IC Phoenix
 
Home ›  AA33 > ADP3162JR,5-Bit Programmable 2-Phase Synchronous Buck Controller
ADP3162JR Fast Delivery,Good Price
Part Number:
If you need More Quantity or Better Price,Welcom Any inquiry.
We available via phone +865332716050 Email
Partno Mfg Dc Qty AvailableDescript
ADP3162JRADN/a1500avai5-Bit Programmable 2-Phase Synchronous Buck Controller


ADP3162JR ,5-Bit Programmable 2-Phase Synchronous Buck ControllerSPECIFICATIONSCC REF AParameter Symbol Conditions Min Typ Max UnitFEEDBACK INPUTAccuracy VFB1.05 V ..
ADP3162JR-REEL ,5-Bit Programmable 2-Phase Synchronous Buck ControllerSPECIFICATIONSCC REF AParameter Symbol Conditions Min Typ Max UnitFEEDBACK INPUTAccuracy VFB1.05 V ..
ADP3163 ,5-Bit Programmable 2-/3-Phase Synchronous Buck ControllerSPECIFICATIONS(VCC = 12 V, I = 150 A, T = 0C to 70C, unless otherwise noted.)REF AParameter Symb ..
ADP3163JRU ,5-Bit Programmable 2-/3-Phase Synchronous Buck ControllerSPECIFICATIONS(VCC = 12 V, I = 150 A, T = 0C to 70C, unless otherwise noted.)REF AParameter Symb ..
ADP3163JRU-REEL ,5-Bit Programmable 2-/3-Phase Synchronous Buck ControllerSPECIFICATIONS(VCC = 12 V, I = 150 A, T = 0C to 70C, unless otherwise noted.)REF AParameter Symb ..
ADP3163JRUZ-REEL ,5-Bit Programmable 2-/3-Phase Synchronous Buck ControllerGENERAL DESCRIPTION The ADP3163 also uses a unique supplemental regulation tech-The ADP3163 is a hi ..
AK2302 , Dual PCM Codec/Filter COMBO LSI
AK2302 , Dual PCM Codec/Filter COMBO LSI
AK2305 , Dual PCM CODEC for ISDN TERMINAL ADAPTER
AK2306LV , Dual PCM CODEC for ISDN/VoIP TERMINAL ADAPTER
AK2307LV , SPEECH CODEC for Digital Key telephone (5.0V/3.3V)
AK2358F , Base-band LSI for Europian Cordless Telephones(CTI, CTI)


ADP3162JR
5-Bit Programmable 2-Phase Synchronous Buck Controller
REV.A
5-Bit Programmable 2-Phase
Synchronous Buck Controller
FUNCTIONAL BLOCK DIAGRAM
VCC
REF
GND
COMP
PWM1
PWM2
PWRGD
CS–
CS+
VID3VID2VID1VID0VID25
FEATURES
ADOPT™ Optimal Positioning Technology for Superior
Load Transient Response and Fewest Output
Capacitors
Complies with VRM 8.5 with Lowest System Cost
Active Current Balancing Between Both Output Phases
5-Bit Digitally Programmable 1.05 V to 1.825 V Output
Dual Logic-Level PWM Outputs for Interface to
External High-Power Drivers
Total Output Accuracy �0.8% Over Temperature
Current-Mode Operation
Short Circuit Protection
Power Good Output
Overvoltage Protection Crowbar Protects
Microprocessors with No Additional
External Components
APPLICATIONS
Desktop PC Power Supplies for:
Intel Tualatin Processors
VRM Modules
GENERAL DESCRIPTION

The ADP3162 is a highly efficient dual output synchronous
buck switching regulator controller optimized for converting a
5 V or 12 V main supply into the core supply voltage required by
high-performance processors such as Tualatin. The ADP3162
uses an internal 5-bit DAC to read a voltage identification (VID)
code directly from the processor, which is used to set the output
voltage between 1.05 V and 1.825 V. The ADP3162 uses a
current mode PWM architecture to drive two logic-level outputs
at a programmable switching frequency that can be optimized
for VRM size and efficiency. The output signals are 180 degrees
out of phase, allowing for the construction of two complementary
buck switching stages. These two stages share the dc output
current to reduce overall output voltage ripple. An active cur-
rent balancing function ensures that both phases carry equal
portions of the total load current, even under large transient
loads, to minimize the size of the inductors.
The ADP3162 also uses a unique supplemental regulation tech-
nique called active voltage positioning to enhance load transient
performance. Active voltage positioning results in a dc/dc converter
that meets the stringent output voltage specifications for high
performance processors, with the minimum number of output
capacitors and smallest footprint. Unlike voltage-mode and
standard current-mode architectures, active voltage positioning
adjusts the output voltage as a function of the load current so
that it is always optimally positioned for a system transient. The
ADP3162 also provides accurate and reliable short circuit pro-
tection and adjustable current limiting.
The ADP3162 is specified over the commercial temperature
range of 0°C to 70°C and is available in a 16-lead narrow body
SOIC package.
ADOPT is a trademark of Analog Devices, Inc.
ADP3162–SPECIFICATIONS1(VCC = 12 V, IREF = 150 �A, TA = 0�C to 70�C, unless otherwise noted.)
ADP3162
NOTESAll limits at temperature extremes are guaranteed via correlation using standard Statistical Quality Control (SQC) methods.Guaranteed by design, not tested in production.
Specifications subject to change without notice.
PIN FUNCTION DESCRIPTIONS
ABSOLUTE MAXIMUM RATINGS*

VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .–0.3 V to +15 V
CS+, CS– . . . . . . . . . . . . . . . . . . . . . .–0.3 V to VCC + 0.3 V
All Other Inputs and Outputs . . . . . . . . . . . . .–0.3 V to +10 V
Operating Ambient Temperature Range . . . . . . . 0°C to 70°C
Operating Junction Temperature . . . . . . . . . . . . . . . . . .125°C
Storage Temperature Range . . . . . . . . . . . . .–65°C to +150°C
θJA
Two-Layer Board . . . . . . . . . . . . . . . . . . . . . . . . . . 125°C/W
Four-Layer Board . . . . . . . . . . . . . . . . . . . . . . . . . . 81°C/W
Lead Temperature (Soldering, 10 sec) . . . . . . . . . . . . .300°C
Vapor Phase (60 sec) . . . . . . . . . . . . . . . . . . . . . . . . . . .215°C
Infrared (15 sec) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .220°C
*This is a stress rating only; operation beyond these limits can cause the device to
be permanently damaged. Unless otherwise specified, all voltages are referenced
to GND.
PIN CONFIGURATION
ORDERING GUIDE
CAUTION

ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000V readily
accumulate on the human body and test equipment and can discharge without detection. Although
the ADP3162 features proprietary ESD protection circuitry, permanent damage may occur on
devices subjected to high-energy electrostatic discharges. Therefore, proper ESD precautions are
recommended to avoid performance degradation or loss of functionality.
ADP3162
–Typical Performance Characteristics

TPC 1.Oscillator Frequency vs. Timing Capacitor
TPC 2.Supply Current vs. Oscillator Frequency
OUTPUT ACCURACY – % OF NOMINAL
NUMBER OF PARTS

TPC 3.Output Accuracy Distribution
Figure 1.Closed-Loop Output Voltage Accuracy Test Circuit
Table I. Output Voltage vs. VID Code
THEORY OF OPERATION

The ADP3162 combines a current-mode, fixed frequency PWM
controller with antiphase logic outputs in a controller for a two-
phase synchronous buck power converter. Two-phase operation
is important for switching the high currents required by high
performance microprocessors. Handling the high current in a
single-phase converter would place difficult requirements on the
power components such as inductor wire size, MOSFET ON-
resistance and thermal dissipation. The ADP3162’s high side
current sensing topology ensures that the load currents are bal-
anced in each phase, such that neither phase has to carry more
than half of the power. An additional benefit of high side current
sensing over output current sensing is that the average current
through the sense resistor is reduced by the duty cycle of the
converter allowing the use of a lower power, lower cost resistor.
The outputs of the ADP3162 are logic drivers only and are
not intended to directly drive external power MOSFETs.
Instead, the ADP3162 should be paired with drivers such as
the ADP3412, ADP3413, or ADP3414.
The frequency of the ADP3162 is set by an external capacitor
connected to the CT pin. Each output phase of the ADP3162
operates at half of the frequency set by the CT pin. The error
amplifier and current sense comparator control the duty cycle of
the PWM outputs to maintain regulation. The maximum duty
cycle per phase is inherently limited to 50% because the PWM
outputs toggle in two-phase operation. While one phase is on,
the other phase is off. In no case can both outputs be high at the
same time.
Output Voltage Sensing

The output voltage is sensed at the FB pin allowing for remote
sensing. To maintain the accuracy of the remote sensing, the
GND pin should also be connected close to the load. A voltage
error amplifier (gm) amplifies the difference between the output
voltage and a programmable reference voltage. The reference
voltage is programmed between 1.05 V and 1.825 V by an internal
5-bit DAC, which reads the code at the voltage identification
(VID) pins. (Refer to Table I for the output voltage versus VID pin
code information.)
Active Voltage Positioning

