IC Phoenix
 
Home ›  AA29 > ADM1024ARUZ-ADM1024ARUZ-REEL,Reconfigurable Remote Temperature Sensor and Supply Voltage Monitor, Fan Control, Chassis Intrusion with Serial Interface
ADM1024ARUZ-ADM1024ARUZ-REEL Fast Delivery,Good Price
Part Number:
If you need More Quantity or Better Price,Welcom Any inquiry.
We available via phone +865332716050 Email
Partno Mfg Dc Qty AvailableDescript
ADM1024ARUZADN/a86avaiReconfigurable Remote Temperature Sensor and Supply Voltage Monitor, Fan Control, Chassis Intrusion with Serial Interface
ADM1024ARUZADIN/a339avaiReconfigurable Remote Temperature Sensor and Supply Voltage Monitor, Fan Control, Chassis Intrusion with Serial Interface
ADM1024ARUZ-REEL |ADM1024ARUZREELONN/a17avaiReconfigurable Remote Temperature Sensor and Supply Voltage Monitor, Fan Control, Chassis Intrusion with Serial Interface


ADM1024ARUZ ,Reconfigurable Remote Temperature Sensor and Supply Voltage Monitor, Fan Control, Chassis Intrusion with Serial InterfaceSystem Hardware Monitor withRemote Diode Thermal SensingADM1024
ADM1024ARUZ ,Reconfigurable Remote Temperature Sensor and Supply Voltage Monitor, Fan Control, Chassis Intrusion with Serial InterfaceAPPLICATIONSUp to 9 Measurement Channels Network Servers and Personal ComputersInputs Programmable- ..
ADM1024ARUZ-REEL ,Reconfigurable Remote Temperature Sensor and Supply Voltage Monitor, Fan Control, Chassis Intrusion with Serial InterfaceGENERAL DESCRIPTIONOn-Chip Temperature Sensor The ADM1024 is a complete system hardware monitor for ..
ADM1025ARQ ,Low-Cost PC Hardware Monitor ASICSPECIFICATIONSA MIN MAX CC MIN MAXParameter Min Typ Max Unit Test Conditions/CommentsPOWER SUPPLYSu ..
ADM1025ARQ-REEL ,Remote Multichannel Temperature Sensor, Power Supply Voltage Monitor with Serial Interfaceapplications in personal computers,electronic test equipment, and office electronics.FUNCTIONAL BLOC ..
ADM1025ARQ-REEL ,Remote Multichannel Temperature Sensor, Power Supply Voltage Monitor with Serial InterfaceSPECIFICATIONSA MIN MAX CC MIN MAXParameter Min Typ Max Unit Test Conditions/CommentsPOWER SUPPLYSu ..
AH103A-G , High Gain, High Linearity ½-Watt Amplifier
AH103A-G , High Gain, High Linearity ½-Watt Amplifier
AH104F245001-T , CHIP ANTENNA
AH104F245001-T , CHIP ANTENNA
AH104F2450S1-T , CHIP ANTENNA
AH104F2450S1-T , CHIP ANTENNA


ADM1024ARUZ-ADM1024ARUZ-REEL
Reconfigurable Remote Temperature Sensor and Supply Voltage Monitor, Fan Control, Chassis Intrusion with Serial Interface
REV.B
System Hardware Monitor with
Remote Diode Thermal Sensing
FEATURES
Up to 9 Measurement Channels
Inputs Programmable-to-Measure Analog Voltage, Fan
Speed, or External Temperature
External Temperature Measurement with Remote
Diode (2 Channels)
On-Chip Temperature Sensor
5 Digital Inputs for VID Bits
LDCM Support
System Management Bus (SMBus)
Chassis Intrusion Detect
Interrupt and Overtemperature Outputs
Programmable RESET Input Pin
Shutdown Mode to Minimize Power Consumption
Limit Comparison of All Monitored Values
FUNCTIONAL BLOCK DIAGRAM
GENERAL DESCRIPTION

The ADM1024 is a complete system hardware monitor for
microprocessor based systems, providing measurement and limit
comparison of various system parameters. Eight measurement
inputs are provided; three are dedicated to monitoring 5 V and
12 V power supplies and the processor core voltage. The
ADM1024 can monitor a fourth power supply voltage by mea-
suring its own VCC. One input (two pins) is dedicated to a
remote temperature-sensing diode. Two more pins can be
(continued on page 7)
APPLICATIONS
Network Servers and Personal Computers
Microprocessor Based Office Equipment
Test Equipment and Measuring Instruments
ADM1024–SPECIFICATIONS1, 2
(TA = TMIN to TMAX, VCC = VMIN to VMAX, unless otherwise noted.)

