IC Phoenix
 
Home ›  AA10 > AD607,Low Power Mixer/AGC/RSSI 3V Receiver IF Subsystem
AD607 Fast Delivery,Good Price
Part Number:
If you need More Quantity or Better Price,Welcom Any inquiry.
We available via phone +865332716050 Email
Partno Mfg Dc Qty AvailableDescript
AD607AD N/a10avaiLow Power Mixer/AGC/RSSI 3V Receiver IF Subsystem


AD607 ,Low Power Mixer/AGC/RSSI 3V Receiver IF SubsystemSPECIFICATIONS (@ T = 25C, Supply = 3.0 V, IF = 10.7 MHz, unless otherwise noted.)AAD607ARSModel C ..
AD607ARS ,Low Power Mixer/AGC/RSSI 3 V Receiver IF SubsystemSpecifications subject to change without notice.–2– REV. 0AD6071ORDERING GUIDEABSOLUTE MAXIMUM RATI ..
AD608AR ,Low Power Mixer/Limiter/RSSI 3 V Receiver IF SubsystemSPECIFICATIONSAModel AD608Conditions Min Typ Max UnitsMIXER PERFORMANCERF and LO Frequency Range 50 ..
AD6122ARS ,CDMA 3 V Transmitter IF Subsystem with Integrated Voltage RegulatorSPECIFICATIONS (T = +25C, V = +3.0 V, LO = 2  IF, REFIN = 1.23 V, LDO Enabled, unless otherwiseA ..
AD6190ARS ,900 MHz RF Transceiverapplications. Con-tact Zilog directly at (408) 370-8000 for more information onthe Z87000 series ba ..
AD6190ARSRL ,900 MHz RF TransceiverSPECIFICATIONSParameter Conditions Min Typ Max UnitsRECEIVE RF SECTION(LNA to Mixer Output) Source ..
AD9884AKSZ-100 ,Triple 8-Bit, 140 MSPS ADC, RGB Graphics Digitizer for SXGA LCD MonitorsSPECIFICATIONSTest AD9884AKS-100 AD9884AKS-140Parameter Temp Level Min Typ Max Min Typ Max UnitRESO ..
AD9886KS-100 ,Complete 8-Bit 140 MSPS Analog InterfaceGENERAL DESCRIPTIONB A/DCLAMPIN8BOUTBThe AD9886 is a complete 8-bit 140 MSPS monolithic analoginter ..
AD9886KS-140 ,Complete 8-Bit 140 MSPS Analog InterfaceSPECIFICATIONSD DDTest AD9886KS-100 AD9886KS-140Parameter Temp Level Min Typ Max Min ..
AD9887KS-100 ,Dual Interface for Flat Panel DisplaysSPECIFICATIONSANALOG INTERFACE (V = 3.3 V, V = 3.3 V, ADC Clock = Maximum Conversion Rate, unless o ..
AD9887KS-140 ,Dual Interface for Flat Panel DisplaysGENERAL DESCRIPTION2A0DATACKThe AD9887 offers designers the flexibility of a dual analog andHSOUTdi ..
AD9888KS-100 ,100/140/170/205 MSPS Analog Flat Panel InterfaceSPECIFICATIONSD DD1Test AD9888KS-100/-140 AD9888KS-170 AD9888KS-205Parameter Temp Level Min Typ Max ..


AD607
Low Power Mixer/AGC/RSSI 3V Receiver IF Subsystem
REV.CLow Power Mixer
3 V Receiver IF Subsystem
FEATURES
Complete Receiver-on-a-Chip: Monoceiver® Mixer
–15 dBm 1 dB Compression Point
–8 dBm Input Third Order Intercept
500 MHz RF and LO Bandwidths
Linear IF Amplifier
Linear-in-dB Gain Control
Manual Gain Control
Quadrature Demodulator
On-Board Phase-Locked Quadrature Oscillator
Demodulates IFs from 400 kHz to 12 MHz
Can Also Demodulate AM, CW, SSB
Low Power
25 mW at 3 V
CMOS Compatible Power-Down
Interfaces to AD7013 and AD7015 Baseband Converters
APPLICATIONS
GSM, CDMA, TDMA, and TETRA Receivers
Satellite Terminals
Battery-Powered Communications Receivers
PIN CONFIGURATION
20-Lead SSOP
(RS Suffix)
GENERAL DESCRIPTION

