VN460SP ,SINGLE CHANNEL HIGH SIDE SMART POWER SOLID STATE RELAYVN460SP SINGLE CHANNEL HIGH SIDE SMARTSOLID STATE RELAYTYPE V R IOUT Vdema g DS(on) CCVN460SP V -5 ..
VN460SP ,SINGLE CHANNEL HIGH SIDE SMART POWER SOLID STATE RELAYELECTRICAL CHARACTERISTICS (VCC = 13 V; -40 C
VN460SP13TR ,SINGLE CHANNEL HIGH SIDE SMART POWER SOLID STATE RELAYABSOLUTE MAXIMUM RATINGSymbol Parameter Value UnitV Power Supply Voltage (continuous) 45 VCC-V Reve ..
VN5010AK-E ,Single channel high side switchBlock diagram . . . . 5Figure 2. Connection diagram (top view) . . . . . . . 6Figure 3. ..
VN5010AKTR-E ,Single channel high side switchfeatures ■ All types of resistive, inductive and capacitive – Inrush current active management by p ..
VN5010AKTR-E ,Single channel high side switchElectrical characteristics curves 183 Application information . . . . . 213.1 GND protecti ..
WE2408 , 2.4GHz Single Chip FM Transceiver
WE9140A , TONE/PULSE SWITCHABLE DIALER WITH REDIAL
WE9140A , TONE/PULSE SWITCHABLE DIALER WITH REDIAL
WE9140G , TONE/PULSE SWITCHABLE DIALER WITH REDIAL
WE9140J , TONE/PULSE SWITCHABLE DIALER WITH REDIAL
WE9142 , 10-MEMORY TONE/PULSE SWITCHABLE DIALER
VN460SP-VN460SP13TR
SINGLE CHANNEL HIGH SIDE SMART POWER SOLID STATE RELAY
VN460SP
SINGLE CHANNEL HIGH SIDE SMART
SOLID STATE RELAY
June 1998
Power SO-10TM
BLOCK DIAGRAM
TYPE Vdemag RDS(on) IOUT VCC
VN460SP VCC-55V 20mΩ 25A 36V OUTPUT CURRENT (CONTINUOUS):A@TC =25oC 5V LOGIC LEVEL COMPATIBLE INPUT UNDER VOLTAGE SHUT-DOWN OVER VOLTAGE SHUT-DOWN THERMAL SHUT-DOWN OPEN DRAIN DIAGNOSTIC OUTPUT VERY LOW STAND-BY POWER
DISSIPATION
DESCRIPTION
The VN460SPisa monolithic device made using
SGS-THOMSON Vertical Intelligent Power
Technology, intended for driving resistive or
inductive loads with one side connected to
ground.
Built-in thermal shut-down protects the chip from
over temperature and short circuit.
The control input is 5V CMOS logic level
compatible.
The open drain diagnostic output indicates open
circuit (no load) and overtemperature status.
1/9
ABSOLUTE MAXIMUM RATING
Symbol Parameter Value Unit
VCC Power Supply Voltage (continuous) 45 V
-VCC Reverse Supply Voltage (continuous) -0.3 V
IOUT Output Current (continuous) Internally Limited A Reverse Output Current -25 A
IIN Input Current ±10 mA
ISTAT Status Pin Current ±10 mA
-IGND Reverse Ground Current -200 mA
VESD Electrostatic Discharge (1.5 kΩ, 100 pF) 2000 V
Ptot Power DissipationatTc≤25o C112 W Junction Operating Temperature -40to 150 oC
Tstg Storage Temperature -55to 150 oC
CONNECTION DIAGRAM
CURRENT AND VOLTAGE CONVENTIONS
VN460SP
2/9
ELECTRICAL TRANSIENTS REQUIREMENTS
ISO T/R
7637/1
Test Pulse
TEST LEVELS II III IV Delays and
Impedance -25V -50V -75V -100V 2 ms,10Ω +25V +50V +75V +100V 0.2 ms,10Ω -25V -50V -100V -150V 0.1 μs,50Ω +25V +50V +75V +100V 0.1 μs,50Ω -4V -5V -6V -7V 100 ms, 0.01Ω +26.5 +46.5 +66.5 +86.5 400 ms,2Ω
ISO T/R
7637/1
Test Pulse
TEST LEVELS RESULTS II III IV C C C C C C C C C C C C C C C C C E E E
(Witha series resistor≥ 1KΩ ininputand statuspins).