DIGITAL OUTPUTS NTEST_OUT
OPEN-DRAIN DIGITAL OUTPUTS
OPEN-DRAIN SERIAL DATA BUS OUTPUT (SDA)
ADM1024
NOTESAll voltages are measured with respect to GND, unless otherwise specified.Typicals are at TA = 25°C and represent most likely parametric norm. Shutdown current typ is measured with VCC = 3.3 V.TUE (Total Unadjusted Error) includes Offset, Gain, and Linearity errors of the ADC, multiplexer, and on-chip input attenuators, including an external series input
protection resistor value between 0 kΩ and 1 kΩ.Total monitoring cycle time is nominally m × 755 µs + n × 33244 µs, where m is the number of channels configured as analog inputs, plus 2 for the internal VCC
measurement and internal temperature sensor, and n is the number of channels configured as external temperature channels (D1 and D2).The total fan count is based on two pulses per revolution of the fan tachometer output.Open-drain digital outputs may have an external pull-up resistor connected to a voltage lower or higher than VCC (up to 6.5 V absolute maximum).All logic inputs except ADD are tolerant of 5 V logic levels, even if VCC is less than 5 V. ADD is a three-state input that may be connected to VCC, GND, or left
open-circuit.Timing specifications are tested at logic levels of VIL = 0.8 V for a falling edge and VIH = 2.2 V for a rising edge.
Specifications subject to change without notice.
Figure 1.Diagram for Serial Bus Timing
ADM1024
CAUTION

ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000V readily
accumulate on the human body and test equipment and can discharge without detection. Although the
ADM1024 features proprietary ESD protection circuitry, permanent damage may occur on devices
subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended
to avoid performance degradation or loss of functionality.
ABSOLUTE MAXIMUM RATINGS*

Positive Supply Voltage (VCC) . . . . . . . . . . . . . . . . . . . . . 6.5 V
Voltage on 12 V VIN Pin . . . . . . . . . . . . . . . . . . . . . . . . . 20 V
Voltage on AOUT, N TEST_OUT ADD,
2.5 VIN/D2+ . . . . . . . . . . . . . . . . . . –0.3 V to (VCC + 0.3 V)
Voltage on Any Other Input or Output Pin . . –0.3 V to +6.5 V
Input Current at Any Pin . . . . . . . . . . . . . . . . . . . . . . . ±5 mA
Package Input Current . . . . . . . . . . . . . . . . . . . . . . . ±20 mA
Maximum Junction Temperature (TJ max) . . . . . . . . . . 150°C
Storage Temperature Range . . . . . . . . . . . . –65°C to +150°C
Lead Temperature, Soldering
Vapor Phase 60 sec . . . . . . . . . . . . . . . . . . . . . . . . . . 235°C
Infrared 15 sec . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200°C
ESD Rating All Pins . . . . . . . . . . . . . . . . . . . . . . . . . . 2000 V
*Stresses above those listed under Absolute Maximum Ratings may cause perma-
nent damage to the device. This is a stress rating only; functional operation of the
device at these or any other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability.
THERMAL CHARACTERISTICS

24-Lead, Small Outline Package: �JA = 50°C/W, �JC = 10°C/W
PIN CONFIGURATION
ORDERING GUIDE

*Z = Pb-free part.
PIN FUNCTION DESCRIPTIONS
7CIDigital I/O. An active high input from an external latch that captures a Chassis Intrusion event.
8GND
9VCC
ADM1024–Typical Performance Characteristics
LEAKAGE RESISTANCE – M�
TEMPERATURE ERROR –
30
–20

TPC 1.Temperature Error vs. PC Board Track Resistance
TPC 2.Temperature Error vs. Power Supply
Noise Frequency
FREQUENCY – Hz50M500
TEMPERATURE ERROR –
50k500k5M
TPC 3.Temperature Error vs. Common-Mode
Noise Frequency
TPC 4.ADM1024 Reading vs. Pentium® III Tem-
perature Measurement

TPC 5.Temperature Error vs. Capacitance
Between D+ and D–
FREQUENCY – Hz5050M500
TEMPERATURE ERROR –
50k500k5M
100k25M

