On-Chip Video Timing Generator
Programmable Multimode Master/Slave Operation
Macrovision Rev 7.1
CGMS (Copy Generation Management System)
WSS (Wide Screen Signaling)
Closed Captioning Support
Teletext Insertion Port (PAL-WST)
2-Wire Serial MPU Interface2C-Compatible And Fast I2C)2C Registers Synchronized to VSYNC
GENERAL DESCRIPTION

The ADV7192 is an integrated Digital Video Encoder that
converts digital CCIR-601/656 4:2:2 8-bit or 16-bit component
video data into a standard analog baseband television signal
compatible with worldwide standards. Additionally, it is possible
Y0–Y9Cb0–Cb9Cr0–Cr9
DAC A
DAC B
DAC C
VREF
RSET2
COMP2
DAC D
DAC F
DAC E
ALSBSDASCLPAL_NTSCVSO/CLAMPCSO_HSO
HSYNC
VSYNCBLANK
RESET
TTX
TTXRQ
P15

to input video data in 3� 10-bit YCrCb progressive scan format
to facilitate interfacing devices such as progressive scan systems.
Six DACs are available on the ADV7192, each of which is capable
of providing 4.33mA of current. In addition to the composite
output signal there is the facility to output S-Video (Y/C Video),
RGB Video and YUV Video. All YUV formats (SMPTRE/EBU
N10, MII or Betacam) are supported.
The on-board SSAF (Super Subalias Filter) with extended lumi-
nance frequency response and sharp stopband attenuation
enables studio quality video playback on modern TVs, giving
optimal horizontal line resolution. An additional sharpness
control feature allows high-frequency enhancement on the
luminance signal.
Figure 6.Block Diagram for DNR Mode and DNR Sharpness
Mode
ADV7192
Digital Noise Reduction allows improved picture quality in remov-
ing low amplitude, high frequency noise. Figure 6 shows the DNR
functionality in the two modes available.
Programmable gamma correction is also available. The figure below
shows the response of different gamma values to a ramp signal.
GAMMA-CORRECTED AMPLITUDE50100150200250
LOCATION

Figure 7.Signal Input (Ramp) and Selectable Gamma
Output Curves
The device is driven by a 27MHz clock. Data can be output atMHz or 54MHz (on-board PLL) when 4� oversampling is
enabled. Also, the output filter requirements in 4� oversampling
and 2� oversampling differ, as can be seen in Figure 8.
Figure 8.Output Filter Requirements in 4×Oversampling
Mode
Figure 9.PLL and 4× Oversampling Block Diagram
The ADV7192 also supports both PAL and NTSC square pixel
operation. In this case the encoder requires a 24.5454MHz Clock
for NTSC or 29.5MHz Clock for PAL square pixel mode opera-
tion. All internal timing is generated on-chip.
The Output Video Frames are synchronized with the incoming
data Timing Reference Codes. Optionally, the Encoder accepts
(and can generate) HSYNC, VSYNC, and FIELD timing signals.
These timing signals can be adjusted to change pulsewidth and
position while the part is in master mode.
HSO/CSO and VSO TTL outputs are also available and are timed
to the analog output video.
A separate teletext port enables the user to directly input teletext
data during the vertical blanking interval.
The ADV7192 also incorporates WSS and CGMS-A data control
generation.
The ADV7192 modes are set up over a 2-wire serial bidirectional
port (I2C-compatible) with two slave addresses, and the device
is register-compatible with the ADV7172.
The ADV7192 is packaged in an 80-lead LQFP package.
DATA PATH DESCRIPTION

For PAL B, D, G, H, I, M, N, and NTSCM, N modes, YCrCb
4:2:2 data is input via the CCIR-656/601-compatible Pixel Port
at a 27 MHz Data Rate. The Pixel Data is demultiplexed to form
three data paths. Y typically has a range of 16 to 235, Cr and Cb
typically have a range of 128�112; however, it is possible to
input data from 1 to 254 on both Y, Cb, and Cr. The ADV7192
supports PAL (B, D, G, H, I, N, M) and NTSCM, N (with
and without Pedestal) and PAL60 standards.
Digital noise reduction can be applied to the Y signal. Pro-
grammable gamma correction can also be applied to the Y
signal if required.
The Y data can be manipulated for contrast control and a setup
level can be added for brightness control. The Cr, Cb data can
be scaled to achieve color saturation control. All settings become
effective at the start of the next field when double buffering is
enabled.
The appropriate sync, blank, and burst levels are added to the
YCrCb data. Macrovision antitaping, closed-captioning and
teletext levels are also added to Y and the resultant data is inter-
polated to 54 MHz (4� Oversampling Mode). The interpolated
data is filtered and scaled by three digital FIR filters.
The U and V signals are modulated by the appropriate Subcarrier
Sine/Cosine waveforms and a phase offset may be added onto
the color subcarrier during active video to allow hue adjustment.
The resulting U and V signals are added together to make up
the Chrominance signal. The Luma (Y) signal can be delayed
by up to six clock cycles (at 27 MHz) and the Chroma signal
can be delayed by up to eight clock cycles (at 27 MHz).
The Luma and Chroma signals are added together to make up
the Composite Video Signal. All timing signals are controlled.
The YCrCb data is also used to generate RGB data with appropri-
ate sync and blank levels. The YUV levels are scaled to output
the suitable SMPTE/EBU N10, MII, or Betacam levels.
Each DAC can be individually powered off if not required. A
complete description of DAC output configurations is given in
the Mode Register 2 section.
Table I.Luminance Internal Filter Specifications (4� Oversampling)
Low-Pass (NTSC)
Low-Pass (PAL)
Notch (NTSC)
Notch (PAL)
Extended (SSAF)
CIF
NOTESPassband Ripple is defined as the fluctuations from the 0 dB response in the passband, measured in (dB). The passband is defined to have 0–fc frequency limits for a
low-pass filter, 0–f1 and f2–infinity for a notch filter, where fc, f1, f2 are the –3 dB points.3 dB bandwidth refers to the –3 dB cutoff frequency.Stopband Cutoff refers to the frequency at the attenuation point referred to under Note 4.Stopband Attenuation refers to the attenuation point (dB) at the frequency referred to under Note 3.
Table II.Chrominance Internal Filter Specifications (4� Oversampling)

