IC Phoenix
 
Home ›  VV1 > V23826-K15-C13-V23826-K15-C363-V23826-K15-C73,SM 1.0625 GBd FC Transceiver
V23826-K15-C13-V23826-K15-C363-V23826-K15-C73 Fast Delivery,Good Price
Part Number:
If you need More Quantity or Better Price,Welcom Any inquiry.
We available via phone +865332716050 Email
Partno Mfg Dc Qty AvailableDescript
V23826-K15-C13 |V23826K15C13SIEMENSN/a6avaiSM 1.0625 GBd FC Transceiver
V23826-K15-C363 |V23826K15C363LNFINEONN/a4avaiSM 1.0625 GBd FC Transceiver
V23826-K15-C73 |V23826K15C73INFINEONN/a15avaiSM 1.0625 GBd FC Transceiver


V23826-K15-C73 ,SM 1.0625 GBd FC TransceiverFunctional DescriptionThe transmitter converts electrical PECL compatible serial data This transcei ..
V23826-K305-C363 ,MM 1.0625 GBd FC TransceiverCharacteristicsThe electro-optical
V23826-K305-C53 ,MM 1.0625 GBd FC Transceiver123456789

V23826-K15-C13-V23826-K15-C363-V23826-K15-C73
SM 1.0625 GBd FC Transceiver
(5V/3.3V) V23826-K15-C(*)
Single Mode 1300 nm 1.0625 GBd Fibre Channel
1.3 Gigabit Ethernet 1x9 Transceiver
FEATURESCompliant with Fibre Channel and Gigabit Ethernet
standardMeets mezzanine standard height of 9.8 mmCompact integrated transceiver unit withMQW laser diode transmitterInGaAs PIN photodiode receiverDuplex SC receptacleClass 1 FDA and IEC laser safety compliantSingle power supply (5 V or 3.3 V)Signal detect indicator (PECL and TTL version)PECL differential inputs and outputsProcess plug includedInput Signal Monitor (DC/DC-Version)Performance exceeds FC 100-SM-LL-IWave solderable and washable with process plug
insertedFor distances of up to 10 km on single mode fiber, and up
to 550 m on multimode fiber (use offset jumper as speci-
fied in IEEE 802.3)
Absolute Maximum Ratings

Exceeding any one of these values may destroy the device
immediately.
Package Power Dissipation(1)........................................................1.5 W
Supply Voltage (VCC–VEE)5 V..............................................6 V
3.3 V...........................................4 V
Data Input Levels (PECL)........................................... VCC+0.5 V
Differential Data Input Voltage............................................2.5 V
Operating Ambient Temperature...............................0° to 70°C
Storage Ambient Temperature............................–40°C to 85°C
Soldering Conditions Temp/Time
(MIL-STD 883C, Method 2003).............................250°C/5.5s
Note
1. For VCC–VEE (min., max.). 50% duty cycle. The supply current does
not include the load drive current of the receiver output.
*) Ordering Information

Note
1. Standard version
DESCRIPTION
The Infineon single mode transceiver is based on the Physical
Medium Depend (PMD) sublayer and baseband medium, type
1000BASE-LX (Long Wavelength Laser) (IEEE 802.5) and com-
plies with the Fibre Channel Physical and Signaling Interface
(FC-PH), ANSI XSI TT Fibre Channel Physical Standard Class
100-SM-LL-I, latest Revision.
The appropriate fiber optic cable is 9 µm (mode field diameter)
single mode fiber (up to 10 km) with Duplex SC connector.
The Infineon single mode transceiver is a single unit comprised
of a transmitter, a receiver, and an SC receptacle. This design
frees the customer from many alignment and PC board layout
concerns. The module is designed for low cost LAN, WAN and
Gigabit Ethernet applications. It can be used as the network
end device interface in mainframes, workstations, servers, and
storage devices, and in a broad range of network devices such
as bridges, routers, intelligent hubs, and local and wide area
switches.
This transceiver operates at 1.0625 and 1.3 Gbit/s from a single
power supply (+5 Volt or 3.3 Volt). The full differential data
inputs and outputs are PECL compatible.
Functional Description

This transceiver is designed to transmit serial data via single
mode or multimode cable.
Functional Diagram

The receiver component converts the optical serial data into
PECL compatible electrical data (RD and RDnot). The Signal
Detect (SD, active high) shows whether an optical signal present.
The transmitter converts electrical PECL compatible serial data
(TD and TDnot) into optical serial data.
The following versions are available:
1. AC/DC Transceiver
Tx is AC coupled. Differential 100 Ω load. Rx has standard PECL
output and is DC coupled.
2. AC/AC TTL Transceiver
Tx and Rx are AC coupled. Tx has differential 100 Ω load. Signal
Detect is TTL compatible.
3. DC/DC Transceiver
Standard PECL inputs and outputs Tx and Rx are DC coupled.
This version contains an Input Signal Monitor (ISM) which
switches off the transceiver if a continuous low level is applied
at Data Input.
4. AC/AC PECL Transceiver
Tx and Rx are AC coupled. Tx has differential 100 Ω load. Signal
Detect is PECL compatible.
The transmitter contains a laser driver circuit that drives the
modulation and bias current of the laser diode. The currents are
controlled by a power control circuit to guarantee constant out-
put power of the laser over temperature and aging.
The power control uses the output of the monitor PIN diode
(mechanically built into the laser coupling unit) as a controlling
signal, to prevent the laser power from exceeding the operating
limits.
Single fault condition is ensured by means of an integrated
automatic shutdown circuit that disables the laser when it
detects transmitter failures. A reset is only possible by turning
the power off, and then on again.
The transceiver contains a supervisory circuit to control the
power supply. This circuit generates an internal reset signal
whenever the supply voltage drops below thereset threshold.
It keeps the reset signal active for at least 140 milliseconds
after the voltage has risen above the reset threshold. During
this time the laser isinactive.
TECHNICAL DATA
The electro-optical characteristics described in the following
tables are only valid for use under the recommended operating
conditions.
Recommended Operating Conditions