TPC 6.Temperature Error vs. Differential-Mode
Noise Frequency
TPC 7.Standby Current vs. Temperature
(continued from page 1)
configured as inputs to monitor a 2.5 V supply and a second
processor core voltage, or as a second temperature-sensing input.
The remaining two inputs can be programmed as general-pur-
pose analog inputs or as digital fan-speed measuring inputs.
Measured values can be read out via an SMBus serial System
Management Bus, and values for limit comparisons can be
programmed in over the same serial bus. The high speed succes-
sive-approximation ADC allows frequent sampling of all analog
channels to ensure a fast interrupt response to any out-of-limit
measurement.
The ADM1024’s 2.8 V to 5.5 V supply voltage range, low sup-
ply current, and SMBus interface make it ideal for a wide range
of applications. These include hardware monitoring and protection
applications in personal computers, electronic test equipment,
and office electronics.
MEASUREMENT INPUTS

Programmability of the measurement inputs makes the ADM1024
extremely flexible and versatile. The device has a 10-bit ADC
and nine measurement input pins that can be configured in differ-
ent ways.
Pins 5 and 6 can be programmed as general-purpose analog
inputs with a range of 0 V to 2.5 V, or as digital inputs to moni-
tor the speed of fans with digital tachometer outputs. The fan
inputs can be programmed to accommodate fans with different
speeds and different numbers of pulses per revolution from their
tachometer outputs.
Pins 13 and 14 are dedicated temperature inputs and may be
connected to the cathode and anode of an external temperature-
sensing diode.
Pins 15, 16, and 19 are dedicated analog inputs with on-chip
attenuators, configured to monitor 12 V, 5 V, and the processor
core voltage, respectively.
Pins 17 and 18 may be configured as analog inputs with on-chip
attenuators to monitor a second processor core voltage and a
2.5 V supply, or they may be configured as a temperature input
and connected to a second temperature-sensing diode.
Finally, the ADM1024 monitors the supply from which it is
powered, so there is no need for a separate 3.3 V analog input if
the chip VCC is 3.3 V. The range of this VCC measurement
can be configured for either a 3.3 V or 5 V VCC by Bit 3 of the
Channel Mode Register.
SEQUENTIAL MEASUREMENT

When the ADM1024 monitoring sequence is started, it cycles
sequentially through the measurement of analog inputs and the
temperature sensor, while at the same time the fan speed inputs
are independently monitored. Measured values from these inputs
are stored in Value Registers. These can be read out over the
serial bus, or can be compared with programmed limits stored
in the Limit Registers. The results of out-of-limit comparisons
are stored in the Interrupt Status Registers, and will generate an
interrupt on the INT line (Pin 10).
Any or all of the Interrupt Status Bits can be masked by appro-
priate programming of the Interrupt Mask Register.
PROCESSOR VOLTAGE ID

Five digital inputs (VID4 to VID0—Pins 20 to 24) read the
processor voltage ID code. These inputs can also be reconfigured
as interrupt inputs.
The VID pins have internal 100 kΩ pull-up resistors.
CHASSIS INTRUSION

A chassis intrusion input (Pin7) is provided to detect unautho-
rized tampering with the equipment.
RESET

A RESET input/output (Pin 12) is provided. Pulling this pin low
will reset all ADM1024 internal registers to default values. The
ADM1024 can also be programmed to give a low going 45 ms
reset pulse at this pin.
The RESET pin has an internal, 100 kΩ pull-up resistor.
ANALOG OUTPUT

The ADM1024 contains an on-chip, 8-bit DAC with an out-
put range of 0 V to 2.5 V (Pin 11). This is typically used to
implement a temperature controlled fan by controlling the
speed of a fan dependent upon the temperature measured by the
on-chip temperature sensor.
Testing of board level connectivity is simplified by providing a
NAND tree test function. The AOUT (Pin 11) also doubles as
a NAND test input, while Pin 1 doubles as a NAND tree output.
INTERNAL REGISTERS OF THE ADM1024

A brief description of the ADM1024’s principal internal regis-
ters follows. More detailed information on the function of each
register is given in Tables VI to XIX.
Configuration Registers: Provide control and configuration.
Channel Mode Register: Stores the data for the operating

modes of the input channels.
Address Pointer Register: This register contains the address

that selects one of the other internal registers. When writing to
ADM1024
Interrupt (INT) Status Registers: Two registers to provide

status of each Interrupt event. These registers are also mirrored
at addresses 4Ch and 4Dh.
Interrupt (INT) Mask Registers: Allow masking of individual

interrupt sources.
Temperature Configuration Register: The configuration of

the temperature interrupt is controlled by the lower three bits of
this register.
VID/Fan Divisor Register: The status of the VID0 to VID4

pins of the processor can be written to and read from these
registers. Divisor values for fan speed measurement are also
stored in this register.
Value and Limit Registers: The results of analog voltage

inputs, temperature, and fan speed measurements are stored in
these registers, along with their limit values.
Analog Output Register: The code controlling the analog

output DAC is stored in this register.
Chassis Intrusion Clear Register: A signal latched on the

chassis intrusion pin can be cleared by writing to this register.
SERIAL BUS INTERFACE