1.3 MHz Low-Pass
0.65 MHz Low-Pass
1.0 MHz Low-Pass
2.0 MHz Low-Pass
3.0 MHz Low-Pass
CIF
NOTES
1Passband Ripple is defined as the fluctuations from the 0 dB response in the passband, measured in (dB). The passband is defined to have 0–fc frequency limits for a
low-pass filter, 0–f1 and f2–infinity for a notch filter, where fc, f1, f2 are the –3 dB points.
23 dB bandwidth refers to the –3 dB cutoff frequency.
3Stopband Cutoff refers to the frequency at the attenuation point referred to under Note 4.
4Stopband Attenuation refers to the attenuation point (dB) at the frequency referred to under Note 3.
When used to interface progressive scan systems, the ADV7192
allows input to YCrCb signals in Progressive Scan format
(3� 10-bit) before these signals are routed to the interpolation
filters and the DACs.
INTERNAL FILTER RESPONSE

The Y Filter supports several different frequency responses
including two low-pass responses, two notch responses, an
Extended (SSAF) response with or without gain boost/attenuation,
a CIF response, and a QCIF response. The UV/filter supports
several different frequency responses including five low-pass
responses, a CIF response, and a QCIF response, as can be seen in
the following figures. All filter plots show the 4� Oversampling
responses.
In Extended Mode there is the option of 12 responses in the range
from –4 dB to +4 dB. The desired response can be chosen by the
user by programming the correct value via the I2C. The variation
of frequency responses can be seen in the Tables I and II. For
more detailed filter plots refer to Analog Devices’ Application
Note AN-562.
ADV7192
FREQUENCY – MHz
MAGNITUDE
dB

Figure 10.NTSC Low-Pass Luma Filter
FREQUENCY – MHz
MAGNITUDE
dB

Figure 11.PAL Low-Pass Luma Filter
MAGNITUDE
dB
FREQUENCY – MHz

Figure 12.NTSC Notch Luma Filter
MAGNITUDE
dB
FREQUENCY – MHz

Figure 13.PAL Notch Luma Filter
MAGNITUDE
dB
FREQUENCY – MHz

Figure 14.Extended Mode (SSAF) Luma Filter26735–12
MAGNITUDE
dB
FREQUENCY – MHz
–10

Figure 15.Extended SSAF Luma Filter and Programmable
Gain/Attenuation Showing +4 dB/–12dB Range
26735–5MAGNITUDE
dB
FREQUENCY – MHz

Figure 16.Extended SSAF and Programmable Attenuation,
Showing Range 0 dB/–4dB26735–1
MAGNITUDE
dB
FREQUENCY – MHz

Figure 17.Extended SSAF and Programmable Gain,
Showing Range 0 dB/+4dB
MAGNITUDE
dB
FREQUENCY – MHz

Figure 18.Luma CIF Filter
Figure 19.Luma QCIF Filter
Figure 20.Chroma 0.65MHz Low-Pass Filter
Figure 21.Chroma 1.0MHz Low-Pass Filter
ADV7192
MAGNITUDE
dB
FREQUENCY – MHz

Figure 22.Chroma 1.3MHz Low-Pass Filter
Figure 23.Chroma 2MHz Low-Pass Filter
MAGNITUDE
dB
FREQUENCY – MHz

Figure 24.Chroma 3MHz Low-Pass Filter
MAGNITUDE
dB
FREQUENCY – MHz

Figure 25.Chroma CIF Filter
MAGNITUDE
dB
FREQUENCY – MHz

Figure 26.Chroma QCIF Filter
FEATURES: FUNCTIONAL DESCRIPTION
BLACK BURST OUTPUT

It is possible to output a black burst signal from two DACs. This
signal output is very useful for professional video equipment
since it enables two video sources to be locked together. (Mode
Register 9.)
Figure 27.Possible Application for the Black Burst Output
Signal
BRIGHTNESS DETECT

This feature is used to monitor the average brightness of the
incoming Y video signal on a field by field basis. The information
is read from the I2C and based on this information the color
saturation, contrast and brightness controls can be adjusted (for
example to compensate for very dark pictures). (Brightness Detect
Register.)
CHROMA/LUMA DELAY

The luminance data can be delayed by maximum of six clock
cycles. Additionally the Chroma can be delayed by a maximum
of eight clock cycles (one clock cycle at 27 MHz). (Timing Reg-
ister 0 and Mode Register 9.)
Figure 28.Chroma Delay Figure 29.Luma Delay
CLAMP OUTPUT

The ADV7192 has a programmable clamp TTL output signal.
This clamp signal is programmable to the front and back porch.
The clamp signal can be varied by one to three clock cycles in a
positive and negative direction from the default position.
(Mode Register 5, Mode Register 7.)
CSO, HSO AND VSO OUTPUTS

The ADV7192 supports three output timing signals, CSO
(composite sync signal), HSO (Horizontal Sync Signal) and
VSO (Vertical Sync Signal). These output TTL signals are aligned
with the analog video outputs. See Figure 31 for an example
of these waveforms. (Mode Register 7.)
Figure 31.CSO, HSO, VSO Timing Diagram
COLOR BAR GENERATION

The ADV7192 can be configured to generate 100/7.5/75/7.5 color
bars for NTSC or 100/0/75/0 color bars for PAL.
(Mode Register 4.)
COLOR BURST SIGNAL CONTROL

The burst information can be switched on and off the composite
and chroma video output. (Mode Register 4.)
COLOR CONTROLS

The ADV7192 allows the user to control the brightness, contrast,
hue and saturation of the color. The control registers may be
double-buffered, meaning that any modification to the registers
will be done outside the active video region and, therefore, changes
made will not be visible during active video.
Contrast Control

Contrast adjustment is achieved by scaling the Y input data by a
factor programmed by the user. This factor allows the data to be
scaled between 0% and 150%. (Contrast Control Register.)
Brightness Control

The brightness is controlled by adding a programmable setup level
onto the scaled Y data. This brightness level may be added onto
the Y data. For NTSC with pedestal, the setup can vary from
0 IRE to 22.5 IRE. For NTSC without pedestal and PAL, the
setup can vary from –7.5 IRE to +15 IRE. (Brightness Control
Register.)
Color Saturation

Color adjustment is achieved by scaling the Cr and Cb input
data by a factor programmed by the user. This factor allows the
data to be scaled between 0% and 200%. (U Scale Register and
V Scale Register.)
Hue Adjust Control

The hue adjustment is achieved on the composite and chroma
outputs by adding a phase offset onto the color subcarrier in the
active video but leaving the color burst unmodified, i.e., only
the phase between the video and the colorburst is modified and
hence the hue is shifted. The ADV7192 provides a range of
±22° in increments of 0.17578125°. (Hue Adjust Register.)
CHROMINANCE CONTROL
ADV7192
UNDERSHOOT LIMITER

A limiter is placed after the digital filters. This prevents any
synchronization problems for TVs. The level of undershoot is
programmable between –1.5 IRE, –6 IRE, –11 IRE when oper-
ating in 4× Oversampling Mode. In 2× Oversampling Mode the
limits are –7.5 IRE and 0 IRE. (Mode Register 9 and Timing
Register 0.)
DIGITAL NOISE REDUCTION