The AD607 is a 3 V low power receiver IF subsystem for opera-
tion at input frequencies as high as 500 MHz and IFs from
400 kHz to 12 MHz. It consists of a mixer, IF amplifiers, I and
Q demodulators, a phase-locked quadrature oscillator, and a
biasing system with external power-down.
The AD607’s low noise, high intercept mixer is a doubly
balanced Gilbert cell type. It has a nominal –15 dBm input
referred 1 dB compression point and a –8 dBm input referred
third order intercept. The mixer section of the AD607 also
includes a local oscillator (LO) preamplifier, which lowers the
required LO drive to –16 dBm.
In MGC operation, the AD607 accepts an external gain-control
voltage input from an external AGC detector or a DAC.
The I and Q demodulators provide in-phase and quadrature
baseband outputs to interface with Analog Devices’ AD7013
(IS54, TETRA, MSAT) and AD7015 (GSM) baseband con-
verters. A quadrature VCO phase-locked to the IF drives the I
and Q demodulators. The I and Q demodulators can also
demodulate AM; when the AD607’s quadrature VCO is phase-
locked to the received signal, the in-phase demodulator becomes
a synchronous product detector for AM. The VCO can also be
phase-locked to an external beat-frequency oscillator (BFO),
and the demodulator serves as a product detector for CW or
SSB reception. Finally, the AD607 can be used to demodulate
BPSK using an external Costas Loop for carrier recovery.
Monoceiver is a registered trademark of Analog Devices, Inc.
AD607–SPECIFICATIONS
(@ TA = 25�C, Supply = 3.0 V, IF = 10.7 MHz, unless otherwise noted.)
ORDERING GUIDE
ABSOLUTE MAXIMUM RATINGS1

SupplyVoltage VPS1, VPS2 to COM1, COM2 . . . . . . .5.5V
InternalPowerDissipation2 . . . . . . . . . . . . . . . . . . . .600 mW
2.92V to 5.5VOperatingTemperatureRange
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –25°Cto+85°C
4.5V to 5.5V Operating Temperature Range
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –40°C to +85°C
Storage Temperature Range . . . . . . . . . . . .–65°C to +150°C
Lead Temperature Range (Soldering60sec) . . . . . . . . .300°C
NOTES
1Stresses above those listed under Absolute Maximum Rating may cause perma-
nent damage to the device. This is a stress rating only; functional operation of the
device at these or any other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability.
2Thermal Characteristics: 20-lead SSOP Package: θJA = 126°C/W.
CAUTION

ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000V readily
accumulate on the human body and test equipment and can discharge without detection. Although the
AD607 features proprietary ESD protection circuitry, permanent damage may occur on devices
subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended
to avoid performance degradation or loss of functionality.
AD607
PIN FUNCTION DESCRIPTIONS

PIN CONNECTION
20-Lead SSOP (RS-20)
Figure 1.Mixer/Amplifier Test Set
Figure 2.Mixer Noise Figure Test Set
AD607
Figure 3.IF Amp Noise Figure Test Set
Figure 4.PLL/Demodulator Test Set
Figure 5.GAIN Pin Bias Test Set
Figure 6.Demodulator Bias Test Set
AD607
Figure 8.Power-Up Test Set
Figure 9.IF Output Impedance Test Set
Figure 10.PLL Settling Time Test Set
Figure 11.Quadrature Accuracy Test Set
AD607
Figure 12.Characterization Board
TPC 1.Mixer Noise Figure vs. Frequency
TPC 2.Mixer Input Impedance vs. Frequency,
VPOS = 3 V, V GAIN = 0.8 V
TPC 3.Mixer Conversion Gain vs. Frequency,
T = 25°C, VPOS = 2.92 V, VREF = 1.35 V, IF = 10.7 MHz
TPC 4.Mixer Conversion Gain vs. IF, T = 25°C,
VPOS = 3 V, VREF = 1.5 V
TPC 5.Mixer Conversion Gain and IF Amplifier Gain vs.
Temperature, VPOS = 3 V, VGAIN = 0.3 V, VREF = 1.5 V, IF =
10.7 MHz, RF = 250 MHz
TPC 6.Mixer Conversion Gain and IF Amplifier Gain vs.
Supply Voltage, T = 25°C, VGAIN = 0.3 V, VREF = 1.5 V, IF =
10.7 MHz, RF = 250 MHz
AD607
TPC 7.IF Amplifier Gain vs. Frequency,
T = 25°C, VPOS = 3 V, VREF = 1.5 V
TPC 8.Gain Error vs. Gain Control Voltage,
Representative Part
TPC 9.PLL Acquisition Time
TPC 10.PLL Phase Noise L (F) vs. Frequency,
VPOS = 3 V, C3 = 0.1 µF, IF = 10.7 MHz
TPC 11.PLL Loop Voltage at FLTR (KVCO) vs. Frequency
TPC 12.Demodulator Quadrature Angle, Histogram,
T = 25°C, VPOS = 3 V, IF = 10.7 MHz
ic,good price


TEL:86-533-2716050      FAX:86-533-2716790
   

©2020 IC PHOENIX CO.,LIMITED