Control of the ADM1024 is carried out via the serial bus. The
ADM1024 is connected to this bus as a slave device, under the
control of a master device, e.g., ICH.
The ADM1024 has a 7-bit serial bus address. When the device
is powered up, it will do so with a default serial bus address. The
five MSBs of the address are set to 01011, and the two LSBs are
determined by the logical states of Pin 1 (NTEST OUT/ADD).
This is a three-state input that can be grounded, connected to
VCC, or left open-circuit to give three different addresses.
Table I.ADD Pin Truth Table

If ADD is left open-circuit, the default address will be 0101100.
ADD is sampled only at power-up, so any changes made while
power is on will have no immediate effect.
The facility to make hardwired changes to A1 and A0 allows the
user to avoid conflicts with other devices sharing the same serial
bus, for example, if more than one ADM1024 is used in a system.
The serial bus protocol operates as follows:The master initiates data transfer by establishing a START
condition, defined as a high-to-low transition on the serial
data line SDA while the serial clock line, SCL, remains high.
This indicates that an address/data stream will follow. All
slave peripherals connected to the serial bus respond to the
START condition, and shift in the next eight bits, consisting
of a 7-bit address (MSB first) plus an R/W bit, which deter-
mines the direction of the data transfer, i.e., whether data
will be written to or read from the slave device.
The peripheral whose address corresponds to the transmitted
address responds by pulling the data line low during the low
period before the ninth clock pulse, known as the Acknowl-
edge Bit. All other devices on the bus now remain idle while
the selected device waits for data to be read from or written
to it. If the R/W bit is a 0, the master will write to the slave
device. If the R/W bit is a 1, the master will read from the
slave device.Data is sent over the serial bus in sequences of nine clock
pulses, eight bits of data followed by an Acknowledge Bit
from the slave device. Transitions on the data line must
occur during the low period of the clock signal and remain
stable during the high period, as a low-to-high transition
when the clock is high may be interpreted as a STOP signal.
The number of data bytes that can be transmitted over the
serial bus in a single Read or Write operation is limited only
by what the master and slave devices can handle.When all data bytes have been read or written, stop condi-
tions are established. In Write mode, the master will pull the
data line high during the tenth clock pulse to assert a
STOP condition. In Read mode, the master device will
override the Acknowledge Bit by pulling the data line high
during the low period before the ninth clock pulse. This is
known as No Acknowledge. The master will then take the
data line low during the low period before the tenth clock
pulse, then high during the tenth clock pulse to assert a STOP
condition.
Any number of bytes of data may be transferred over the serial
bus in one operation, but it is not possible to mix read and write
in one operation because the type of operation is determined at
the beginning and cannot subsequently be changed without
starting a new operation.
In the case of the ADM1024, write operations contain either
one or two bytes, and read operations contain one byte and
perform the following functions.
To write data to one of the device data registers or read data
from it, the Address Pointer Register must be set so that the
correct data register is addressed, then data can be written into
that register or read from it. The first byte of a write operation
always contains an address that is stored in the Address Pointer
Register. If data is to be written to the device, the write opera-
tion contains a second data byte that is written to the register
selected by the Address Pointer Register. This is illustrated in
Figure 2a. The device address is sent over the bus followed by
R/W set to 0. This is followed by two data bytes. The first data
byte is the address of the internal data register to be written to,
which is stored in the Address Pointer Register. The second
data byte is the data to be written to the internal data register.
When reading data from a register, there are two possibilities:If the ADM1024’s Address Pointer Register value is unknown
or not the desired value, it is first necessary to set it to the
correct value before data can be read from the desired data
register. This is done by performing a write to the ADM1024
as before, but only the data byte containing the register ad-
dress is sent, as data is not to be written to the register. This
is shown in Figure 2b.
A read operation is then performed consisting of the serial
bus address, R/W bit set to 1, followed by the data byte read
from the data register. This is shown in Figure 2c.If the Address Pointer Register is known to be already at the
desired address, data can be read from the corresponding
data register without first writing to the Address Pointer
Register, so Figure 2b can be omitted.
NOTESAlthough it is possible to read a data byte from a data regis-
ter without first writing to the Address Pointer Register, if
the Address Pointer Register is already at the correct value it
is not possible to write data to a register without writing to
the Address Pointer Register because the first data byte of a
write is always written to the Address Pointer Register.In Figures 2a to 2c, the serial bus address is shown as the
default value 01011(A1)(A0), where A1 and A0 are set by
the three-state ADD pin.
MEASUREMENT INPUTS