DNR is applied to the Y data only. A filter block selects the
high frequency, low amplitude components of the incoming
signal (DNR Input Select). The absolute value of the filter output
is compared to a programmable threshold value (DNR Thresh-
old Control). There are two DNR modes available: DNR Mode
and DNR Sharpness Mode.
In DNR Mode, if the absolute value of the filter output is smaller
than the threshold, it is assumed to be noise. A programmable
amount (Coring Gain Control) of this noise signal will be sub-
tracted from the original signal.
In DNR Sharpness Mode, if the absolute value of the filter output
is less than the programmed threshold, it is assumed to be noise,
as before. Otherwise, if the level exceeds the threshold, now
being identified as a valid signal, a fraction of the signal (Coring
Gain Control) will be added to the original signal in order to boost
high frequency components and to sharpen the video image.
In MPEG systems it is common to process the video information
in blocks of 8 × 8 pixels for MPEG2 systems, or 16 × 16 pixels
for MPEG1 systems ('Block Size Control'). DNR can be applied
to the resulting block transition areas that are known to contain
noise. Generally the block transition area contains two pixels. It
is possible to define this area to contain four pixels (Border Area
Control).
It is also possible to compensate for variable block positioning or
differences in YCrCb pixel timing with the use of the Block Offset
Control. (Mode Register 8, DNR Registers 0–2.)
DOUBLE BUFFERING

Double buffering can be enabled or disabled on the following
registers: Closed Captioning Registers, Brightness Control Reg-
ister, V-Scale, U-Scale Contrast Control Register, Hue Adjust
Register, Macrovision Registers, and the Gamma Curve Select
bit. These registers are updated once per field on the falling
edge of the VSYNC signal. Double Buffering improves the overall
performance of the ADV7192, since modifications to register
settings will not be made during active video, but take effect on
the start of the active video. (Mode Register 8.)
GAMMA CORRECTION CONTROL

Gamma correction may be performed on the luma data. The
user has the choice to use either of two different gamma curves,
A or B. At any one time one of these curves is operational if
gamma correction is enabled. Gamma correction allows the
mapping of the luma data to a user-defined function. (Mode
Register 8, Gamma Correction Registers 0–13.)
NTSC PEDESTAL CONTROL

In NTSC mode it is possible to have the pedestal signal gener-
POWER-ON RESET

After power-up, it is necessary to execute a RESET operation. A
reset occurs on the falling edge of a high-to-low transition on the
RESET pin. This initializes the pixel port such that the data on
the pixel inputs pins is ignored. See Appendix 8 for the register
settings after RESET is applied.
PROGRESSIVE SCAN INPUT

It is possible to input data to the ADV7192 in progressive scan
format. For this purpose the input pins Y0/P8–Y7/P15, Y8–Y9,
Cr0–Cr9 and Cb0–Cb9 accept 10-bit Y data, 10-bit Cb data
and 10-bit Cr data. The data is clocked into the part at 27 MHz.
The data is then filtered and sinc corrected in an 2� Interpo-
lation filter and then output to three video DACs at 54 MHz
(to interface to a progressive scan monitor).
FREQUENCY – MHz
AMPLITUDE
dB152025
–70

Figure 32. Plot of the Interpolation Filter for the Y Data
Figure 33.Plot of the Interpolation Filter for the CrCb Data
It is assumed that there is no color space conversion or any other
such operation to be performed on the incoming data. Thus if
these DAC outputs are to drive a TV, all relevant timing and
synchronization data should be contained in the incoming digital
Y data.
The block diagram below shows a possible configuration for
progressive scan mode using the ADV7192.
Figure 34.Block Diagram Using the ADV7192 in Progres-
sive Scan Mode
The progressive scan decoder deinterlaces the data from the
MPEG2 decoder. This now means that there are 525 video lines
per field in NTSC mode and 625 video lines per field in PAL
mode. The duration of the video line is now 32 µs.
It is important to note that the data from the MPEG2 decoder
is in 4:2:2 format. The data output from the progressive scan
decoder is in 4:4:4 format. Thus it is assumed that some form of
interpolation on the color component data is performed in the
progressive scan decoder IC. (Mode Register 8.)
REAL-TIME CONTROL, SUBCARRIER RESET, AND
TIMING RESET

Together with the SCRESET/RTC/TR pin and Mode Register 4
(Genlock Control), the ADV7192 can be used in (a) Timing
Reset Mode, (b) Subcarrier Phase Reset Mode or (c) RTC Mode.
(a)A TIMING RESET is achieved in holding this pin high. In
this state the horizontal and vertical counters will remain reset.
On releasing this pin (set to low), the internal counters will
commence counting again. The minimum time the pin has
to be held high is 37 ns (1 clock cycle at 27 MHz), otherwise
the reset signal might not be recognized.
(b)The SUBCARRIER PHASE will reset to that of Field 0 at
the start of the following field when a low to high transition
occurs on this input pin.
(c)In RTC MODE, the ADV7192 can be used to lock to an ex-
ternal video source.
The real-time control mode allows the ADV7192 to auto-
matically alter the subcarrier frequency to compensate for line
length variations. When the part is connected to a device
that outputs a digital datastream in the RTC format (such as
a ADV7185 video decoder, see Figure 38), the part will
automatically change to the compensated subcarrier frequency
on a line-by-line basis. This digital datastream is 67 bits
wide and the subcarrier is contained in Bits 0 to 21. Each bit
is two clock cycles long. 00Hex should be written into all four
Subcarrier Frequency registers when using this mode. (Mode
Register 4.)
SCH PHASE MODE

The SCH phase is configured in default mode to reset every
four (NTSC) or eight (PAL) fields to avoid an accumulation of
Resetting the SCH phase every four or eight fields avoids the
accumulation of SCH phase error, and results in very minor SCH
phase jumps at the start of the four or eight field sequence.
Resetting the SCH phase should not be done if the video source
does not have stable timing or the ADV7192 is configured in RTC
mode. Under these conditions (unstable video) the Subcarrier
Phase Reset should be enabled but no reset applied. In this
configuration the SCH Phase will never be reset; this means that
the output video will now track the unstable input video. The Sub-
carrier Phase Reset when applied will reset the SCH phase to Field
0 at the start of the next field (e.g., Subcarrier Phase Reset applied
in Field 5 (PAL) on the start of the next field SCH phase will be
reset to Field 0). (Mode Register 4.)
SLEEP MODE