The ADP3162 uses Analog Devices Optimal Positioning Tech-
nology (ADOPT), a unique supplemental regulation technique
that uses active voltage positioning and provides optimal com-
pensation for load transients. When implemented, ADOPT adjusts
the output voltage as a function of the load current, so that it is
always optimally positioned for a load transient. Standard (passive)
voltage positioning has poor dynamic performance, rendering
it ineffective under the stringent repetitive transient conditions
required by high performance processors. ADOPT, however,
provides optimal bandwidth for transient response that yields
optimal load transient response with the minimum number of
output capacitors.
Reference Output

A 3.0V reference is available on the ADP3162. This reference
is normally used to set the voltage positioning accurately using a
resistor divider to the COMP pin. In addition, the reference can
be used for other functions such as generating a regulated voltage
ADP3162
Cycle-by-Cycle Operation

During normal operation (when the output voltage is regulated),
the voltage-error amplifier and the current comparator are the
main control elements. The voltage at the CT pin of the oscilla-
tor ramps between 0V and 3V. When that voltage reaches 3V,
the oscillator sets the driver logic, which sets PWM1 high. Dur-
ing the ON time of Phase 1, the driver IC turns on the high-side
MOSFET. The CS+ and CS– pins monitor the current through
the sense resistor that feeds both high-side MOSFETs. When
the voltage between the two pins exceeds the threshold level
set by the voltage error amplifier (gm), the driver logic is reset
and the PWM output goes low. This signals the driver IC to turn
off the high-side MOSFET and turn on the low-side MOSFET.
On the next cycle of the oscillator, the driver logic toggles and
sets PWM2 high. On each following cycle of the oscillator, the
outputs toggle between PWM1 and PWM2. In each case, the
current comparator resets the PWM output low when the current
comparator threshold is reached. As the load current increases,
the output voltage starts to decrease. This causes an increase in
the output of the gm amplifier, which in turn leads to an increase
in the current comparator threshold, thus programming more
current to be delivered to the output so that voltage regulation is
maintained.
Active Current Sharing

The ADP3162 ensures current balance in the two phases by
actively sensing the current through a single sense resistor. During
one phase’s ON time, the current through the respective high-side
MOSFET and inductor is measured through the sense resistor
(R4 in Figure 2). When the comparator (CMP1 in the Functional
Block Diagram) threshold programmed by the gm amplifier is
reached, the high-side MOSFET turns off. In the next cycle the
ADP3162 switches to the second phase. The current is measured
with the same sense resistor and the same internal comparator,
ensuring accurate matching. This scheme is immune to imbalances
in the MOSFETs’ RDS(ON) and inductors’ parasitic resistances.
If for some reason one of the phases fails, the other phase will still
be limited to its maximum output current (one-half of the short
circuit current limit). If this is not sufficient to supply the load,
the output voltage will droop and cause the PWRGD output to
signal that the output voltage has fallen out of its specified range.
Short Circuit Protection

The ADP3162 has multiple levels of short circuit protection to
ensure fail-safe operation. The sense resistor and the maximum
current sense threshold voltage given in the specifications set the
peak current limit.
When the load current exceeds the current limit, the excess current
discharges the output capacitor. When the output voltage is below
the foldback threshold VFB(LOW), the maximum deliverable output
current is cut by reducing the current sense threshold from the
current limit threshold, VCS(CL), to the foldback threshold,
VCS(FOLD). Along with the resulting current foldback, the oscilla-
tor frequency is reduced by a factor of five when the output is
0 V. This further reduces the average current in short circuit.
Power-Good Monitoring

The Power-Good comparator monitors the output voltage of the
supply via the FB pin. The PWRGD pin is an open drain output
whose high level (when connected to a pull-up resistor) indi-
cates that the output voltage is within the specified range of
the nominal output voltage requested by the VID DAC. PWRGD
will go low if the output is outside this range.
Output Crowbar

The ADP3162 includes a crowbar comparator that senses when
the output voltage rises higher than the specified trip thresh-
old, VCROWBAR. This comparator overrides the control loop and
sets both PWM outputs low. The driver ICs turn off the high side
MOSFETs and turn on the low-side MOSFETs, thus pulling the
output down as the reversed current builds up in the inductors. If
the output overvoltage is due to a short of the high side MOSFET,
this action will current limit the input supply or blow its fuse,
ic,good price


TEL:86-533-2716050      FAX:86-533-2716790
   

©2020 IC PHOENIX CO.,LIMITED