The ADM1024 has nine external measurement pins that can be
configured to perform various functions by programming the
Channel Mode Register.
Pins 13 and 14 are dedicated to temperature measurement,
while Pins 15, 16, and 19 are dedicated analog input channels.
Their function is unaffected by the Channel Mode Register.
Pins 5 and 6 can be individually programmed as analog inputs,
or as digital fan speed measurement inputs, by programming
Bits 0 and 1 of the Channel Mode Register.
Pins 17 and 18 can be configured as analog inputs or as inputs
for external temperature-sensing diodes by programming Bit 2
of the Channel Mode Register.
Bit 3 of the Channel Mode Register configures the internal VCC
measurement range for either 3.3 V or 5 V.
Bits 4 to 6 of the Channel Mode Register enable or disable Pins
22 to 24 when they are configured as interrupt inputs by setting
Bit 7 of the Channel Mode Register. This function is controlled
for Pins 20 and 21 by Bits 6 and 7 of Configuration Register 2.
Bit 7 of the Channel Mode Register allows the processor core
voltage ID bits (VID0 to VID4, Pins 24 to 20) to be reconfigured
as interrupt inputs.
A truth table for the Channel Mode Register is given in Table II.
ADM1024
Figure 2a.Writing a Register Address to the Address Pointer Register, then Writing Data to the Selected Register

Figure 2b. Writing to the Address Pointer Register Only
Figure 2c. Reading Data from a Previously Selected Register
Table II.Channel Mode Register
Power-On Default = 0000 0000
Table III.A/D Output Code vs. VIN
ADM1024
ANALOG-TO-DIGITAL CONVERTER

These inputs are multiplexed into the on-chip, successive
approximation, analog-to-digital converter (ADC). This has a
resolution of eight bits. The basic input range is 0 V to 2.5 V,
which is the input range of AIN1 and AIN2, but five of the
inputs have built-in attenuators to allow measurement of 2.5 V,
5 V, 12 V, and the processor core voltages VCCP1 and VCCP2
without any external components. To allow for the tolerance of
these supply voltages, the ADC produces an output of 3/4 full
scale (decimal 192) for the nominal input voltage, and so has
adequate headroom to cope with overvoltages. Table III
shows the input ranges of the analog inputs and output codes
of the ADC.
When the ADC is running, it samples and converts an input
every 748 µs, except for the external temperature (D1 and D2)
inputs. These have special input signal conditioning and are
averaged over 16 conversions to reduce noise, and a measurement
on one of these inputs takes nominally 9.6 ms.
INPUT CIRCUITS

The internal structure for the analog inputs is shown in Figure 3.
Each input circuit consists of an input protection diode, an
attenuator, plus a capacitor to form a first-order low-pass filter
that gives the input immunity to high frequency noise.
Figure 3.Structure of Analog Inputs
2.5 V INPUT PRECAUTIONS

When using the 2.5 V input, the following precautions should
be noted. There is a parasitic diode between Pin 18 and VCC
due to the presence of a PMOS current source (which is used
when Pin 18 is configured as a temperature input). This will
become forward biased if Pin 18 is more than 0.3 V above VCC.
Therefore, VCC should never be powered off with a 2.5 V input
connected.
SETTING OTHER INPUT RANGES

AIN1 and AIN2 can easily be scaled to voltages other than 2.5 V.
If the input voltage range is zero to some positive voltage, all
that is required is an input attenuator, as shown in Figure 4.
Figure 4.Scaling AIN(1–2)
Negative and bipolar input ranges can be accommodated by
using a positive reference voltage to offset the input voltage
range so it is always positive.
To measure a negative input voltage, an attenuator can be used
as shown in Figure 5.
Figure 5.Scaling and Offsetting AIN(1–2) for
Negative Inputs
This is a simple and cheap solution, but the following point
should be noted. Since the input signal is offset but not inverted,
the input range is transposed. An increase in the magnitude of
the –12 V supply (going more negative) will cause the input
voltage to fall and give a lower output code from the ADC.
Conversely, a decrease in the magnitude of the –12 V supply
will cause the ADC code to increase. The maximum negative
voltage corresponds to zero output from the ADC. This means
that the upper and lower limits will be transposed.
Bipolar input ranges can easily be accommodated. By making
R1 equal to R2 and VOS = 2.5 V, the input range is ±2.5 V.
Other input ranges can be accommodated by adding a third
resistor to set the positive full-scale input voltage.
Figure 6.Scaling and Offsetting AIN(1–2) for
Bipolar Inputs
(R3 has no effect as the input voltage at the device pin is zero
when VIN = minus full scale.)
(R2 has no effect as the input voltage at the device pin is 2.5 V
when VIN = plus full scale).
Offset voltages other than 2.5 V can be used, but the calculation
becomes more complicated.
TEMPERATURE MEASUREMENT SYSTEM
Internal Temperature Measurement