If, after RESET, the SCRESET/RTC/TR and NTSC_PAL pins
are both set high, the ADV7192 will power up in Sleep Mode to
facilitate low power consumption before all registers have been
initialized.
If Power-up in Sleep Mode is disabled, Sleep Mode control
passes to the Sleep Mode control in Mode Register 2 (i.e., con-
trol via I2C). (Mode Register 2 and Mode Register 6.)
SQUARE PIXEL MODE

The ADV7192 can be used to operate in square pixel mode. For
NTSC operation an input clock of 24.5454 MHz is required.
Alternatively, for PAL operation, an input clock of 29.5 MHz
is required. The internal timing logic adjusts accordingly for
square pixel mode operation. Square pixel mode is not available
in 4× Oversampling mode. (Mode Register 2.)
VERTICAL BLANKING DATA INSERTION AND BLANK
INPUT

It is possible to allow encoding of incoming YCbCr data on
those lines of VBI that do not have line sync or pre-/post-equal-
ization pulses . This mode of operation is called Partial Blanking. It
allows the insertion of any VBI data (Opened VBI) into the
encoded output waveform, this data is present in digitized
incoming YCbCr data stream (e.g., WSS data, CGMS, VPS
etc.). Alternatively the entire VBI may be blanked (no VBI data
inserted) on these lines. VBI is available in all timing modes.
The complete VBI is comprised of the following lines:
525/60 systems, Lines 525 to 21 for field one and Lines 262 to
Line 284 for field two.
625/50 systems, Lines 624 to Line 22 and Lines 311 to 335.
The “Opened VBI” consists of:
525/60 systems, Lines 10 to 21 for field one and second half of
Line 273 to Line 284 for field two.
625/50 systems, Lines 7 to 22 and Lines 319 to 335.
(Mode Register 3.)
It is possible to allow control over the BLANK signal using
Timing Register 0. When the BLANK input is enabled (TR03 =
0 and input pin tied low), the BLANK input can be used to
input externally generated blank signals in Slave Mode 1, 2, or
3. When the BLANK input is disabled (TR03 = 1 and input pin
ADV7192
YUV LEVELS

This functionality allows the ADV7192 to output SMPTE levels
or Betacam levels on the Y output when configured in PAL or
NTSC mode.
SyncVideo

Betacam286 mV714 mV
SMPTE300 mV700 mV
MII300 mV700 mV
As the data path is branched at the output of the filters, the luma
signal relating to the CVBS or S-Video Y/C output is unaltered.
Only the Y output of the YCrCb outputs is scaled. This control
allows color component levels to have a peak-peak amplitude of
700 mV, 1000 mV or the default values of 934 mV in NTSC and
700 mV in PAL. (Mode Register 5.)
16-BIT INTERFACE

It is possible to input data in 16-bit format. In this case, the
interface only operates if the data is accompanied by separate
HSYNC/VSYNC/BLANK signals. Sixteen-bit mode is not
available in Slave Mode 0 since EAV/SAV timing codes are
used. (Mode Register 8.)
4� OVERSAMPLING AND INTERNAL PLL

It is possible to operate all six DACs at 27 MHz (2× Oversam-
pling) or 54 MHz (4× Oversampling).
The ADV7192 is supplied with a 27 MHz clock synced with the
incoming data. Two options are available: to run the device
throughout at 27 MHz or to enable the PLL. In the latter case,
even if the incoming data runs at 27 MHz, 4× Oversampling and
the internal PLL will output the data at 54 MHz.
NOTE
In 4× Oversampling Mode the requirements for the optional
output filters are different from those in 2× Oversampling. (Mode
Register 1, Mode Register 6.) See Appendix 6.
Figure 35.PLL and 4× Oversampling Block Diagram
Figure 36.Output Filter Requirements in 2× and 4× Over-
sampling Mode
VIDEO TIMING DESCRIPTION

The ADV7192 is intended to interface to off-the-shelf MPEG1
and MPEG2 Decoders. As a consequence, the ADV7192 accepts
4:2:2 YCrCb Pixel Data via a CCIR-656 Pixel Port and has
several Video Timing Modes of operation that allow it to be
configured as either System Master Video Timing Generator or
a Slave to the System Video Timing Generator. The ADV7192
generates all of the required horizontal and vertical timing periods
and levels for the analog video outputs.
The ADV7192 calculates the width and placement of analog
sync pulses, blanking levels, and color burst envelopes. Color
bursts are disabled on appropriate lines and serration and equal-
ization pulses are inserted where required.
In addition the ADV7192 supports a PAL or NTSC square pixel
operation. The part requires an input pixel clock of 24.5454 MHz
for NTSC square pixel operation and an input pixel clock of
29.5MHz for PAL square pixel operation. The internal horizontal
line counters place the various video waveform sections in the cor-
rect location for the new clock frequencies.
The ADV7192 has four distinct Master and four distinct Slave
timing configurations. Timing Control is established with
the bidirectional HSYNC, BLANK and VSYNC pins. Tim-
ing Register 1 can also be used to vary the timing pulsewidths
and where they occur in relation to each other. (Mode Regis-
ter 2, Timing Register 0, 1.)
RESET SEQUENCE

When RESET becomes active the ADV7192 reverts to the default
output configuration (see Appendix 8 for register settings). The
ADV7192 internal timing is under the control of the logic level
on the NTSC_PAL pin.
When RESET is released Y, Cr, Cb values corresponding to a
black screen are input to the ADV7192. Output timing signals
are still suppressed at this stage. DACs A, B, C are switched off
and DACs D, E, F are switched on.
When the user requires valid data, Pixel Data Valid Control is
enabled (MR26 = 1) to allow the valid pixel data to pass through
the encoder. Digital output timing signals become active and the
encoder timing is now under the control of the Timing Regis-
ters. If at this stage, the user wishes to select a different video
standard to that on the NTSC_PAL pin, Standard I2C Control
should be enabled (MR25 = 1) and the video standard required
is selected by programming Mode Register 0 (Output Video Stan-
dard Selection). Figure 37 illustrates the RESET sequence timing.
Figure 37.RESET Sequence Timing Diagram
Figure 38.RTC Timing and Connections
ADV7192
Mode 0 (CCIR–656):Slave Option

(Timing Register 0 TR0 = X X X X X 0 0 0)
The ADV7192 is controlled by the SAV (Start Active Video) and EAV (End Active Video) Time Codes in the Pixel Data. All timing
information is transmitted using a 4-byte Synchronization Pattern. A synchronization pattern is sent immediately before and after each line
during active picture and retrace. Mode 0 is illustrated in Figure 39. The HSYNC, VSYNC and BLANK (if not used) pins should be
tied high during this mode. Blank output is available.
Figure 39.Timing Mode 0, Slave Mode
Mode 0 (CCIR–656):Master Option