Notes
1. For VCC–VEE (min., max.) 50% duty cycle. The supply current does
not include the load drive current of the receiver output.Peak to peak voltage of one input.ransmitter Electro-Optical Characteristics
Notes. Into single mode fiber, 9 µm diameter.
2. Laser power is shut down if power supply is below VTH and
switched on if power supply is above VTH after tRES.
Receiver Electro-Optical Characteristics

Notes
1. Minimum average optical power at which the BER is less than
1x10E-12 or lower. Measured with a 27-1 NRZ PRBS and ER=9 dB.
Output of single mode fiber 9 µm diameter.
2. An increase in optical power above the specified level will cause the
SIGNAL DETECT output to switch from a Low state to a High state.
3. A decrease in optical power below the specified level will cause the
SIGNAL DETECT to change from a High state to a Low state.
4. DC/DC, AC/DC for data
DC/DC, AC/DC, AC/AC PECL for Signal Detect
PECL compatible. Load is 50 Ω into VCC –2 V for data, 500 Ω to V((
for Signal Detect. Measured under DC conditions. For dynamic mea-
surements a tolerance of 50 mV should be added. VCC=3.3 V/5 V.
TAMB=25°C.Max. output current high: –0.4 mA (drive current)
low: +2.0 mA (sink current)AC/AC for data. Load 50 Ω to GND or 100 Ω differential. For dynamic
measurement a tolerance of 50mV should be added.
Pin Description
Regulatory Compliance
EYE SAFETY

This laser based single mode transceiver is a Class 1 product. It
complies with IEC 60825-1 and FDA 21 CFR 1040.10 and
To meet laser safety requirements the transceiver shall be oper-
ated within the Absolute Maximum Ratings.
Caution
All adjustments have been made at the factory prior to ship-
ment of the devices. No maintenance or alteration to the
device is required.
Tampering with or modifying the performance of the device
will result in voided product warranty.

Note
Failure to adhere to the above restrictions could result in a modifica-
tion that is considered an act of “manufacturing,” and will require,
under law, recertification of the modified product with the U.S. Food
and Drug Administration (ref. 21 CFR 1040.10 (i)).
Laser Data
Required Labels
Laser Emission
APPLICATION NOTE
Gigabit transceivers and matching circuits are high frequency
components and shall be terminated as recommended in the
application notes for proper EMI performance. Electromagnetic
emission may be caused by these components.
To prevent emissions it is recommended that cutouts for the
fiber connectors be designed as small as possible.
It is strongly recommended that the Tx plug and the Rx plug be
separated with a bar that divides the duplex SC opening.
If shielded parts are employed, they should be in proper contact
with the bezel (back plane).
Since the shield is galvanically isolated from signal ground it is
strongly recommended to prevent any contact between shield
and the circuitry i.e. even any ground connection on the pcb
may be harmful to EMI performance.
In cases where EMI performance becomes critical it has proven
to be helpful when using SC-plugs with less metal parts inside
(as Infineon fibers).
APPLICATION NOTE
Single Mode 1300 nm Gigabit Ethernet/Fibre Channel 1x9 Transceiver, DC/DC Version

Values of R1/2/3/4 may vary as long as proper 50 Ω termination
to VEE or 100 Ω differential is provided. The power supply filter-
ing is required for good EMI performance. Use short tracks
from the inductor L1/L2 to the module VCCRX/VCCTX. We rec-
ommend a GND plane under the module for getting good EMI
performance.
The transceiver contains an automatic shutdown circuit. Reset only possible if the power is turned off, and then on again.
(VCCTX switched below VTH).
Application Board available onrequest.
The stud pins S1 and S2 are not connected.
APPLICATION NOTE
Single Mode 1300nm Gigabit Ethernet/Fibre Channel 1x9 Transceiver, AC/DC Version

Values of R1/2/3/4 may vary as long as proper 50 Ω termination
to VEE or 100 Ω differential is provided. The power supply filter-
ing is required for good EMI performance. Use short tracks
from the inductor L1/L2 to the module VCCRx/VCCTx. We rec-
ommend a GND plane under the module for getting good EMI
performance.
The transceiver contains an automatic shutdown circuit. Reset only possible if the power is turned off, and then on again.
(VCCTx switched below VTH).
Application Board available onrequest.
The stud pins S1 and S2 are not connected.
ic,good price


TEL:86-533-2716050      FAX:86-533-2716790
   

©2020 IC PHOENIX CO.,LIMITED