The ADM1024 contains an on-chip band gap temperature sensor,
whose output is digitized by the on-chip ADC. The temperature
data is stored in the Temperature Value Register (address 27h)
and the LSB from Bits 6 and 7 of the Temperature Configuration
Register (address 4Bh). As both positive and negative tempera-
tures can be measured, the temperature data is stored in twos
complement format, as shown in Table IV. Theoretically, the
temperature sensor and ADC can measure temperatures from
–128°C to +127°C with a resolution of 1°C, although tempera-
tures below –40°C and above +125°C are outside the operating
temperature range of the device.
External Temperature Measurement

The ADM1024 can measure the temperature of two external
diode sensors or diode connected transistors, connected to
Pins 13 and 14 or 17 and 18.
Pins 13 and 14 are a dedicated temperature input channel.
Pins 17 and 18 can be configured to measure a diode sensor by
setting Bit 2 of the Channel Mode Register to 1.
The forward voltage of a diode or diode connected transistor,
operated at a constant current, exhibits a negative temperature
coefficient of about –2 mV/°C. Unfortunately, the absolute
value of VBE varies from device to device, and individual calibra-
tion is required to null this out, so the technique is unsuitable
for mass-production.
The technique used in the ADM1024 is to measure the change
in VBE when the device is operated at two different currents.
This is given by:
where:
K is Boltzmann’s constant.
q is the charge on the carrier.
T is the absolute temperature in Kelvins.
N is the ratio of the two currents.
Figure 7 shows the input signal conditioning used to measure the
output of an external temperature sensor. This figure shows the
external sensor as a substrate transistor provided for temperature
monitoring on some microprocessors, but it could equally well
be a discrete transistor.
Figure 7.Signal Conditioning for External Diode
Temperature Sensors
If a discrete transistor is used, the collector will not be grounded
and should be linked to the base. If a PNP transistor is used, the
base is connected to the D– input and the emitter to the D+ input.
If an NPN transistor is used, the emitter is connected to the D–
input and the base to the D+ input.
To prevent ground noise from interfering with the measurement,
the more negative terminal of the sensor is not referenced to
ground, but is biased above ground by an internal diode at the
D– input. As the sensor is operating in a noisy environment, C1
is provided as a noise filter. See the section on layout consider-
ations for more information on C1.
To measure �VBE, the sensor is switched between operating
currents of I and N × I. The resulting waveform is passed
through a 65 kHz low-pass filter to remove noise, then to a
chopper stabilized amplifier that performs the functions of
amplification and rectification of the waveform to produce a dc
voltage proportional to �VBE. This voltage is measured by the
ADC to give a temperature output in 8-bit twos complement
format. To further reduce the effects of noise, digital filtering is
performed by averaging the results of 16 measurement cycles.
An external temperature measurement takes nominally 9.6 ms.
The results of external temperature measurements are stored in
8-bit, twos complement format, as illustrated in Table IV.
Table IV. Temperature Data Format
ADM1024
LAYOUT CONSIDERATIONS

Digital boards can be electrically noisy environments, and care
must be taken to protect the analog inputs from noise, particu-
larly when measuring the very small voltages from a remote
diode sensor. The following precautions should be taken:Place the ADM1024 as close as possible to the remote sens-
ing diode. Provided that the worst noise sources such as
clock generators, data/address buses, and CRTs are avoided,
this distance can be 4 inches to 8 inches.Route the D+ and D– tracks close together, in parallel, with
grounded guard tracks on each side. Provide a ground plane
under the tracks if possible.Use wide tracks to minimize inductance and reduce noise
pickup. A 10 mil track minimum width and spacing is
recommended.
Figure 8.Arrangement of Signal TracksTry to minimize the number of copper/solder joints, which
can cause thermocouple effects. Where copper/solder joints
are used, make sure that they are in both the D+ and D–
path and at the same temperature.
Thermocouple effects should not be a major problem as 1°C
corresponds to about 240 µV, and thermocouple voltages are
about 3 µV/°C of temperature difference. Unless there are two
thermocouples with a big temperature differential between
them, thermocouple voltages should be much less than
200 mV.Place 0.1 µF bypass and 2200 pF input filter capacitors close
to the ADM1024.If the distance to the remote sensor is more than 8 inches,
the use of twisted pair cable is recommended. This will work
up to about 6 feet to 12 feet.For really long distances (up to 100 feet) use shielded twisted
pair such as Belden #8451 microphone cable. Connect the
twisted pair to D+ and D– and the shield to GND close to
the ADM1024. Leave the remote end of the shield uncon-
nected to avoid ground loops.
Because the measurement technique uses switched current
sources, excessive cable and/or filter capacitance can affect the
measurement. When using long cables, the filter capacitor may
be reduced or removed.
Cable resistance can also introduce errors. A 1 Ω series resis-
tance introduces about 0.5°C error.
LIMIT VALUES