(Timing Register 0 TR0 = X X X X X 0 0 1)
The ADV7192 generates H, V, and F signals required for the SAV (Start Active Video) and EAV (End Active Video)
Time Codes in the CCIR656 standard. The H bit is output on the HSYNC pin, the V bit is output on the BLANK pin and the
F bit is output on the VSYNC pin. Mode 0 is illustrated in Figure 40 (NTSC) and Figure 41 (PAL). The H, V, and F transitions relative
to the video waveform are illustrated in Figure 42.
Figure 40.Timing Mode 0, NTSC Master Mode
Figure 41.Timing Mode 0, PAL Master Mode
Figure 42.Timing Mode 0 Data Transitions, Master Mode
ADV7192
Mode 1:Slave Option HSYNC, BLANK, FIELD

(Timing Register 0 TR0 = X X X X X 0 1 0)
In this mode the ADV7192 accepts Horizontal SYNC and Odd/ Even FIELD signals. A transition of the FIELD
input when HSYNC is low indicates a new frame, i.e., Vertical Retrace. The BLANK signal is optional. When the BLANK input is
disabled the ADV7192 automatically blanks all normally blank lines as per CCIR-624. Mode 1 is illustrated in Figure 43
(NTSC) and Figure 44 (PAL).
Figure 43.Timing Mode 1, NTSC
Figure 44.Timing Mode 1, PAL
Mode 1:Master Option HSYNC, BLANK, FIELD
(Timing Register 0 TR0 = X X X X X 0 1 1)
In this mode the ADV7192 can generate Horizontal SYNC and Odd/Even FIELD signals. A transition of the FIELD input when
HSYNC is low indicates a new frame i.e., Vertical Retrace. The BLANK signal is optional. When the BLANK input is disabled the
ADV7192 automatically blanks all normally blank lines as per CCIR-624. Pixel data is latched on the rising clock edge following the
timing signal transitions. Mode 1 is illustrated in Figure 43 (NTSC) and Figure 44 (PAL). Figure 45 illustrates the HSYNC, BLANK and
FIELD for an odd or even field transition relative to the pixel data.
Figure 45.Timing Mode 1 Odd/Even Field Transitions Master/Slave
Mode 2:Slave Option HSYNC, VSYNC, BLANK

(Timing Register 0 TR0 = X X X X X 1 0 0)
In this mode the ADV7192 accepts Horizontal and Vertical SYNC signals. A coincident low transition of both HSYNC and VSYNC
inputs indicates the start of an Odd Field. A VSYNC low transition when HSYNC is high indicates the start of an Even Field.
The BLANK signal is optional. When the BLANK input is disabled the ADV7192 automatically blanks all normally blank lines
as per CCIR-624. Mode 2 is illustrated in Figure 46 (NTSC) and Figure 47 (PAL).
Figure 46.Timing Mode 2, NTSC
ADV7192
Figure 47.Timing Mode 2, PAL
Mode 2:Master Option HSYNC, VSYNC, BLANK

(Timing Register 0 TR0 = X X X X X 1 0 1)
In this mode the ADV7192 can generate Horizontal and Vertical SYNC signals. A coincident low transition of both HSYNC and
VSYNC inputs indicates the start of an Odd Field. A VSYNC low transition when HSYNC is high indicates the start of an Even
Field. The BLANK signal is optional. When the BLANK input is disabled the ADV7192 automatically blanks all normally blank lines as
per CCIR-624. Mode 2 is illustrated in Figure 46 (NTSC) and Figure 47 (PAL). Figure 48 illustrates the HSYNC, BLANK and
VSYNC for an even-to-odd field transition relative to the pixel data. Figure 49 illustrates the HSYNC, BLANK and VSYNC for
an odd-to-even field transition relative to the pixel data.
Figure 48.Timing Mode 2, Even-to-Odd Field Transition Master/Slave
Mode 3:Master/Slave Option HSYNC, BLANK, FIELD
(Timing Register 0 TR0 = X X X X X 1 1 0 or X X X X X 1 1 1)
In this mode the ADV7192 accepts or generates Horizontal SYNC and Odd/Even FIELD signals. A transition of the FIELD input when
HSYNC is high indicates a new frame i.e., Vertical Retrace. The BLANK signal is optional. When the BLANK input is disabled the
ADV7192 automatically blanks all normally blank lines as per CCIR-624. Mode 3 is illustrated in Figure 50 (NTSC) and
Figure 51 (PAL).
Figure 50.Timing Mode 3, NTSC
Figure 51.Timing Mode 3, PAL
ADV7192
MPU PORT DESCRIPTION

The ADV7192 support a two-wire serial (I2C-compatible)
microprocessor bus driving multiple peripherals. Two inputs,
Serial Data (SDA) and Serial Clock (SCL), carry information
between any device connected to the bus. Each slave device is
recognized by a unique address. The ADV7192 has four possible
slave addresses for both read and write operations. These are
unique addresses for each device and are illustrated in Figure 52
and Figure 54. The LSB sets either a read or write operation.
Logic Level 1 corresponds to a read operation while Logic Level
0 corresponds to a write operation. A1 is set by setting the ALSB
pin of the ADV7192 to Logic Level 0 or Logic Level 1. When
ALSB is set to 0, there is greater input bandwidth on the I2C
lines, which allows high speed data transfers on this bus. When
ALSB is set to 1, there is reduced input bandwidth on the I2C
lines, which means that pulses of less than 50 ns will not pass
into the I2C internal controller. This mode is recommended for
noisy systems.
Figure 52.Slave Address
To control the various devices on the bus the following protocol
must be followed. First, the master initiates a data transfer by
establishing a start condition, defined by a high-to-low transition
on SDA while SCL remains high. This indicates that an address/
data stream will follow. All peripherals respond to the start con-
dition and shift the next eight bits (7-bit address + R/W bit). The
bits are transferred from MSB down to LSB. The peripheral that
recognizes the transmitted address responds by pulling the data
line low during the ninth clock pulse. This is known as an acknowl-
edge bit. All other devices withdraw from the bus at this point
and maintain an idle condition. The idle condition is where
the device monitors the SDA and SCL lines waiting for the
start condition and the correct transmitted address. The R/W bit
determines the direction of the data.
A Logic 0 on the LSB of the first byte means that the master
will write information to the peripheral. A Logic 1 on the LSB
of the first byte means that the master will read information
from the peripheral.
The ADV7192 acts as a standard slave device on the bus. The
data on the SDA pin is eight bits long supporting the 7-bit
addresses plus the R/W bit. It interprets the first byte as the device
address and the second byte as the starting subaddress. The
subaddresses autoincrement allowing data to be written to or read
from the starting subaddress. A data transfer is always terminated
by a stop condition. The user can also access any unique subaddress
register on a one-by-one basis without having to update all the
registers. There is one exception. The Subcarrier Frequency
Registers should be updated in sequence, starting with Subcarrier
Frequency Register 0. The autoincrement function should be
then used to increment and access Subcarrier Frequency Registers
1, 2, and 3. The Subcarrier Frequency Registers should not be
accessed independently.
Stop and start conditions can be detected at any stage during
the data transfer. If these conditions are asserted out of sequence
with normal read and write operations, then, these cause an
immediate jump to the idle condition. During a given SCL high
period the user should issue only one start condition, one stop
condition, or a single stop condition followed by a single start
condition. If an invalid subaddress is issued by the user, the
ADV7192 will not issue an acknowledge and will return to the
idle condition. If, in autoincrement mode, the user exceeds the
highest subaddress, then the following action will be taken:In Read Mode, the highest subaddress register contents
will continue to be output until the master device issues
a no-acknowledge. This indicates the end of a read. A
no-acknowledge condition is where the SDA line is not pulled
low on the ninth pulse.In Write Mode, the data for the invalid byte will be not be
loaded into any subaddress register, a no-acknowledge will
be issued by the ADV7192 and the part will return to the
idle condition.
Figure 53.Bus Data Transfer
Figure 53 illustrates an example of data transfer for a read
sequence and the start and stop conditions.
Figure 54 shows bus write and read sequences.
REGISTER ACCESSES
The MPU can write to or read from all of the registers of the
ADV7192 with the exception of the Subaddress Registers which
are write only registers. The Subaddress Register determines
which register the next read or write operation accesses. All com-
munications with the part through the bus start with an access
to the Subaddress Register. Then a read/write operation is per-
formed from/to the target address which then increments to
the next address until a stop command on the bus is performed.
REGISTER PROGRAMMING

