VND600SPTR-E ,DOUBLE CHANNEL HIGH SIDE SOLID STATE RELAYBlock diagram . . . . 5Figure 2. Configuration diagram (top view) . . . . . 5Figure 3. ..
VND670SP13TR ,DUAL HIGH SIDE SWITCH WITH DUAL POWER MOS GATE DRIVER (BRIDGE CONFIGURATION)ELECTRICAL CHARACTERISTICS (V =9V up to 18V; -40°C
VND7N04 ,鯫MNIFET? FULLY AUTOPROTECTED POWER MOSFETABSOLUTE MAXIMUM RATINGSymbol Parameter Value UnitDPAK ISOWATT220 SOT-82FMIPAKV Drain-source Voltag ..
VND7N04TR-E ,OMNIFET :FULLY AUTOPROTECTED POWER MOSFETElectrical specification2.1 Absolute maximum rating Table 2. Absolute maximum ratingValueSy ..
VND7NV04 ,"OMNIFET II": FULLY AUTOPROTECTED POWER MOSFETELECTRICAL CHARACTERISTICS (continued) (T =25°C, unless otherwise specified)jDYNAMICSymbol Paramete ..
VND7NV0413TR ,“OMNIFET II”: FULLY AUTOPROTECTED POWER MOSFETFEATURES - OVERTEMPERATURE AND SHORT CIRCUITPROTECTION: these are based on sensing theDuring normal ..
WFF10N65 , Silicon N-Channel MOSFET
WFF12N65 , Silicon N-Channel MOSFET
WFF2N60 , Silicon N-Channel MOSFET
WFF2N60 , Silicon N-Channel MOSFET
WFF2N60 , Silicon N-Channel MOSFET
WFF630 , Silicon N-Channel MOSFET
VND600SPTR-E
DOUBLE CHANNEL HIGH SIDE SOLID STATE RELAY
September 2013 Doc ID 10876 Rev 4 1/27
VND600SP-E
Double channel high-side driver
Features ECOPACK® : lead free and RoHS compliant Automotive Grade: compliance with AEC
Guidelines Very low standby current CMOS compatible input Proportional load current sense Current sense disable Thermal shutdown protection and diagnosis Undervoltage shutdown Overvoltage clamp Load current limitation
Description
The VND600SP-E is a monolithic device made
using STMicroelectronics™ VIPower™ M0-3
technology. It is intended for driving resistive or
inductive loads with one side connected to
ground. Active VCC pin voltage clamp protects the
device against low energy spikes (see ISO7637
transient compatibility table).
This device has two channels in high-side
configuration; each channel has an analog sense
output on which the sensing current is
proportional (according to a known ratio) to the
corresponding load current.
Built-in thermal shutdown and outputs current
limitation protect the chip from overtemperature
and short circuit. Device turns-off in case of
ground pin disconnections.
Table 1. Device summary
Contents VND600SP-E
2/27 Doc ID 10876 Rev 4
Contents Block diagram and pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Electrical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.1 Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.2 Thermal data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.3 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.4 Electrical characteristics curves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Application information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3.1 GND protection network against reverse battery . . . . . . . . . . . . . . . . . . . 17
3.1.1 Solution 1: resistor in the ground line (RGND only) . . . . . . . . . . . . . . . . 17
3.1.2 Solution 2: diode (DGND) in the ground line . . . . . . . . . . . . . . . . . . . . . 18
3.2 Load dump protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
3.3 MCU I/Os protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
3.4 PowerSO-10 maximum demagnetization energyCC = 13.5 V) 19 Package and PCB thermal data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
4.1 PowerSO-10 thermal data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Package and packing information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
5.1 ECOPACK® packages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
5.2 PowerSO-10 mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
5.3 PowerSO-10 packing information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
VND600SP-E List of tables
Doc ID 10876 Rev 4 3/27
List of tables
Table 1. Device summary. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Table 2. Suggested connections for unused and not connected pins . . . . . . . . . . . . . . . . . . . . . . . . 5
Table 3. Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Table 4. Thermal data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Table 5. Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Table 6. Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Table 7. VCC - output diode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Table 8. Current sense 9 V≤ VCC≤ 16 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Table 9. Switching (VCC=13 V). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Table 10. Logic input (channel 1, 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Table 11. Truth table (per each channel) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Table 12. Electrical transient requirements on VCC pin (part 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Table 13. Electrical transient requirements on VCC pin (part 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Table 14. Electrical transient requirements on VCC pin (part 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Table 15. Thermal parameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Table 16. PowerSO-10 mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Table 17. Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
List of figures VND600SP-E
4/27 Doc ID 10876 Rev 4