Limit values for analog measurements are stored in the appro-
priate limit registers. In the case of voltage measurements, high
and low limits can be stored so that an interrupt request will be
generated if the measured value goes above or below acceptable
values. In the case of temperature, a Hot Temperature or High
Limit can be programmed, and a Hot Temperature Hysteresis
or Low Limit, which will usually be some degrees lower. This
can be useful as it allows the system to be shut down when the
hot limit is exceeded, and restarted automatically when it has
cooled down to a safe temperature.
MONITORING CYCLE TIME

The monitoring cycle begins when a 1 is written to the Start Bit
(Bit 0), and a 0 to the INT_Clear Bit (Bit 3) of the Configuration
Register. INT_Enable (Bit 1) should be set to 1 to enable the
INT output. The ADC measures each analog input in turn; as
each measurement is completed, the result is automatically
stored in the appropriate value register. This “round-robin”
monitoring cycle continues until it is disabled by writing a 0 to
Bit 0 of the Configuration Register.
As the ADC will normally be left to free-run in this manner, the
time taken to monitor all the analog inputs will normally not be
of interest, as the most recently measured value of any input can
be read out at any time.
For applications where the monitoring cycle time is important,
it can be calculated as follows:
where:is the number of inputs configured as analog inputs, plus the
internal VCC measurement and internal temperature sensor.is the time taken for an analog input conversion, nominally
6.044 ms.is the number of inputs configured as external temperature
inputs.is the time taken for a temperature conversion, nominally
33.24 ms.
This rapid sampling of the analog inputs ensures a quick response
in the event of any input going out of limits, unlike other moni-
toring chips that employ slower ADCs.
FAN MONITORING CYCLE TIME

When a monitoring cycle is started, monitoring of the fan speed
inputs begins at the same time as monitoring of the analog inputs.
However, the two monitoring cycles are not synchronized in any
way. The monitoring cycle time for the fan inputs is dependent
on fan speed and is much slower than for the analog inputs. For
more details, see the Fan Speed Measurement section.
INPUT SAFETY
Scaling of the analog inputs is performed on chip, so external
attenuators are normally not required. However, since the power
supply voltages will appear directly at the pins, it is advisable
to add small external resistors in series with the supply traces
to the chip to prevent damaging the traces or power supplies
should an accidental short such as a probe connect two power
supplies together.
As the resistors will form part of the input attenuators, they will
affect the accuracy of the analog measurement if their value is
too high. The analog input channels are calibrated assuming an
external series resistor of 500 Ω, and the accuracy will remain
within specification for any value from 0 kΩ to 1 kΩ, so a stan-
dard 510 Ω resistor is suitable.
The worst such accident would be connecting –12 V to +12 V—
a total of 24 V difference. With the series resistors, this would
draw a maximum current of approximately 24 mA.
Figure 9a.Fan Drive Circuit with Op Amp and
Emitter-Follower
Figure 9b.Fan Drive Circuit with Op Amp and
PNP Transistor
Figure 9c.Fan Driver Circuit with Op Amp and
P-Channel MOSFET
Figure 9d.Discrete Fan Drive Circuit with
P-Channel MOSFET, Single Supply
+12V
AOUT
4.7k�
–12V

Figure 9e.Discrete Fan Drive Circuit with
P-Channel MOSFET, Dual Supply
Figure 9f.Discrete Fan Drive Circuit with Bipolar
Output Dual Supply
ADM1024
ANALOG OUTPUT