The following section describes each register. All registers can
be read from as well as written to.
Subaddress Register (SR7–SR0)

The Communications Register is an eight bit write-only register.
After the part has been accessed over the bus and a read/write
operation is selected, the subaddress is set up. The Subaddress
Register determines to/from which register the operation takes
place.
Figure 55 shows the various operations under the control of the
Subaddress Register 0 should always be written to SR7.
Register Select (SR6–SR0)

These bits are set up to point to the required starting address.
ADV7192
MODE REGISTER 0
MR0 (MR07–MR00)
(Address (SR4–SR0) = 00H)

Figure 56 shows the various operations under the control of
Mode Register 0.
MR0 BIT DESCRIPTION
Output Video Standard Selection Control (MR00–MR01)

These bits are used to set up the encoder mode. The ADV7192
can be set up to output NTSC, PAL (B, D, G, H, I), PAL M or
PAL N standard video.
Luminance Filter Select (MR02–MR04)

These bits specify which luma filter is to be selected. The filter
selection is made independent of whether PAL or NTSC is
selected.
Chrominance Filter Select (MR05–MR07)

These bits select the chrominance filter. A low-pass filter can be
selected with a choice of cutoff frequencies (0.65 MHz, 1.0 MHz,
1.3 MHz, 2 MHz, or 3 MHz) along with a choice of CIF or
QCIF filters.
MODE REGISTER 1
MR1 (MR17–MR10)
(Address (SR4–SR0) = 01H)

Figure 57 shows the various operations under the control of
Mode Register 1.
MR1 BIT DESCRIPTION
DAC Control (MR10–MR15)

Bits MR15–MR10 can be used to power-down the DACs. This are
used to reduce the power consumption of the ADV7192 or if any
of the DACs are not required in the application.
4� Oversampling Control (MR16)

To enable 4× Oversampling this bit has to be set to 1. When
enabled, the data is output at a frequency of 54 MHz.
Note that PLL Enable Control has to be enabled (MR61 = 0) in
4× Oversampling mode. An external VREF is not recommended
in that mode.
Reserved (MR17)

A Logical 0 must be written to this bit.
Figure 56.Mode Register 0, MR0
Figure 57.Mode Register 1, MR1
MODE REGISTER 2
MR2 (MR27–MR20)
(Address (SR4–SR0) = 02H)

Mode Register 2 is an 8-bit-wide register.
Figure 58 shows the various operations under the control of Mode
Register 2.
MR2 BIT DESCRIPTION—RGB/YUV Control (MR20)

This bit enables the output from the DACs to be set to YUV or
RGB output video standard.
DAC Output Control (MR21)

This bit controls the output from DACs A, B, and C. When this
bit is set to 1, Composite, Luma and Chroma Signals are output
from DACs A, B, and C (respectively). When this bit is set to 0,
RGB or YUV may be output from these DACs.
SCART Enable Control (MR22)

This bit is used to switch the DAC outputs from SCART to a
EUROSCART configuration. A complete table of all DAC out-
put configurations is shown below.
Pedestal Control (MR23)

This bit specifies whether a pedestal is to be generated on the
NTSC composite video signal. This bit is invalid when the device
is configured in PAL mode.
Square Pixel Control (MR24)

This bit is used to set up square pixel mode. This is available in
Slave Mode only. For NTSC, a 24.54 MHz clock must be sup-
plied. For PAL, a 29.5 MHz clock must be supplied. Square
pixel operation is not available in 4× Oversampling mode.
Standard I2C Control (MR25)

This bit controls the video standard used by the ADV7192.
When this bit is set to 1 the video standard is as programmed in
Mode Register 0 (Output Video Standard Selection). When it is
set to 0, the ADV7192 is forced into the standard selected by
the NTSC_PAL pin. When NTSC_PAL is low, the standard is
NTSC, when the NTSC_PAL pin is high, the standard is PAL.
Pixel Data Valid Control (MR26)

After resetting the device this bit has the value 0 and the pixel
data input to the encoder is blanked such that a black screen is
output from the DACs. The ADV7192 will be set to Master Mode
timing. When this bit is set to 1 by the user (via the I2C), pixel
data passes to the pins and the encoder reverts to the timing mode
defined by Timing Register 0.
Sleep Mode Control (MR27)

When this bit is set (1), Sleep Mode is enabled. With this mode
enabled, the ADV7192 current consumption is reduced to typi-
cally 0.1 µA. The I2C registers can be written to and read from
when the ADV7192 is in Sleep Mode.
When the device is in Sleep Mode and 0 is written to MR27, the
ADV7192 will come out of Sleep Mode and resume normal
operation. Also, if a RESET is applied during Sleep Mode the
ADV7192 will come out of Sleep Mode and resume normal
operation.
For this to operate Power up in Sleep Mode control has to be
enabled (MR60 is set to a Logic 0), otherwise Sleep Mode is
controlled by the PAL_NTSC and SCRESET/RTC/TR pins.
Figure 58.Mode Register 2, MR2
Table III.DAC Output Configuration