List of figures
Figure 1. Block diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Figure 2. Configuration diagram (top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Figure 3. Current and voltage conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Figure 4. Switching characteristics (resistive load RL=2.6 Ω). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Figure 5. IOUT/ISENSE versus IOUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Figure 6. Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Figure 7. Off-state output current. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Figure 8. High level input current. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Figure 9. Input low level. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Figure 10. Input high level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Figure 11. Input clamp voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Figure 12. Input hysteresis voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Figure 13. Overvoltage shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Figure 14. ILIM vs Tcase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Figure 15. Turn-on voltage slope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Figure 16. Turn-off voltage slope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Figure 17. On-state resistance vs Tcase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Figure 18. On-state resistance vs VCC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Figure 19. Application schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Figure 20. Maximum turn- off current versus load inductance(1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Figure 21. PowerSO-10 PC board(1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Figure 22. Rthj-amb vs PCB copper area in open box free air condition. . . . . . . . . . . . . . . . . . . . . . . 20
Figure 23. PowerSO-10 thermal impedance junction ambient single pulse. . . . . . . . . . . . . . . . . . . . . 21
Figure 24. Thermal fitting model of a double channel HSD in PowerSO-10 . . . . . . . . . . . . . . . . . . . . 21
Figure 25. PowerSO-10 package dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Figure 26. PowerSO-10 suggested pad layout and tube shipment (no suffix). . . . . . . . . . . . . . . . . . . 25
Figure 27. Tape and reel shipment (suffix “TR”) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
VND600SP-E Block diagram and pin description
Doc ID 10876 Rev 4 5/27 Block diagram and pin description
Figure 1. Block diagram
Figure 2. Configuration diagram (top view)
Table 2. Suggested connections for unused and not connected pins
Electrical specifications VND600SP-E
6/27 Doc ID 10876 Rev 4
2 Electrical specifications
Figure 3. Current and voltage conventions
1) VFn = VCCn - VOUTn during reverse battery condition
2.1 Absolute maximum ratings
Stressing the device above the rating listed in Table 3 may cause permanent damage to the
device. These are stress ratings only and operation of the device at these or any other
conditions above those indicated in the operating sections of this specification is not implied.
Exposure to absolute maximum rating conditions for extended periods may affect device
reliability. Refer also to the STMicroelectronics sure program and other relevant quality
document.
Table 3. Absolute maximum ratings
VND600SP-E Electrical specifications
Doc ID 10876 Rev 4 7/27
2.2 Thermal data
Table 3. Absolute maximum ratings (continued)
Table 4. Thermal data When mounted on a standard single sided FR-4 board with 0.5cm2 of Cu (at least 35 μm thick). When mounted on a standard single-sided FR-4 board with 6cm2 of Cu (at least 35 μm thick).
Electrical specifications VND600SP-E
8/27 Doc ID 10876 Rev 4
2.3 Electrical characteristics
Values specified in this section are for 8 V < VCC < 36 V; -40 °C < Tj < 150 °C, unless
otherwise stated. (Per each channel).
Table 5. Power Per device. Vclamp and VOV are correlated. Typical difference is 5V.
Table 6. Protection(1)
VND600SP-E Electrical specifications
Doc ID 10876 Rev 4 9/27
To ensure long term reliability under heavy overload or short circuit conditions, protection and related
diagnostic signals must be used together with a proper software strategy. If the device is subjected to
abnormal conditions, this software must limit the duration and number of activation cycles
Table 7. VCC - output diode
Table 6. Protection(1) (continued)
Table 8. Current sense 9 V≤VCC≤ 16 V
Electrical specifications VND600SP-E
10/27 Doc ID 10876 Rev 4
Current sense signal delay after positive input slope.
Table 8. Current sense 9 V≤ VCC≤ 16 V (continued)
Table 9. Switching (VCC =13V)
Table 10. Logic input (channel 1, 2)
VND600SP-E Electrical specifications
Doc ID 10876 Rev 4 11/27
Figure 4. Switching characteristics (resistive load RL=2.6Ω)
Figure 5. I OUT/I SENSE versus I OUT
Electrical specifications VND600SP-E
12/27 Doc ID 10876 Rev 4
Table 11. Truth table (per each channel)
VND600SP-E Electrical specifications
Doc ID 10876 Rev 4 13/27
Table 12. Electrical transient requirements on VCC pin (part 1)
Table 13. Electrical transient requirements on VCC pin (part 2)
Table 14. Electrical transient requirements on VCC pin (part 3)
Electrical specifications VND600SP-E
14/27 Doc ID 10876 Rev 4
Figure 6. Waveforms