CLASS CONTENTS All functionof the device are performedas designed after exposureto disturbance. Oneor more functionsof the deviceis not performedas designed after exposure and
cannotbe returnedto proper operation without replacing the device.
VN460SP
3/9
THERMAL DATA
Rthj-case Thermal Resistance Junction-case Max 1.1 o C/W
Rthj-a(∗) Thermal Resistance Junction-ambient Max 50 o C/W
(∗) When mounted using minimum recommended padsizeon FR-4 board.
ELECTRICAL CHARACTERISTICS (VCC=13V; -40o CPOWER
Symbol Parameter Test Conditions Min. Typ. Max. Unit
VCC Operating Supply
Voltage
5.5 13 36 V
Vusd Under Voltage Shut
Down 5.5 V
Vov Overvoltage Shut Down 36 39 45 V
Ron On State Resistance IOUT =5A TJ =25oC
IOUT =5A Supply Current Off state TCase =25oC State
LOGIC INPUT
Symbol Parameter Test Conditions Min. Typ. Max. Unit
VIL Input Low Level
Voltage
(*) 1.5 V
VIH Input High Level
Voltage (see note1)
(*) 3.5 V
VI(hyst.) Input Hysteresis
Voltage
0.2 0.85 1.5 V
IIN Input Current VIN =5V Tcase =25o C100 μA
VICL Input Clamp Voltage IIN =10 mA
IIN =-10 mA
(*) :The input voltageis internallyclampedat6V about.Itis possibleto connect thispintoan higher voltageviaan externalresistor
providedthe input current doesnot exceed10 mA.
SWITCHING (VCC =13V)
Symbol Parameter Test Conditions Min. Typ. Max. Unit
td(on) Turn-on Delay TimeOf
Output Current
IOUT=5A Resistive Load
Input Rise Time< 0.1 μsTj =25oC 90 250 μs Rise TimeOf Output
Current
IOUT=5A Resistive Load
Input Rise Time< 0.1 μsTj =25oC 300 650 μs
td(off) Turn-off Delay TimeOf
Output Current
IOUT=5A Resistive Load
Input Rise Time< 0.1 μsTj =25oC
300 750 1500 μs Fall TimeOf Output
Current
IOUT=5A Resistive Load
Input Rise Time< 0.1 μsTj =25oC 200 400 μs
(di/dt)on Turn-on Current Slope IOUT =5A 0.02 0.05 A/μs
(di/dt)off Turn-off Current Slope IOUT =5A 0.02 0.05 A/μs
VN460SP
4/9
ELECTRICAL CHARACTERISTICS (continued)
PROTECTIONS AND DIAGNOSTICS
Symbol Parameter Test Conditions Min. Typ. Max. Unit
TTSD Thermal Shut-down
Temperature
150 170 190 oC
TTR Thermal Reset
Temperature
135 oC
TRSD
(HYST)
Thermal Hysteresis 5 15 50 oC
VENOL Output Voltage
Authorizing Openload
Detection
8V≤VCC≤30V 5.2 6.6 8 V
IOL Open Load Current
Level
8V≤VCC≤30V 100 800 1500 mA
IOV Over Current RLOAD ≤10 mΩ
-40o CIAV Average Currentin
Short Circuit
RLOAD ≤10 mΩ =85oC
5.4 A
VSTAT Status Output Voltage ISTAT= 1.6 mA (Fault Condition) 0.4 V
VSCL Status Clamp Voltage ISTAT =10 mA
ISTAT =-10 mA
5.5 6
tPOL Status Delay (∗) 50 300 950 μs
tPOVL Status Delay (∗)10 μs
VDEMAG Turn-off Output Clamp
Voltage
IOUT =5A,L=1 mH, VIN =0 VCC-45 VCC-50 VCC-55 V
(∗) ISO definitions TPOL= Statusdelayin caseof open loadconditions
TPOVL= Statusdelay incaseof over load conditions
VN460SP
5/9
TRUTH TABLE
Conditions INPUT OUTPUT STATUS
Normal Operation L
Over-voltage X L H
Under-voltage X L H
Thermal shut-down H L L
Open load H H L= high level,L= low level, X= unspecified
SWITCHING PARAMETERS TEST CONDITIONS
FIGURE1
VN460SP
6/9