NOTE
ADV7192
MODE REGISTER 3
MR3 (MR37–MR30)
(Address (SR4–SR0) = 03H)

Mode Register 3 is an 8-bit-wide register. Figure 59 shows the
various operations under the control of Mode Register 3.
MR3 BIT DESCRIPTION
Revision Code (MR30–MR31)

This bit is read only and indicates the revision of the device.
VBI Open (MR32)

This bit determines whether or not data in the Vertical Blanking
Interval (VBI) is output to the analog outputs or blanked. Note
that this condition is also valid in Timing Slave Mode 0. For
further information see Vertical Blanking Data Insertion and
BLANK Input section.
Teletext Enable (MR33)

This bit must be set to 1 to enable teletext data insertion on the
TTX pin. Note: TTX functionality is shared with VSO and
CLAMP on Pin 62. CLAMP/VSO Select (MR77) and TTX
Input/CLAMP–VSO Output (MR76) have to be set accordingly.
Teletext Bit Request Mode Control (MR34)

This bit enables switching of the teletext request signal from a
continuous high signal (MR34 = 0) to a bitwise request signal
(MR34 = 1).
Closed Captioning Field Selection (MR35–MR36)

These bits control the fields that closed captioning data is dis-
played on, closed captioning information can be displayed on
an odd field, even field or both fields.
Reserved (MR37)

A Logic 0 must be written to this bit.
MODE REGISTER 4
MR4 (MR47–MR40)
(Address (SR4–SR0) = 04H)

Mode Register 4 is an 8-bit-wide register. Figure 60 shows the
various operations under the control of Mode Register 4.
MR4 BIT DESCRIPTION
VSYNC_3H Control (MR40)

When this bit is enabled (1) in Slave Mode, it is possible to
drive the VSYNC input low for 2.5 lines in PAL mode and
three lines in NTSC mode. When this bit is enabled in Master
Mode the ADV7192 outputs an active low VSYNC signal for three
lines in NTSC mode and 2.5 lines in PAL mode.
Genlock Control (MR41–MR42)

These bits control the Genlock feature and timing reset of the
ADV7192. Setting MR41 and MR42 to Logic 0 disables the
SCRESET/RTC/TR pin and allows the ADV7192 to operate
in normal mode.By setting MR41 to zero and MR42 to one, a timing reset is
applied, resetting the horizontal and vertical counters. This
has the effect of resetting the Field Count to Field 0.
If the SCRESET/RTC/TR pin is held high, the counters
will remain reset. Once the pin is released the counters will
commence counting again. For correct counter reset, the
SCRESET/RTC/TR pin has to remain high for at least
37 ns (one clock cycle at 27 MHz).If MR41 is set to one and MR42 is set to zero, the SCRESET/
RTC/TR pin is configured as a subcarrier reset input and
the subcarrier phase will reset to Field 0 whenever a low-to-
high transition is detected on the SCRESET/RTC/TR pin
(SCH phase resets at the start of the next field).If MR41 is set to one and MR42 is set to one, the SCRESET/
RTC/TR pin is configured as a real time control input and
the ADV7192 can be used to lock to an external video source
working in RTC mode. See Real-Time Control, Subcarrier
Reset and Timing Reset section.
Active Video Line Duration (MR43)

This bit switches between two active video line durations. A zero
selects CCIR Rec. 601 (720 pixels PAL/NTSC) and a one
selects ITU-R BT. 470 standard for active video duration (710
pixels NTSC, 702 pixels PAL).
Chrominance Control (MR44)

This bit enables the color information to be switched on and off
the chroma, composite and color component outputs.
Burst Control (MR45)

This bit enables the color burst to be switched on and off the
chroma and composite outputs.
Color Bar Control (MR46)

This bit can be used to generate and output an internal color
bar test pattern. The color bar configuration is 100/7.5/75/7.5
for NTSC and 100/0/75/0 for PAL. It is important to note that
when color bars are enabled the ADV7192 is configured in a
Master Timing mode. The output pins VSYNC, HSYNC and
BLANK are three-state during color bar mode.
Interlaced Mode Control (MR47)

This bit is used to setup the output to interlaced or noninterlaced
mode.
MODE REGISTER 5
MR5 (MR57–MR50)
(Address (SR4–SR0) = 05H)

Mode Register 5 is a 8-bit-wide register. Figure 61 shows the
various operations under the control of Mode Register 5.
MR5 BIT DESCRIPTION
Y-Level Control (MR50)

This bit controls the component Y output level on the ADV7192
If this bit is set (0), the encoder outputs Betacam levels when
configured in PAL or NTSC mode. If this bit is set (1), the
encoder outputs SMPTE levels when configured in PAL or
NTSC mode.
UV-Levels Control (MR51–MR52)

These bits control the component U and V output levels on the
ADV7192. It is possible to have UV levels with a peak-to-peak
amplitude of either 700 mV (MR52 + MR51 = 01) or 1000 mV
(MR52 + MR51 = 10) in NTSC and PAL. It is also possible to
have default values of 934 mV for NTSC and 700 mV for PAL
(MR52 + MR51 = 00).
RGB Sync (MR53)

This bit is used to set up the RGB outputs with the sync infor-
mation encoded on all RGB outputs.
Clamp Delay (MR54–MR55)

These bits control the delay or advance of the CLAMP signal in
the front or back porch of the ADV7192. It is possible to delay or
advance the pulse by zero, one, two or three clock cycles.
Note: TTX functionality is shared with VSO and CLAMP on Pin
62. CLAMP/VSO Select (MR77) and TTX Input/CLAMP–VSO
Output (MR76) have to be set accordingly.
Clamp Delay Direction (MR56)

This bit controls a positive or negative delay in the CLAMP sig-
nal. If this bit is set (1), the delay is negative. If it is set (0), the
delay is positive.
Clamp Position (MR57)

This bit controls the position of the CLAMP signal. If this bit is
set (1), the CLAMP signal is located in the back porch position.
If this bit is set (0), the CLAMP signal is located in the front
porch position.
Figure 61.Mode Register 5, MR5
Figure 60.Mode Register 4, MR4
ADV7192
Mode Register 6
MR6 (MR67–MR60)
(Address (SR4–SR0) = 06H)

Mode Register 6 is a 8-bit-wide register. Figure 62 shows the
various operations under the control of Mode Register 6.
MR6 BIT DESCRIPTION
Power-Up Sleep Mode Control (MR60)