The ADM1024 has a single analog output from an unsigned 8-bit
DAC that produces 0 V to 2.5 V. The analog output register
defaults to FF during power-on reset, which produces maximum
fan speed. The analog output may be amplified and buffered
with external circuitry such as an op amp and transistor to
provide fan speed control.
Suitable fan drive circuits are given in Figures 9a to 9f. When
using any of these circuits, the following points should be noted:All of these circuits will provide an output range from 0 V to
almost 12 V, apart from Figure 9a which loses the base-
emitter voltage drop of Q1 due to the emitter-follower
configuration.To amplify the 2.5 V range of the analog output up to 12 V,
the gain of these circuits needs to be around 4.8.Care must be taken when choosing the op amp to ensure
that its input common-mode range and output voltage swing
are suitable.The op amp may be powered from the 12 V rail alone or
from ±12 V. If it is powered from 12 V, then the input com-
mon-mode range should include ground to accommodate the
minimum output voltage of the DAC, and the output voltage
should swing below 0.6 V to ensure that the transistor can be
turned fully off.If the op amp is powered from –12 V, precautions such as a
clamp diode to ground may be needed to prevent the base-
emitter junction of the output transistor being reverse-biased
in the unlikely event that the output of the op amp should
swing negative for any reason.In all these circuits, the output transistor must have an ICMAX
greater than the maximum fan current, and be capable of
dissipating power due to the voltage dropped across it when
the fan is not operating at full speed.If the fan motor produces a large back EMF when switched
off, it may be necessary to add clamp diodes to protect the
output transistors in the event that the output goes very
quickly from full scale to zero.
FAULT-TOLERANT FAN CONTROL

The ADM1024 incorporates a fault-tolerant fan control capabil-
ity that can override the setting of the analog output and force it
to maximum to give full fan speed in the event of a critical over-
temperature problem even if, for some reason, this has not been
handled by the system software.
There are four temperature set points that will force the analog
output to FFh if any one of them is exceeded for three or more
consecutive measurements. Two of these limits are programmable
by the user and two are hardware limits intended as must-not-
exceed limits that cannot be changed.
The analog output will be forced to FFh if:
The temperature measured by the on-chip sensor exceeds the
limit programmed into register address 13h.
The temperature measured by the on-chip sensor exceeds 70°C,
which is hardware programmed into a read-only register at
address 17h.
The temperature measured by either of the remote sensors exceeds
85°C, which is hardware programmed into a read-only register
at address 18h.
Once the hardware override of the analog output is triggered, it will
return to normal operation only after three consecutive measure-
ments that are 5 degrees lower than each of the above limits.
The analog output can also be forced to FFh by pulling the
THERM pin (Pin 2) low.
The limits in Registers 13h and 14h can be programmed by the
user. Obviously, these limits should not exceed the hardware
values in Registers 17h and 18h, as they would have no ef-
fect. The power-on default values of these registers are the same
as the two hardware registers, 70°C and 85°C respectively, so
there is no need to program them if these limits are acceptable.
Once these registers have been programmed, or if the defaults
are acceptable, the values in these registers can be locked by
writing a 1 to Bits 1 and 2 of Configuration Register 2 (address
4Ah). This prevents any unauthorized tampering with the lim-
its. These lock bits can only be written to 1 and can only be
cleared by power-on reset or by taking the RESET pin low, so
registers 13h and 14h cannot be written to again unless the
device is powered off, then on.
LAYOUT AND GROUNDING

Analog inputs will provide best accuracy when referred to a
clean ground. A separate, low impedance ground plane for
analog ground, which provides a ground point for the voltage
dividers and analog components, will provide best performance
but is not mandatory.
The power supply bypass, the parallel combination of 10 µF
(electrolytic or tantalum) and 0.1 µF (ceramic) bypass capaci-
tors connected between Pin 9 and ground, should also be
located as close as possible to the ADM1024.
FAN INPUTS

Pins 5 and 6 may be configured as analog inputs or fan speed
inputs by programming Bits 0 and 1 of the Channel Mode
Register. The power-on default for these bits is all zeros, which
makes Pins 5 and 6 fan inputs.
Signal conditioning in the ADM1024 accommodates the slow
rise and fall times typical of fan tachometer outputs. The maxi-
mum input signal range is 0 to VCC. In the event that these
inputs are supplied from fan outputs that exceed 0 V to 6.5 V,
either resistive attenuation of the fan signal or diode clamping
must be included to keep inputs within an acceptable range.
Figures 10a to 10d show circuits for most common fan ta-
chometer outputs.
If the fan tachometer output has a resistive pull-up to VCC, it
can be directly connected to the fan input, as shown in Figure 10a.
ic,good price


TEL:86-533-2716050      FAX:86-533-2716790
   

©2020 IC PHOENIX CO.,LIMITED