After RESET is applied this control is enabled (MR60 = 0) if
both SCRESET/RTC/TR and NTSC_PAL pins are tied high.
The ADV7192 will then power up in Sleep Mode to facilitate
low power consumption before the I2C is initialized. When this
control is disabled (MR60 = 1, via the I2C) Sleep Mode control
passes to Sleep Mode Control, MR27.
PPL Enable Control (MR61)

The PLL control should be enabled (MR61 = 0 ) when 4×
Oversampling is enabled (MR16 = 1). When this bit is toggled,
it is also used to reset the PLL.
Reserved (MR62, MR63, MR64)

A Logical 0 must be written to these bits.
Field Counter (MR65, MR66, MR67)

These three bits are read only bits. The field count can be read
back over the I2C interface. In NTSC mode the field count goes
from 0–3, in PAL Mode from 0–7.
MODE REGISTER 7
MR7 (MR77–MR70)
(Address (SR4–SR0) = 07H)

Mode Register 7 is a 8-bit-wide register. Figure 63 shows the
various operations under the control of Mode Register 7.
MR7 BIT DESCRIPTION
Color Control Enable (MR70)

This bit is used to enable control of contrast and saturation of
color. If this bit is set (1) color controls are enabled (Contrast
Control Register, U-Scale Register, V-Scale Register). If this bit
is set (0), the color control features are disabled.
Luma Saturation Control (MR71)

When this bit is set (1), the luma signal will be clipped if it reaches
a limit that corresponds to an input luma value of 255 (after
scaling by the Contrast Control Register). This prevents the
chrominance component of the composite video signal being
clipped if the amplitude of the luma is too high. When this bit is
set (0), this control is disabled.
Hue Adjust Control (MR72)

This bit is used to enable hue adjustment on the composite and
chroma output signals of the ADV7192. When this bit is set (1),
the hue of the color is adjusted by the phase offset described in
the Hue Adjust Control Register. When this bit is set (0), hue
adjustment is disabled.
Brightness Enable Control (MR73)

This bit is used to enable brightness control on the ADV7192.
The actual brightness level is programmed in the Brightness
Control Register. This value or set-up level is added to the scaled
Y data. When this bit is set (1), brightness control is enabled.
When this bit is set (0), brightness control is disabled.
Sharpness Filter Enable (MR74)

This bit is used to enable the sharpness control of the luminance
signal on the ADV7192 (Luma Filter Select has to be set to Ex-
tended, MR04–MR02 = 100). The various responses of the filter
are determined by the Sharpness Control Register. When this
bit is set (1), the luma response is altered by the amount described
in the Sharpness Control Register. When this bit is set (0), the
sharpness control is disabled. See Internal Filter Response section
for luma signal responses.
CSO_HSO Output Control (MR75)

This bit is used to determine whether HSO or CSO TTL output
signal is output at the CSO_HSO pin. If this bit is set (1), the
CSO TTL signal is output. If this bit is set (0), the HSO TTL
signal is output.
TTX Input/CLAMP–VSO Output (MR76)

This bit controls whether Pin 62 is configured as an output or as
an input pin. A 1 selects Pin 62 to be an output for CLAMP or
VSO functionality. A 0 selects this pin as a TTX input pin.
Figure 62.Mode Register 6, MR6
CLAMP/VSO Select (MR77)
This bit is used to select the functionality of Pin 62. Setting this
bit to 1 selects CLAMP as the output signal. A 0 selects VSO
as the output signal. Since this pin is also shared with the TTX
functionality, TTX Input/CLAMP–VSO Output has to be set
accordingly (MR76).
MODE REGISTER 8
MR8 (MR87–MR80)
(Address (SR4–SR0) = 08H)

Mode Register 8 is an 8-bit-wide register. Figure 64 shows the
various operations under the control of Mode Register 8.
MR8 BIT DESCRIPTION
Progressive Scan Control (MR80)

This control enables the progressive scan inputs on pins
Y(0)/P8–Y(7)/P15, Y(8)–Y(9), Cr(0)–Cr(9), Cb(0)–Cb(9). To
enable this control MR80 has to be set to 1. It is assumed that
the incoming Y data contains all necessary sync information.
Note: Simultaneous progressive scan input and 16-bit pixel input
is not possible.
Reserved (MR81)

A 0 must be written to this bit.
Double Buffer Control (MR82)

Double Buffering can be enabled or disabled on the Contrast
Control Register, U Scale Register, V Scale Register, Hue Adjust
Control Register, Closed Captioning Register, Brightness Control
Register, Gamma Curve Select Bit and the Macrovision Regis-
ters. Double Buffer is not available in Master Mode.
16-Bit Pixel Port (MR83)

This bit controls if the ADV7192 is operated in 8-bit or 16-bit
mode. In 8-bit mode the input data will be set up on Pins P0–P7.
Reserved (MR84)

A Logic 0 must be written to this bit.
DNR Enable Control (MR85)

To enable the DNR process this bit has to be set to 1. If this bit
is set to other DNR processing is bypassed. For further informa-
tion on DNR controls see DNR Mode Control section.
Gamma Enable Control (MR86)

To enable the programmable gamma correction this bit has
to be set to enabled (MR86 = 1). For further information on
Gamma Correction controls see Gamma Correction Registers
selected is Curve A. Otherwise, Curve B is selected. Each curve
will have to be programmed by the user. For further information
on Gamma Correction controls see Gamma Correction Regis-
ters section.
MODE REGISTER 9
MR9 (MR97–MR90)
(Address (SR4–SR0) = 09H)

Mode Register 9 is an 8-bit-wide register. Figure 66 shows the
various operations under the control of Mode Register 9.
MR9 BIT DESCRIPTION
Undershoot Limiter (MR90–MR91)

This control ensures that no luma video data will go below a
programmable level. This prevents any synchronization problems
due to luma signals going below the blanking level. Available
limit levels are –1.5 IRE, –6 IRE, –11 IRE. Note that this facility is
only available in 4× Oversampling mode (MR16 = 1). When the
device is operated in 2× Oversampling mode (MR16 = 0) or RGB
output without RGB sync are selected, the minimum luma level is
set in Timing Register 0, TR06 (Min Luma Control).
Black Burst Y DAC (MR92)

It is possible to output a Black Burst signal from the DAC
which is selected to be the Luma DAC (MR22, MR21, MR20).
This signal can be useful for locking two video sources together
using professional video equipment. See also Black Burst Out-
put section.
Black Burst Luma (MR93)

It is possible to output a Black Burst signal from the DAC which
is selected to be the Y-DAC (MR22, MR21, MR20). This signal
can be useful for locking two video sources together using pro-
fessional video equipment. See also Black Burst Output section.
Figure 64.Mode Register 8, MR8
ic,good price


TEL:86-533-2716050      FAX:86-533-2716790
   

©2020 IC PHOENIX CO.,LIMITED